90mm 60mm 90mm 90mm 60mm 90mm Since there is a pressure force P at point A, a tensile force of 2P at point B, and a pressure force of 4P at point C: a) Calculate the force P that the section will carry safely b) According to this calculated force, draw the normal stress distribution P in the section.

90mm 60mm 90mm 90mm 60mm 90mm Since there is a pressure force P at point A, a tensile force of 2P at point B, and a pressure force of 4P at point C: a) Calculate the force P that the section will carry safely b) According to this calculated force, draw the normal stress distribution P in the section.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The cross sectional area of the bar ABCD is 545 mm2F1 = 15 kNF2 = 20 kNF3 = 40 kNDetermine the normal stress in bar AB, BC, and CD & the maximum normal stress. Specify if answers are tension or compression.
1. Calculate the total length, L (m) so that the resulting stress, q is uniform. 2. Which of the following gives the location (m) of the maximum shear from the left end? 3. Which of the following gives the location (m) of the point of inflection from the left end?
The solid shaft is fixed to the support at C and subjected to the torsional loadings and axial load P as shown. a. Determine the torsional shear stress at Point A (50mm from the center) and Point B (on the Surface) b. Determine the absolute maximum torsional shear stress in the shaft. c. sketch the state of stress at point A and draw its corresponding Mohr’s Circle of stress. compute the principal stresses and maximum in-plane stress. T=10.38kN-m
The rod has a diameter of 40 mm. It is subjected to the force system Fx=1300 N=1300 N, Fy=500 N=500 N, Fz=800 N=800 N. Determine the normal stress that acts at point B. Determine the shear stress (τB)xy that acts at point B. Determine the shear stress (τB)xz that acts at point B.
Determine the average normal stress at section a-a and the average shear stress at section b-b in member AB. The cross-sectional is square, 0.55 in. On each side.
Very very Urgent The distributed load q and the singular moment M act on the stepped shaft given in the figure. Draw the cross-sectional influence diagrams of the system under these forces. Determine the maximum stress value for the critical section. L1 = 226 mm ,L2 = 118 mm, a = 159 mm M = 572 N.m, q = 5 N/mm D = 51 mm , d1 = 19mm , d2 = 5 mm
The shaft shown in (Figure 1) is supported by bearings at A and B that exert force components only in the x and z directions on the shaft. If the allowable normal stress for the shaft is σ allow = 15 ksi, determine the smallest diameter of the shaft that will support the loading. Use the maximum shear stress theory of failure. Take τ allow = 2.7 ksi.
The copper pipe [G = 7,000 ksi] has an outside diameter of 3.875 in. and a wall thickness of 0.250 in. The pipe is subjected to a uniformly distributed torque of t = 80 lb-ft/ft along its entire length. Using a = 2.5 ft, b = 4.0 ft, and c = 8.5 ft, determine(a) the maximum shear stress in the pipe.(b) the rotation angle φC at the free end of the shaft.
Find normal and shear stresses at point P
A hollow shaft shown with an outside diameter of 150 mm and an inside diameter of 130 mm is subjected to an axial tension load of P = 75 kN and torques TB = 16 kN-m and TC = 7 kN-m. 14. Calculate the polar moment of inertia of the section in mm4.1 15. Calculate the absolute value of the internal torque at H in kN.m. 16. Calculate the torsional shear stress at H in MPa. 17. Calculate the absolute value of the minor principal stress at point H in MPa. 18. Calculate the absolute value of the major principal stress at point H in MPa. 19. Calculate the absolute value of the maximum shear stress at point H in MPa. 20. Calculate the orientation of the principal axes in degrees. Kindly answer all numbers with complete solution
Two solid cylindrical rods (1) and (2) are joined together at flange B and loaded as shown. If F1 = 16 kips, F2 = 30 kips, and the normal stress in each rod must be limited to 18 ksi, determine the minimum diameter d1 required for rod (1).
solve for deformation in figure B. given V= 10-0 and area = 2.0in^2