9 ft- Problem 3. The frame that supports the 1000 lb anvil consists of members ABCDE, A 3 t B 1 ft CFG, and DF; the pulley with center G; and the cable. Determine: (a) the forces that pins C, F, and G exert on member CFG; (b) the forces that pins B, C, and D exert on member ABCDE; and (c) the reactions that pin A and roller E exert on member ABCDE. C 3 ft 3 t E

9 ft- Problem 3. The frame that supports the 1000 lb anvil consists of members ABCDE, A 3 t B 1 ft CFG, and DF; the pulley with center G; and the cable. Determine: (a) the forces that pins C, F, and G exert on member CFG; (b) the forces that pins B, C, and D exert on member ABCDE; and (c) the reactions that pin A and roller E exert on member ABCDE. C 3 ft 3 t E

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Thumbs-Up will be given. Write the complette solutions legibly. Answer in 3 decimal places. Please answer all since they are all subquestions. Thanks Structural Theory 1d. Determine the vertical reaction R₂ in kN 1e. Determine the shear at midspan between vertical supports in kN. 1f. Determine the maximum factored load moment in the beam in kN.m
Two d mm*10 mm cover plates are welded to two UPN 200 channels 100 mm high to form the cross section of the compound beam shown in the figure. The moment of inertia of each channel about a horizontal axis through the centroid is 19.10*106 mm4. a) Determine the support reactions. b) Draw the shear force and bending moment diagrams. c) If the allowable bending stress of the beam is 300 MPa, find the required width d of the plates to safely support the load.
The Channel section is used as a purlin placed on top of trusses with spacing of 4 m and slope 1V to 4H. The purling are supporting a total uniform load of 24 kN/m. Properties of Channel: Sx = 119 x 10^3 mm^3 Sy = 87 x 10^3 mm^3 Compute the maximum bending stress if supported by sagrods at third points. Round your answer to 2 decimal places.
Uniform slender bar ABC of mass m = 5 kg and length L = 3m is pinned at A and supportedby a cable attached at B. The cable runs over a frictionless pulley at E, but the small pulley at Dhas seized and will not rotate; the coefficient of static friction between the cable and the seizedpulley at D is 0.2. The pulley at E supports a cylinder of mass M. Find the mass M required toinitiate counterclockwise (CCW) rotation of bar ABC. α = 30o and θ = 25o.
7.3 The jib crane supports a load of F = 710 lb from the trolley which rides on the top of the jib. Determine the internal normal force, shear force, and moment in the jib at point C when the trolley is at the position shown. The crane members are pinned together at B, E and F and supported by a short link BH. Determine the internal normal force at point C. Determine the shear force at point C.
Determine the magnitude of the moment of force F about segmentOA of the pipe assembly shown.
Two 160 mm * t cover plates are welded to two cahnnels 200 mm high to form the cross section of the beam shown in the figure. The moment of inertia of each channel about a horizontal axis through the centroid is 2.06*106mm4. a)Determine the support reactions. b)Draw the shear force and bending moment diagrams. c)If the allowable bending stress of the beam is 255 MPa, find the required thickness t of the plates to safely support the load.
The beam is subjected to a load F = 300 Nand is supported by the rope and thesmooth surfaces at A and B.a. Draw the free-body diagram of thebeam.b. What are the magnitudes of thereactions at A and B?
2. The beam AB shown is supported at A and B. the beam is loaded with three fixed concentrated loads and an overhead hoist carrying a load W. P1 P2-320 KN. P3-200 KN and W-500 KN A. Find the distance of W from A in meters if the resultant of the external loads is at the midspen B. What is the reaction at A when W is at midspan?
A) Define the bending stress as relates of beams. B)A fixed AB length 3m carries a point load of 45KN at a distance of 2m from A.if the flexural rigity (i.e. EL)is 1×10^4KNm^2, determine: I) fixed end moment A and B II) Deflection under the load III) the maximum deflection IV) The position of the maximum deflection.
If a 100-N force is applied to the handles of the pliers, determine the clamping force exerted on the smooth pipe B and the magnitude of the resultant force that one of the members exerts on pin A.
A 5.0m simple beam supports the given floor loads Wu and a concentrated load Pu due to the wall transverse to the given beam. Answer the following questions given the sections of the beam. Calculate the depth of the neutral axis of the section in PART B in mm.0 Calculate the stress in the steel of the section in PART B in MPa.0 Calculate the ultimate moment capacity of the section in PART B in kN.m.0