9-6. Determine the normal stress and shear stress acting on the inclined plane AB. Solve the problem using the method of equilibrium described in Sec. 9.1. 9-7. Determine the normal stress and shear stress acting on the inclined plane AB. Solve the problem using the stress transformation equations. Show the result on the sectioned element. 45 MPa 45 80 MPa

9-6. Determine the normal stress and shear stress acting on the inclined plane AB. Solve the problem using the method of equilibrium described in Sec. 9.1. 9-7. Determine the normal stress and shear stress acting on the inclined plane AB. Solve the problem using the stress transformation equations. Show the result on the sectioned element. 45 MPa 45 80 MPa

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A 5-m STEEL SHAFT ROTATING AT 2Hz HAS 70 KW APPLIED AT GEAR THAT IS 2m FROM THE LEFT END WHERE 20 KW ARE REMOVED.AT THE RIGHT END, 30KW ARE REMOVED AND ANOTHER 20 KW LEAVES THE SHAFT AT 1.5m FROM THE RIGHT END. (A) FIND THE UNIFORM SHAFT DIAMETER SO THAT THE SHEARING STRESS WILL NOT EXCEED 60 MPa. (B) IF A UNIFORM SHAFT DIAMETER OF 100mm IS SPECIFIED, DETERMINE THE ANGLE BY WHICH ONE OF THE SHAFTS LAGS BEHIND THE OTHER END. USE G = 83 GPa.
A rectangular plane, 1.2 m by 1.8 m is submerged in water and makes qn angle of 30° with the horizontal, the 1.2 m sides being the horizontal. a. what is the minimum lressure acting on the plane in kPa b. what is the maximum lressure acting on the plane kPa c. Determine the magnitude of hydrostatic force acting on either side of the plane in KN. Support your computations with correctly drawn and labrled pressure prism diagrams.
A shaft 100mm in diameter and 3m long, with bult-in ends, is subjected to a clockwise torque of 4KN-m applied 1m from the left end, and to another clockwise torque of 16 KN-m applied 2m fromthe left end. 16. Compute for the shearing stress at segment AB. A. 61.12 MPa B. 20.37 MPa C. 40.74 MPa D. 30.30 MPa 17. Compute for the shearing stress at segment BC. A. 61.12 MPa B. 20.37 MPa C. 40.74 MPa D. 30.30 MPa 18. Compute for the shearing stress at segment CD. A. 61.12 MPa B. 20.37 MPa C. 40.74 MPa D. 30.30 MPa
1. If the T-beam is subjected to a vertical shear of V = 12kip, determine the maximum shear stressin the beam. Also, compute the shear-stress jump at the flange-web junction AB. Sketch thevariation of the shear-stress intensity over the entire cross-section.
H.W The uniform thin pole has a weight of 50 N and a length of 26m. If it is placed against the rough wall and on the rough box in the position d= 10 m, us =0.3 at points A, B and C P= 150 N Box weight= 100N Determine the distanice x when the motion of the pole impend
Please determine: a.)the head loss for the bend b.) the magnitudes and directions of the forces anchoring the pipe bend in place, Rx and Ry
The copper pipe [G = 5,000 ksi] has an outside diameter of 3.500 in. and a wall thickness of 0.250 in. The pipe is subjected to a uniformly distributed torque of t = 85 lb-ft/ft along its entire length. Using a = 2.5 ft, b = 3.5 ft, and c = 8.0 ft, determine(a) the maximum shear stress in the pipe.(b) the rotation angle φC at the free end of the shaft.
The cantilever beam is subjected to a concentrated load of P=20kips. The cross-sectional dimensions of the rectangular tube shapre are b=5.2in , d=8.10in , and t=0.400in. Determine:a) The magnitude of the maximum horizontal shear stress in the rectangular tube shape. Answer in ksi, rounded-off to 2 decimal places.b) The magnitude of the shear stress at point K, which is loacted to the left of the vertical centroidal axis zK=1.1in. Answer in ksi, rounded off to 2 decimal places.
An equilateral triangular plate of side 2.4m placed horizontally in a liquid (sp. gr. 0.80) in such a way that the center of the plate is 2.5m below the free surface of water. (a) Determine the area (in sq. meters) of the plate. (b) Determine the magnitude (in kN) of the resultant force on the plate.
Compute the value of EIy at 2.5 m from the left support.
Questions b and c. The pressure from part a is 0.86832 Mpa
Solve for support rections at A, B and C