9. The net work done per engine cycle in a 4-stroke diesel internal combustion engine (as in the previous question) is 2550 J. The engine has 4 cylinders and the crank shaft rotates at 3520 revolutions per minute. The output power of this engine is 36.5 kW. Calculate: (a) the indicated power of the engine (b) The power dissipated due to frictional forces.

9. The net work done per engine cycle in a 4-stroke diesel internal combustion engine (as in the previous question) is 2550 J. The engine has 4 cylinders and the crank shaft rotates at 3520 revolutions per minute. The output power of this engine is 36.5 kW. Calculate: (a) the indicated power of the engine (b) The power dissipated due to frictional forces.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

For a Rankine cycle, increasing maximum temperature while holding all other parameters constant will allow an engineer to make the following statements Group of answer choices Quality at the turbine exit will decrease increasing liquid water content and causing turbine erosion. Quality at the turbine exit will increase and improve turbine durability. Increasing maximum temperature increases the average temperarture at which heat is added and will increase thermal efficiency Increasing maximum tempearture will decrease required mass flow rate for a specified power output.
1. Compare and evaluate the actual and ideal thermal efficiencies and back work ratio 2. Construct efficiency vs. pressure ratio plot, showing the region of typical values of gasturbine operating pressure ratios.3. What is the main limitation associated with turbine in a gas turbine power cycle.
30. A power producing equipment with a 4 cylinder, 4- stroke and operating in an air standard diesel cycle has a bore of 10cm and stroke of 12cm. Determine the engine displacement in each cycle. a. 7.5396Li b. 7.5399Li c. 7.5397Li d. 7.5398Li
What is the mechanical efficiency of a diesel engine if friction power is 30 KW and brake power of 150 KW?
For a Rankine cycle, decreasing minimum pressure while holding all other parameters constant will allow an engineer to make the following statements Group of answer choices The quality at the turbine exit will decrease increasing liquid water content and back stage turbine damage, Turbine net work output will increase due to the reduced pressure at the exit The quality at the turbine exit will increase improving turbine reliability The average temperature at which heat is rejected will increase increasing thermal efficiency
A spark- ignition engine operates on an Otto cycle with a compression ratio of 9 and a temperature limits of 30°C and 1000°C. If the power input is 500 kw, calculate the mass flow rate of air.
Quantitatively compare the Carnot Rankine cycle of (figure 1) with the ideal Rankine cycle (figure 2). – Calculate the efficiency for the two cycles – Calculate the work per unit mass (kJ/kg) for the two cycles (Woutput = W34 – W12); – Compare the efficiencies and work done by the two cycles
A 6.4-liter, V8 Spark ignition (8 cylinder) 4-stroke engine operates at an engine speed of 3200 RPM. The compression ratio is CR = 10.5:1. At this speed volumetric efficiency is 93%, combustion efficiency is 98%, indicated thermal efficiency is 47%, and mechanical efficiency is 86%. Stroke and bore will be related by S = 0.90 B. Combustion starts at 18 degrees bTDC and last for 0.25 seconds. Calculate? a.Overall efficiencyb. Piston displacementc. Cylinder bore and stroked. average piston speed and max piston speede.distance piston has traveled from TDC at the end of combustion, f. volume at the end of combustion g. position of crank at the end of combustion
A power cycle capable of delivering a power output of 410 kJ for an energy input by heat transfer of 1000 kJ. The system undergoing the cycle receives the heat transfer from hot gases at a temperature of 500 K and discharges energy by heat transfer to the atmosphere at 27 °C. Evaluate: 1 amount of aheat released from the system and thermal efficiency 2 the efficiency if the system operates in Carnot cycle. 3 draw the schematic diagram of the system.
Explore and illustrate the impact of the following power generation technologies on the environment , and their contributions on the energy market. (a) Coal, (b) Oli, (c) Gas, (d) Nuclear, (e) Wind,
Steam is the working fluid in the ideal Rankine cycle 1–2–3–4–1 and in the Carnot cycle 1–2–3’–4’–1 that both operate between pressures of 1.5 bar and 60 bar as shown in the T–s diagram in Fig. below. Both cycles incorporate the steady flow devices shown in Fig. For each cycle determine (a) the net power developed per unit mass of steam flowing, in kJ/kg, and (b) the thermal efficiency. Compare results and comment.
A two-stroke, 12-cylinder diesel engine with an effective power of 2440 kW at 550 rpmmanufactures. The cylinder diameter of the engine is 24 cm, the stroke length is 32 cm, the volumetric efficiency is 97% andSince its mechanical efficiency is 88%;a) Find the mass fuel flow entering the engine.b) Find the effective specific fuel consumption.c) Find the indicated specific fuel consumption.d) Calculate the motor torque.e) Calculate the mean indicated pressure.