8. Determine the effective height of a stack needed to keep the maximum ground level ambient airconcentration below 10 ug/m³ from a source that emits 12 g/s of NQin a rural area with windspeed 4 m/s measured at the stack height, and moderately stable air.

Given:- The maximum ground-level ambient air concentration = 10 μg/m3 Source strength (Q) = 12 g/s…

8. Determine the effective height of a stack needed to keep the maximum ground level ambient air concentration below 10 ug/m from a source that emits 12 g/s of NOin a rural area with wind speed 4 m/s measured at the stack height, and moderately stable air.

8. Determine the effective height of a stack needed to keep the maximum ground level ambient air concentration below 10 ug/m from a source that emits 12 g/s of NOin a rural area with wind speed 4 m/s measured at the stack height, and moderately stable air.

Solid Waste Engineering

3rd Edition

ISBN:9781305635203

Author:Worrell, William A.

Publisher:Worrell, William A.

Chapter5: Separation Processes

Section: Chapter Questions

Problem 5.6P

See similar textbooks

Related questions

Q: À commercial building is built on a slab on grade foundation that is a 40 m by 18 m rectangular…

A: Given, Slab length L=40 m B=18 m Temperature (t)= -15° C

Q: For 100 mm soil stack, and 75 mm vent, a developed length of 78 m of the vent, may service a maximum…

A: ACC to table 10.12 standard size of vent and length of vent For 100mm stack (4in) , 75mm vent (3in)…

Q: 7. Determine the 1 km downwind ground level concentration of PM [ug/m'] from an urban power plant…

A: The given data is: x=1 km Coal burnt per hour=3 tons =3*1000 kg=3000…

Q: Heated air at 1 atm and 35°C is to be transported in a 150-m-long circular plastic duct at a rate of…

A: Considering the given diagram as follows: Given information: Length = 150 m Head loss, hL = 20 m…

Q: A rectangular channel is 25 ft wide and has a flow of 500 cfs at a velocity of 5 ft./sec. (a)…

A: Given:- The width of the rectangular channel = 25 ft The rate of flow = 500 cfs The velocity of the…

Q: i. using the logarithmic and power law, determine the expected wind speed at 50m above ground level.…

Q: Convert 15 inHg vacuum to N/m^2 abs. Assume a biometric pressure of 759 mmHg.

A: Atmospheric pressure and vaccum pressure have been given Hg and it has been asked to determine…

Q: Air at 20°C and approximately 1 atm fl ows through asmooth 30-cm-square duct at 1500 ft3/min. The…

A: Following is the given data:

Q: * stack emitting 80 g/s of NO has an effective stack height of 100 m. The windspeed is mis at 10 m,…

A: Given, Wind speed Va = 4m/s Stark height (H) = 100m Za = 10m Q = 80 x 106 VH = Va(H/Za)P VH =…

Q: In a four-storey building with an overhead head tank located at the roof deck. Which floor has the…

Q: 2. Suppose the following atmospheric altitude versus temperature data have been collected:…

Q: The unheated storage facility shown in Fig. 1-15 is located on flat open terrain in southern…

A: For an unhealty facility located on flat terrainin southern Illinois.Snow load = 15μ/ft2 to find…

Q: The difference in energy grade line between inlet and outlet is 20 cm when Ethyl Alcohol (specific…

A: Given Data: Specific gravity of Ethyl Alcohol is S=0.79. Density of Ethyl Alcohol is given by:…

Q: MAXIMUM AVAILABLE CONCENTRATION (MAC) CO2 FOR AIR OF RESIDENTIAL AND PUBLIC BUILDINGS 1. 0,5 2. 0,1…

A: There are different categories of the buildings in civil engineering. These buildings are having…

Q: A steam generator with economizer and air heater has an over all draft loss of 21.78 cm of water. If…

A: Given Data:Draft loss=21.78cmTemp=177°Catm Temp=101.3kpa and 26°C

Q: Determine the required fire flow for a three storeys wood building covering 750 m which connects…

A: Given: The 3 storey building covering area is 750 m2. The 5 storey building covering area is 900 m2.

Q: (a) Determine the inlet temperature of the supply water that will maintain an average tank surface…

A: Given data: Inner diameter of concentric tube,Di = 80 mm = 0.08 m outer diameter of concentric tube,…

Q: It is desired to deliver 30,000 gal/min of water in a brickworkchannel laid on a slope of 1:100.…

A: Given data: Discharge in channel (Q) = 30,000 gal/min Slope (S) = 1:100 V channel section with angle…

Q: Determine the specific energy of water in the rectangular open channel with following conditions:…

Q: Find the wind speed needed (in miles/hour) to obtain a daily evaporation of 0.163 in/day, if the air…

A: Given Data: Daily Evaporation is EL=0.163 in/day. Air temperature is T=80°F =26.67°C Relative…

Q: SECTION 207C - Buildings MWFRS (Envelope Procedure) Part 2: Enclosed Simple Low-Rise Buildings #4.…

A: Enclosed building Exposure C in all directions Mean roof height = 10.85m Design pressure at 9m L =…

Q: Calculate the fan power if the average pressure drop m 0.6 in, H2O, and the fan/motor efficiency is…

A: The given data is shown below: Pressure drop=0.6 in. H2OFan efficiency=70%Discharge=800,000…

Q: Air enters a junction in a duct with a volume flow rate of 2000 ft3/min. Two square duct branches,…

Q: The average weather conditions are; = 100 W/square meter = 25 deg. C = 55% = 2.7 m per sec = 2…

A: Solution:- Given data,

Q: The sizes of the soil stack and the vent pipe required to service 80 DFU's, with a total developed…

Q: According to the NBCC 2015, a building with multiple windows and doors with a non-uniform…

Q: 1. On a particular day, the wind speed is 2 m/s at a height of 10 m. Estimate the wind speed at…

A: Since we order one question at a time so we will answer the first one. please upload another…

Q: A stack in an urban area is emitting 80 g/s of NO. It has an effective stack height of 100 m. The…

A: Given:- The emission of NO by a stack in an urban area = 80 g/s The effective stack height = 100 m…

Q: A fixed-bed carbon adsorption system consisting of two 8-foot-deep beds containing 6 x 16 mesh…

A: Consider the given data As we know that power of the fan motor is given by the expression

Q: Water flows in a river. At 8 a.m. the flow past bridge 1 is 2150cfs. At the same instant the flow…

Q: Determine the required FRP duct diameter assuming a duct velocity (Uduct) of 2,000 ft/min, and an…

A: Given: The duct velocity is 2000 ft/min. The actual air emission rate is 15300 ft3/min.

Q: Calculate the precipitable water, the volume generated by the precipitation, and the height of…

A: Given data- Column of dry air 10km high Area (A) = 13 m2 Surface pressure is 101,300 Pa. The surface…

Q: Wind blows on the side of a fully enclosed hospital located on open flat terrain where V = 120 mi/h.…

A: V = Wind velocity= 120 mi/hh = Windward height = 30 ft

Q: Water flows through the 80-mm diameter pipe, head loss from A to B is hu = 0.5 m. Set datum, z = 0,…

A: Given, Diameter of the pipe (d) = 80 mm Head loss from A to B (hL) = 0.5 m Datum, z = 0 at B

Q: A wooden flume (n=0.012) of rectangular cross section is 2 ft wide. The flume carries 3 ft3/sec of…

Q: The water demand required to serve .820-ft wsfu is 170 gpm True False O

A: From graph of wsfu (water supply fixture units) vs water demand (GPM), For 500 wsfu water demand is…

Q: The diameter of the gutter sloped at 1/100 and required to drain a rain water from 480 m² roof, for…

A: Lets select pvc pipe with mannings coefficient (n) = 0.009 A(Area of roof) = 480m2 I (rainfall…

Q: step and short answer 1. A power plant emits SO2 at the rate of 110 g/s from a stack. If the…

A: The given data is: The rate of SO2 emission from stack, Q1=110 g/s The physical height of stack,…

Q: A wind loading creates a positive pressure on one side of the chimney and a negative (suction)…

A: Given :- A wind loading creates a positive pressure on one side of the chimney and a negative…

Q: 10- A stack in an urban area is emitting 100 g/s of NO. It has an effective stack height of 80 m.…

A: To find a) Ground level concentration at 3km downwind on the centreline. b) Ground level…

Q: The enclosed building shown in the photo and in Fig. 1-14a is used for storage purposes and is…

Q: as y 55%; and wind speed. per day using the energy r %3D hod. Assume standard at

Q: A jet of water issues out from a fire hydrant nozzle fitted at a height of 3 m from the ground at an…

Q: Q3: A// List a summery for the components of Nuclear power plant. B// The power delivered by the…

Q: A windmill is operating in a 10m/s wind that has a density of 1.2kg/m3. The diameter of the windmill…

A: Given operating wind= 10m/s density =1.2kg/m3 windmill diameter =4m upstream =3m downstream=4.5m…

Q: The unheated storage facility is located on flat open terrain near Sicilia Island, Italy. Determine…

A: Solution: As the value of snow load is not givenAssuming snow Load Pg=17 lb/ft2Slope of…

Q: Calculate the total collection area for a 98% efficient ESP that is treating 10,450 m2/min of air.…

A: Q=10450 m3/min w=6m/min To find collection area of ESP

Q: f) Which pitch angle would produce the greatest output from the wind turbine? 1- 15° 2- 30° 3- 45°…

A: Pitch angle- The angle between the wind turbine's longitudinal axis and the horizontal plane is…

Concept explainers

Thermal Processes

Some of the key areas where thermal processes find their application are:

Question

8. Determine the effective height of a stack needed to keep the maximum ground level ambient air
concentration below 10 ug/m³ from a source that emits 12 g/s of NQin a rural area with wind
speed 4 m/s measured at the stack height, and moderately stable air.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

A new municipal waste combustor burns 300 tons/day of waste and produces 100 dscf of emissions per lb of waste burned. The plant just meets the NSPS emission standards and has an effective stack height of 100 m and is located in a rural area. Under C stability and a windspeed of 4 m/s measured at 10 m, determine Cmax and xmax for (a) PM, (b) Pb in micrograms per cubic meter, and m, respectively
A fixed-bed carbon adsorption system consisting of two 8-foot-deep beds containing 6 x 16 mesh carbon operates at a superficial gas velocity of 60 ft/min. Specify the horsepower of the fan motor for the 15,000-cfm system if the total pressure drop across the system excluding the pressure drop across the bed is 5 in H2O.
1. In undisturbed air stream, where the pressure is 14.7 psi and density is 101325Pa, where the velocity is 500 ft/sec. What are the density, temperature, speed of sound, and specific weight where the velocity is 590ft/sec? g=9.8066 m/s^2
A jet of water issues out from a fire hydrant nozzle fitted at a height of 3 m from the ground at an angle of 45 degrees with the horizontal. If the jet under a particular flow condition strikes the ground at a horizontal distance of 20.17 m from the nozzle, find the jet velocity and the maximum height the jet can reach and its maximum horizontal distance from the nozzle. Neglect air resistance.
Air at 20°C and approximately 1 atm fl ows through asmooth 30-cm-square duct at 1500 ft3/min. The expectedpressure drop per meter of duct length is(a) 1.0 Pa, (b) 2.0 Pa, (c) 3.0 Pa, (d) 4.0 Pa, (e) 5.0 Pa
A wind tunnel has an inlet section with a velocity of 360 ft/s at standard atmospheric conditions. The airflow moves towards the throat, and the pressure decreased to 2010 lbs/ft^2. What is the velocity at the throat? * a. 704 ft/s b. 304 ft/s c. 403 ft/s d. 470 ft/s
A steam generator with economizer and air heater has an over all draft loss of 21.78 cm of water. If the stack gases are at 177C and if the atmosphere is at 101.3 kPa and 26C. What is the theoretical height of the stack in meters? Assume that the gas constant for the flue gases is the same as that for air
Predict the pressure drop for a full-scale haghouse after 30 mi mites of operation on an fiirstream with a dust loading of 30 gr/ft3 and an air-to-cloth ratio of 3.0 it/min.
Sulfur dioxide is being emitted in a rural area at a rate of 0.90 kg/s from a stack with an effective height of 220 m. The average wind speed at a stack height is 4.8 m/s and the stability category is B. Determine the short time period, downwind, centerline concetrration in micrograms per cubic meter at ground level distances from the stack of (a) 0.6 and (b) 0.8 km.
The difference in energy grade line between inlet and outlet is 20 cm when Ethyl Alcohol (specific gravity = 0.79 and viscosity = 1.19 x 10-3 Pa.s) is flowing under laminar conditions through a 5 m long horizontal pipe of 5 cm diameter. The flow rate (in m3/s) is most nearly? laminar conditions: Re<2,000 Re=(density*V*d)/(viscosity)=(density*(Q/A)*d)/viscosity
Determine the required FRP duct diameter assuming a duct velocity (Uduct) of 2,000 ft/min, and an actual air emission rate (Qa) of 15,300 acfm.
The Bourns building has several large exhaust stacks that can be seen fromground level. Assume an average wind speed of 1.0 m/s, neutral buoyancy of theexhaust plume, that the top of Bourns hall is 12 m from ground level and the topof the exhaust stacks are 20 m from ground level. What percent reduction in themaximum concentrations of the pollutants released from the building occur(compare with and without stack)? Assume rural stability class B for yourcalculations.