Answered: 8(x) Boundary layer'

Engineering

Mechanical Engineering

8(x) Boundary layer'

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter5: Analysis Of Convection Heat Transfer

Section: Chapter Questions

Problem 5.29P: Air at 20C flows at 1 m/s between two parallel flat plates spaced 5 cm apart. Estimate the distance...

See similar textbooks

Related questions

Q: 7. A flat plate has a length of 40 cm and width of 1 m. Air, at pressure of 2 atm, temperature of 57…

Q: 1. What is Reynold's number? 2. State some practical examples of laminar and turbulent flow? 3.…

A: Flows with low Reynolds numbers tend to be laminar, while those with high Reynolds numbers tend…

Q: A boat moves through water (T = 40°F), at 18.0 mi/h. A flat portion of the boat hull is 3.3 ft long,…

A: The properties of water at T = 40 oF are written as, The velocity of the boat is given as, The…

Q: Assume the stabilizer of an airplane is a flat plate. If the transition /critical RN 750,000, what…

A: Given:- RN=750000 Chord=0.81m v=44.7 m/s2 Rectangular span:=1.73m To find:- Drag

Q: Water flows at a velocity of 1.2 m/s over a flat plate 1.2 m long. Assume 1/7th power law and…

Q: In order to avoid boundary layer interference, engineers design a “boundary layer scoop” to skim off…

Q: Consider again a semi truck traveling at 55 mph on the freeway. The ambient air is at 1 atm and…

Q: 6. During a winter day, wind at 70 km/h, 5°C, and 1 atm is blowing parallel to a 4-m-high and 15…

Q: The boundary layer formed as turbulent around the sphere is when ReD = 2.5*10^5 (a) Golf…

A: Re= 2.5×105Golf ball diameter, Dg= 43 mm= 0.043 mSoccer ball diameter, Ds= 222 mm= 0.222 m Note:…

Q: 3435 E1 (B) Air at 27°C flows over a flat plate with a velocity of 3 m/s. Calculate the boundary…

Q: What is the f (equivalent drag area) for an aircraft that creates 600 lbs of parasite drag at 10,000…

A: Write the density of air at an altitude of 10000 ft. ρ=0.0565 lbs/ft3

Q: Two definitions of displacement thickness are given in this chapter. Write both definitions in your…

Q: A 5,000 lb airplane with wing area of 250 sq. ft and power available of 450 hp is at sea level…

A: Please find the answer below

Q: Derive an expression for turbulent boundary layer thickness over a flat plate

A: Given A turbulent flow in a flat plate To find Turbulent boundary layer expression

Q: The 2013 Toyota Camry has an empty weight of 3190 lbf, a frontal area of 22.06 ft2, and a drag…

A: Write the given value using suitable variables. Here W signifies Camry weight, A signifies frontal…

Q: One dimension of a rectangular flat plate is twice the other. Air at uniform speed flows parallel to…

A: Understand the characteristic length of the plate will be that length that is parallel to the…

Q: Which one of the following is not a flow region where the boundary layer approximation may be…

A: In the flows mentioned above, (a) The jet has a boundary layer in its circumferential region. There…

Q: For flow along a flat plate with x being the distance from the leading edge, the boundary layer…

A: Step 1 The boundary layer thickness for flat plate is represented by the following expression:…

Q: Explain boundary layer thickness?

A: Boundary layer thickness is described as a vertical distance from the boundary up to the point where…

Q: Fairings are attached to the front and back of a cylindrical body to make it look more streamlined.…

A: Drag forces arise from pressure differences over the body (due to its shape) and frictional forces…

Q: Consider again a semi truck traveling at 55 mph on the freeway. The ambient air is at 1 atm and 80F.…

A: Write the formula for Reynolds number. Re=VLν Here, Re is the Reynolds number, V is the velocity of…

Q: 2. Water flows at a velocity of 1.2 m/s over a flat plate 1.2 m long. Assume 1/7th power law and…

Q: Assume that the Flettner rotor ship of Fig. has a waterresistance coefficient of 0.005. How fast…

A: Given data Height of the rotor L = 50ftDrag coefficient of te rotor CD = 4Lift coefficient of each…

Q: During a winter day, wind at 70 km/h, 5°C, and 1 atm is blowing parallel to a 4-m-high and 15-m-long…

A: Velocity of wind = 70 km/h = 19.444 m/s The pressure of the air = 1 atm Length of the wall = 15m…

Q: Question 18 A turbulent boundary layer stays attached in a more adverse pressure gradient than the…

A: The hydrodynamic boundary is formed over a surface on which a fluid is flowing. This boundary layer…

Q: A commercial airplane has a total mass of 70,000 kg and a wing planform area of 150 m2. The plane…

A: Given, The mass of the plane, M=70000 kg Wing planform area, A=150 m2 Speed, V=558 km/h=558×518…

Q: A flat plate ( 1.5 m) long and ( 1.5 m) wide is towed in water ( p 1000 kg/m and v=1.31 * 10 “m² /s)…

Q: Light oil at 75°F flows over a 22-ft-long flat plate with a free-stream velocity of 6 ft/s.…

A: Given data: Length of plate, L = 22 ft Stream velocity, V = 6 ft/s Temperature, T = 75°F

Q: Ql: Explain and sketch the boundary layer over a horizontal flat plate, then write the equations…

A: ◆ In laminar region --> Velocity profile is parabolic. ◆ In turbulent region --> Velocity…

Q: Q.1 The velocity distribution in a turbulent boundary layer is given by 1/7 What is the displacement…

A: Write the expression of velocity distribution. uU=yδ1/7

Q: Water flows at a velocity of 1.2 m/s over a flat plate 1.2 m long. Assume 1/7th power law and…

A: Due to no slip condition at the hydrofoil surface, there develops a region where viscous effect…

Q: The sphere is dropped in gasoline at 20 ° C.Ignoring its acceleration phase, what will it's terminal…

A: For gasoline at 20°C, take ρ ≈ 680 kg/m3 and μ ≈ 2.92E−4 kg/ms. For steel take ρ ≈ 7800…

Q: 8. A flat plate ( 1.5 m ) long and ( 1.5 m ) wide is towed in water (p = 1000 kg/m and v=1.31 * 10 “…

A: The given values are length l=1.5m, width b=1.5m, density ρ=1000kg/m3 , kinematic viscosity…

Q: Explain briefly the advantages of using Von Karman Method in determining the boundary layer…

A: The Von Karman approximation makes it simple to find boundary layer parameters, and the benefits are…

Q: Prob.7. A smooth flat plate of length 5 m and width 2 m is moving with a velocity of 4 m/s in…

A: Given data- The length of the plate is L = 5 m. The width of the plate is w = 2 m. The velocity of…

Q: A portion of ship’s hull can be idealized as a flat plate, 100ft long. If the ship’s velocity is 10…

A: Given data: L=100 ftv=10 ft/sρ=62.4 lbm/ft³µ=3.0 lbm/hr.ft Need to determine the maximum boundary…

Q: 8. A flat plate ( 1.5 m ) long and ( 1.5 m ) wide is towed in water ( p = 1000 kg/m and v=1.31 * 10…

Q: a) A sphere (Case 1) is modified with a fairing at the back of sphere (Case 2) and a housing (Case…

Q: Light oil at 75°F flows over a 17-ft-long flat plate with a free-stream velocity of 5 ft/s.…

A: Given Data⇒Light oil atT=75°F=297.039 KLenght of plateL=17 ftFree stream velocityv=5ftsProblem…

Question

An aluminum canoe moves horizontally along the surface of a lake at 3.5 mi/h. The temperature of the lake water is 50°F. The bottom of the canoe is 20 ft long and is flat. Is the boundary layer on the canoe bottom laminar or turbulent?

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

In your own words, list at least three “red flags” to look out for when performing laminar boundary layer calculations.
Explain boundary layer thickness?
Answer the following. Must answer all the questions. Dont attempt partially. i. Description of external flow phenomena, ii. Effect of boundary layer theory on external flow iii. Explanation of Reynold’s number and its significance on external flow studies.
In order to avoid boundary layer interference, engineers design a “boundary layer scoop” to skim off the boundary layer in a large wind tunnelFig. . The scoop is constructed of thin sheet metal. The air is at 20°C, and flows at V = 45.0 m/s. How high (dimension h) should the scoop be at downstream distance x = 1.45 m?
Mention the name of a technique which can be used to control the boundary layer
Which one of the following is not a flow region where the boundary layer approximation may be appropriate? (a) Jet (b) Inviscid region (c) Wake (d ) Mixing layer (e) Thin region near a solid wall
For flow along a flat plate with x being the distance from the leading edge, the boundary layer thickness grows like (a) x (b) √x (c) x2 (d ) 1/x (e) 1/x2
A portion of ship’s hull can be idealized as a flat plate, 100ft long. If the ship’s velocity is 10 ft/s and the properties of the water it is moving through are ρ=62.4lbm/ft³ and µ=3.0lbm/hr.ft, calculate the maximum boundary layer thickness.
Air flows parallel to a speed limit sign along the highway at speed V = 8.5 m/s. The temperature of the air is 25°C, and the width W of the sign parallel to the flow direction (i.e., its length) is 0.45 m. Is the boundary layer on the sign laminar or turbulent or transitional?
7. A flat plate has a length of 40 cm and width of 1 m. Air, at pressure of 2 atm,temperature of 57 C, and velocity of 3 m/s flows over the plate. Find the thicknessof the boundary layer at x = L.
A boat moves through water (T = 40°F), at 18.0 mi/h. A flat portion of the boat hull is 3.3 ft long, and is treated as a simple smooth flat plate boundary layer, to first approximation. Is the boundary layer on this flat part of the hull laminar, transitional, or turbulent? Discuss.
Boeing 737-600 flies at altitude 150o0m above sea level with speed 85 m/s and total drag coefficient equal to (0.075). Find the drag force at this fly condition. Given data /R=287, g=9.81 m/s2, po=0.3648 kg/m2 and wing area 135m^2*