What is the net torque about on the bar shown in (Figure 1) about the axis indicated by the dot? Suppose that o = 70° and 0 = 30Express your answer with the appropriate units.T= 5.507N/mEnter your answer with a different unit type. Review a list of acceptable units.No credit lost. Try again.Figure< 1 of 1>SubmitPrevious Answers Request AnswerNext>Provide Feedback8.0 N10N25 cm75 cm

Answered: 8.0 N 10 N 25 cm 75 cm

Science

Physics

8.0 N 10 N 25 cm 75 cm

College Physics

1st Edition

ISBN:9781938168000

Author:Paul Peter Urone, Roger Hinrichs

Publisher:Paul Peter Urone, Roger Hinrichs

Chapter10: Rotational Motion And Angular Momentum

Section: Chapter Questions

Problem 15PE: Consider the 12.0 kg motorcycle wheel shown in Figure 10.38. Assume it to be approximately an...

See similar textbooks

Similar questions

Answer yes or no to the following questions. (a) Is it possible to calculate the torque acting on a rigid object without specifying an axis of rotation? (b) Is the torque independent of the location of the axis of rotation?
A soccer player extends her lower leg in a kicking motion by exerting a force with the muscle above the knee in the front of her leg. She produces an angular acceleration of 30.00 rad/s2 and her lower leg has a moment of inertia of 0.750kg-m2 What is the force exerted by the muscle if its effective perpendicular lever arm is 1.90 cm?
A rigid body is rotating counterclockwise about a fixed axis. Each of the following pairs of quantities represents an initial angular position and a final angular position of the rigid body. Which of the sets can occur only if the rigid body rotates through more than 180? (a) 3 rad, 6 rad; (b) 1 rad, 1 rad; (c) 1 rad, 5 rad.
What three factors affect the torque created by a force relative to a specific pivot point?
A solid cylinder of radius 10.0 cm rolls down an incline with slipping. The angle of the incline is 30 . The coefficient of kinetic friction on the surface is 0.400. What is the angular acceleration of the solid cylinder? What is the linear acceleration?
Suppose you start an antique car by exerting a force of 300 N on its crank for 0.250 s. What angular momentum is given to the engine if the handle of the crank is 0.300 m from the pivot and the force is exerted to create maximum torque the entire time?
Suppose a child gets off a rotating merry-go-round, Does the angular velocity of the merry-go-round increase, decrease, or remain the same if: (a) He jumps off radially? (b) He Jumps backward to land motionless? (c) He jumps straight up and hangs onto an overhead tree branch? (d) He jumps off forward, tangential to the edge? Explain your answers. (Refer to Figure 10.34).
CHECK and THINK Our results give us a way to think about how a person might steer a unicycle. Consider the person, the unicycle, and the Earth as the system. No net torque acts on the system. Ignoring the motion of the Earth, Figure 13.37A shows the initial angular momentum of the system with the unicycle in motion: Li=Ltire. The person leans to his left so that the angular momentum of the tire rotates downward. The total angular momentum must still point to the right (Fig. 13.37B), so the angular momentum of the person must be upward to compensate. The persons angular velocity therefore points upward (parallel to his own angular momentum), and he is able to make a turn. Another way to analyze this situation is to exclude the Earth from the system and calculate the torque done by gravity. This approach is left as a homework problem. FIGURE 13.37 C Reanalyze the unicycles motion in Example 13.15 (page 382). This time, leave the Earth out of the system and explain how the torque exerted by gravity causes the unicycle to turn. Your explanation should involve a diagram.
What are the necessary conditions for equilibrium of the object shown in Figure P12.1? Calculate torques about an axis through point O.
Starting with the formula for the moment of inertia of a rod rotated around an axis through one end perpendicular to its length (I=Ml2/3) , prove that the moment of inertia of a rod rotated about an axis through its center perpendicular to its length is I=Ml2/12 . You will find the graphics in Figure 10.12 useful in visualizing these rotations.
Two forces F1 and F2 act along the two sides of an equilateral triangle as shown in Figure P11.5. Point O is the intersection of the altitudes of the triangle. (a) Find the magnitude of a third force F3 to be applied at B and along BC that will make the total torque zero about the point O. (b) What If? Will the total torque change if F3 is applied not at B but at any other point along BC? Figure P11.5
A pulley of moment of inertia 2.0kgm2 is mounted on a wall as shown in the following figure. Light strings are wrapped around two circumferences of the pulley and weights are attached. What are (a) the angular acceleration of the pulley and (b) the linear acceleration of the weights? Assume the following data: r1=50cm , r2=20cm , m1=1.0kg , m2=2.0kg