The link shown in the figure is pin-connected at A and rests against a smooth support at B. Draw the free-body diagram for the link and use it to compute the horizontal and vertical components of the reaction at pin A. Neglect the weight of the link. В 30° 0.75 m 90 N m 1 m 0.5 m 60 N

The link shown in the figure is pin-connected at A and rests against a smooth support at B. Draw the free-body diagram for the link and use it to compute the horizontal and vertical components of the reaction at pin A. Neglect the weight of the link. В 30° 0.75 m 90 N m 1 m 0.5 m 60 N

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Answer the The Average,Volts

A: We will solve this question in step no. 2

Q: Determine the area (m2) required for a new landfill site with a projected life of 10 years for a pop...

Q: 1. Calculate the plastic modulus of this section about y-y axis.

Q: cal curve with a length of 260 m is used to connec ion 1035.3 m. ocation of the highest point on thi...

Q: Design a 1 way slab to carry a live load of 4.8 KPa on a simple span of 4.50 m. Use f'c = 20.70 MPa,...

A: A one way slab is characterized for elements of the book as a flexural part with thickness little co...

Q: A portal frame ABCD consists of columns AB and CD of heights 3 m and 4 m respectively. While the bea...

Q: The rigid horizontal bar ABC of negligible mass is connected to two rods as shown in the figure. If ...

Q: For the retaining wall given below, what will be the active thrust acting per unit width of the wall...

A: Given data,

Q: A rectangular channel 2.5 m wide carries water at a depth of 1.2 m. The bed slope of the channel is ...

Q: A 6 m. x 9 m. rectangular foundation carrying a uniform load of 288 kPa is applied to the ground sur...

A: The stress distribution is the stress at any point below the ground surface due to the externally ap...

Q: 1. A 2 hr. UH is shown below Time (hr.) Discharge (m³/sec.) 1 2 15 3 12 4 10 5 If a storm of 4.2 cm....

A: Given 2hr UH Effective rainfall is equal to total rainfall - loss.

Q: 2.13 For a normally consolidated clay layer, given: Thickness = 3.7 m Void ratio 0.82 Liquid limit =...

Q: A tank initially holds 100 gallons of salt solution in which 50 tbe of salt has been dissolved. A pi...

Q: The specific energy in m- expressed by V=2.22 m/sec and y = 1 m is a) 1.25 b) 2.22 c) 3.22 d) 4.22

Q: Calculate the weaving ratio for the legs 1 and 2 out of the four legs rotary intersection mentioned ...

A: Given data,

Q: Given the existing components of each reaction with load P = 100 N. Determine the following: a.) The...

Q: A rectangular channel 2.5 m wide carries water at a depth of 1.2 m. The bed slope of the channel is ...

Q: Give me some sample problem with solutions with by using this formula in UNSTEADY RADIAL FLOW IN UNC...

A: Brief concept introduction- UNSTEADY RADIAL FLOW IN CONFINED AQUIFERS- In this case, we use the belo...

Q: The first cost of a machine is Php 1,800,000 with a salvage value of Php 300,000 at the end of its s...

Q: Problem 01 Using ASD, check the adequacy of the base plate (PL400X350×19 mm) centered on a W12X152 c...

A: Given data Base plate dimensions PL = 400 x 350 x 19 Concrete pedestal = 450 mm x 400 mm Column W 1...

Q: A rectangular channel 2.5 m wide carries water at a depth of 1.2 m. The bed slope of the channel is ...

Q: The two cylinders shown are identical and weighs 1000 N. The inclined smooth surface is 33° from the...

A: To Determine Reaction at point A

Q: 11. The reaction of a cable is always a tensile force. True False 12. Moment of inertia has no physi...

A: Answer 11 : true Answer 12 : false More explanation is given below.

Q: A vertical curve with a length of 260 m is used to connect a 2.5 % and -2.5 % gradients with a F ele...

Q: . Design a tubewell to deliver 33,000 gallons per hour at a depression head of 5 m. The average wate...

Q: I. A shallow continuous foundation is to be constructed on a soil under the ground' surface as shown...

Q: WHAT ARE THE SIGNIFICANT DIFFERENCES BETWEEN THE 3 KINDS OF PERSPECTIVE. One point perspective Two ...

Q: pls answer ASAP, I'll rate. Thank you so much. Using the Method of consistent deformation determine...

Q: aw the NFD, SFD, BMD for the following beams: 50 kN 10 kN/ m 3m 4 m

Q: A tensile load of 190 kN is applied to a round metal bar with a diameter of 16 mm and a gage length ...

Q: A steel girder 27 feet long is to be moved on rollers along a passageway 8 feet in width and into a ...

A: Given- Steel girder length = 27 feet Passageway 8 feet in width The horizontal width of the girder i...

Q: Determine the maximum bending stress on the section.

Q: ean sea lev ne MSL, the

A: base length at MSL L0 = 1500m altitude of runway = 300m above MSL find the length of the runway ?...

Q: A reinforced concrete T-Beam with bf = 850 mm, d = 300 mm, bw = 200 mm, t = 100 mm, f’c = 20.7 MPa a...

Q: Given data : Weight of dry soil=30 KN Weight of wet soil-D40 KN Volume of soil=20 m3

Q: he angular acceleration of the horizontal bar BD and (b) the ang 6V3 in 30

Q: Determine the value of concentrated load that must be placed at the crown of a two hinged parabolic ...

Q: A vertical curve with a length of 260 m is used to connect a 2.5 % and elevation 1035.3 m. The locat...

A: High point is from PVC:=g1g2-g1L2.5%2.5%--2.5%260m=2602=130m

Q: 16" 28" #3 3 #9 stirrups Bars

Q: Fast

Q: A bracket plate connected to a column flange transmits a load of 250 kN as shown in the figure. The ...

A: Given data, Load transmits a load of 250 kN

Q: The rigid bars ABC and CD are supported by pins at A and D and by a steel rod at B. There is a rolle...

A: Given data, E = 200 GPa A = 300 mm² L = 3 m Load = 50 kN To find out the vertical displacement of p...

Q: For the figure shown below having a simply supported beam with an applied load on it, what will be s...

Q: ituation 1 | A built-up beam made from fastening two channels to a wide flange section car pads` as ...

A: The I Section is symmetrical with respect to both X and Y Axes. X = ∑Ai Xi /∑Ai = 210 / 2 = 105 mm Y...

Q: The three consecutive readings taken from a level are 1.325 m, 0.985 m and 2.546 m. If the instrumen...

Q: 2. A 3.7-m high by 1.5-m wide rectangular gate AB is vertical and is hinged at a point 150 mm below ...

Q: Determine the force in each member of the truss. State whether the members are in tension or compres...

Q: A 40 SITUATION 6

Q: A slope of infinite extent with a slope angle of 22° is made of a soil having c = 0 and angle of int...

Q: A sand layer of the cross-sectional area shown in the figure has been determined to exist for a 500 ...

A: Q=KiA i= H/L I=(160-150)/125 A=2×500 = 1000m2 K=3m/day

Concept explainers

Equilibrium and Support Reactions

Civil engineers deal with structures that are composed of several members connected or with individual members such as beams and columns. To analyze such structures, the condition of statics must be applied. Under the static condition, the members are considered to be in equilibrium under the action of forces, that is, the members are assumed to be having negligible velocity.

Question

8. The link shown in the figure is pin-connected at A and rests against a smooth support at B.
Draw the free-body diagram for the link and use it to compute the horizontal and vertical
components of the reaction at pin A. Neglect the weight of the link.
В
30
0.75 m
90 N· m
0.5 m
60 N

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Block B weighs 200N and block C weighs 100N. See Figure4. Determine the weight of block D and the required angle θ for equilibrium
The support B of the structure shown in Figure settled by 0.7 in. Determine all reactions using slope-deflection equations. Use E = 30,000 ksi and I = 240 in4.
A trough is filled with a liquid of density 8232 N/m^3. The ends of the trough are equilateral triangles with sides 8m long and vertex at the bottom. Set-up the integral for the force on one end of the trough.
The 4-in.-diameter shaft is held in the hole such that the normal pressure acting around the shaft varies linearly with its depth as shown. Determine the frictional torque that must be overcome to rotate the shaft. Take μs = 0.2.
T (Shear force) and M (Bending) for the system whose loading condition is given in Figure 1.Draw the moment diagrams. Calculate the deflection (vertical displacement) at point B in mm using Castigliano's Theorem. The beam bending stiffness (EI) is constant along the bar and its value is 50 000 kNm2. q=1,4(kN/m) a=8(m) El=50000(kNm2)
The surface AB is quarter a sphere that is hinged at B, and held by a horizontal force P at A. All dimensions are on the figure.gamma=9810 N/m^3a) Find the vertical reaction, By, at point B.b) What force P is required for equilibrium.c) Find the horizontal reaction, Bx, at point B
Determine the angle θ for equilibrium of the lever shown in the figure. Disregard the weights of bars AB and BC.
Situation 11. The uniform 14-ft pole weighs 150 lb and is supported as shown. 22. Calculate the force P required to move the pole if the coefficient of static friction for each contact location is 0.40. a. 157.92 lb b. 18.48 lb c. 93.6 lb d. 143.52 lb 23. Determine the reaction at B in lb. a. 82.8 b. 25.2 c. 89.2 d. 27.1
The continuous beam shown in the figure is fixed at both ends A and D, and supported by rollers at B and C Assume I = 800 x 106 mm4 and E = 70,000 MPa. W1 (kN/m) = 25 F (kN) = 50 S (mm) = 15 If there is a settlement of S at the support C, solve the following: 1. Slope at B, in radians 2. Slope at C, in radians 3. Reaction at A, RA in kN 4. Moment at A, MA in kN-m 5. Reaction at D, RD in kN 6. Moment at D, MD in kN-m
The 1-m diameter cylinder in the figure is 8 meters long (dimension perpendicular to the paper) and rests in static equilibrium against a frictionless wall at B. Draw the free-body diagram of the cylinder and calculate the horizontal reaction at B.
The force 650N is the resultant of the forces P and 300N acting as shown in the figure. At what angle does the 500N makes with the horizontal?
Please show complete solutions. Considering EI is constant and the value of P is 425kN, calculate the following using Conjugate beam method : A. What is the value of the reaction at point B in the real beam? B. What is the value of the reaction at Point A in the conjugate beam? C. DISPLACEMENT AT C. D. DETERMINE SA SLOPE AT B.