TECHNICAL TERMS ENCOUNTERED IN DRAFTING ROOF PLANS 1. A horizontal structural member which hold the rafters together.a. Rafter b. Purlins2. A prefabricated triangulard. Runc. Riseshaped unit supporting the roof loadsover long spans.a. Trussb. Shinglesc. Rise3. The top edge of the roof where rafters meeta. Ridgeb. Rafterc. Overhang d. Purlinsthe top plate and the ridge board referred to4. The angle betweenas the rise over the run.a. Pitchb. Slopec. Valleyd. Truss5.A roof with four sloping sides.a. Shedb. Hipd.6.The part of a roof that extendsc. Gableover the wall.c. FasciaMansardd. Guttera. Overhang b. Eave7. A surface finish material used to cover another surface.a. Flashing b. Fasciac. Overhang d. Dormer8. A flat roof slanting in one direction.a. Gableb. Hipc. Dormer d. Shed9. A diagonal rafter that extends from the plate to the ridge to forma hip roof Type.c. Trussd. Flashing10.a. Purlins b. Hip RaftersThe vertical height of a roof.a. Riseb. Rund. Eavec. Ridged. Ridge

Note- Hi! Thank you for the question, As per the honor code, we are allowed to answer three…

_1. A horizontal structural member which hold the rafters together. a. Rafter b. Purlins 2. A prefabricated triangular c. Rise d. Run shaped unit supporting the roof loads over long spans. a. Truss b. Shingles c. Rise d. Ridge 3. The top edge of the roof where rafters meet a. Ridge b. Rafter c. Overhang d. Purlins 4. The angle between the top plate and the ridge board referred to as the rise over the run. a. Pitch b. Slope c. Valley d. Truss 5. A roof with four sloping sides. b. Hip a. Shed c. Gable d. 6. Mansard The part of a roof that extends over the wall. a. Overhang b. Eave c. Fascia d. Gutter 7. A surface finish material used to cover another surface. c. Overhang d. Dormer a. Flashing b. Fascia 8. A flat roof slanting in one direction. a. Gable b. Hip c. Dormer d. Shed 9. A diagonal rafter that extends from the plate to the ridge to form a hip roof Type. c. Truss d. Flashing a. Purlins b. Hip Rafters 10. The vertical height of a roof. a. Rise b. Run c. Ridge d. Eave

_1. A horizontal structural member which hold the rafters together. a. Rafter b. Purlins 2. A prefabricated triangular c. Rise d. Run shaped unit supporting the roof loads over long spans. a. Truss b. Shingles c. Rise d. Ridge 3. The top edge of the roof where rafters meet a. Ridge b. Rafter c. Overhang d. Purlins 4. The angle between the top plate and the ridge board referred to as the rise over the run. a. Pitch b. Slope c. Valley d. Truss 5. A roof with four sloping sides. b. Hip a. Shed c. Gable d. 6. Mansard The part of a roof that extends over the wall. a. Overhang b. Eave c. Fascia d. Gutter 7. A surface finish material used to cover another surface. c. Overhang d. Dormer a. Flashing b. Fascia 8. A flat roof slanting in one direction. a. Gable b. Hip c. Dormer d. Shed 9. A diagonal rafter that extends from the plate to the ridge to form a hip roof Type. c. Truss d. Flashing a. Purlins b. Hip Rafters 10. The vertical height of a roof. a. Rise b. Run c. Ridge d. Eave

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

F 3. Which of the following heavy timber frames must be buttressed or tied at the base to resist horizontal thrusts? a. Continuous girder b. Arch c. Truss d. Rigid frame or portal frame e. Dome
The floor system used in a school classroom consists of a 4-in. reinforced stone concrete slab. Sketch the loading that acts along the joist BF and side girder ABCDE. Set a = 10 ft, b = 30 ft. Hint: See Tables 1.2 and 1.4.
The post is fixed to the ground and a rectangular pressure of 7 lb/ ft2 acts perpendicular to the face of the signboard. What resultant internal loadings act on the cross-section through point B of the signpost?
Draw FBD of the beam
Give a short description of the space truss and of the suspension bridge
Given the faming plan a) Number all of the members properly in terms of joist, beam and girders. (note: there are no joists) b) Given DL = 60 psf and LL = 80 psf, draw the loading diagram (including determining the reactions) for all members within the shaded area
Draw SFD and BMD for a cantilever carrying UDL for a part of its length from the free end.
For the truss given below, what is the restraint that can not be remove to arrive with a primary structure?
The vertical bar is cantilevered to the floor asshown. Determine the moment of the loadsat B. Note: The trapezoidal load represents the soilpressure that is acting on the wall. This is also thetype of load acting on retaining walls.The moment at the base is required to determinethe size of the wall with steel reinforcements inrelation to the subject Reinforced ConcreteDesign)
P (kN)= 7 allow=45 Pin C=double shear Pin D=single shear
what additional load may be placed at the center of the span...
PROBLEM: Light grade steel channel was used as purlin of the truss. The top chord of the truss is inclined 1V:3H and the distance between the trusses is 5m. The purlin weighs 100n/m and spaced at 1m apart. The roof carries superimposed dead load of 1000 Pa (including its weight) and the ceiling carries a load of 1200 Pa. Roof live load is assumed to be 1500 Pa. The roof is part of the building located at a place where the design wind speed is 240 kph. Assume the unit weight of air to be 12 N/m3. The windward coefficient is 0.20 and the leeward coefficient is 0.70. For this problem, assume that the allowable bending stress of beam is 60% and 75% of its yield strength in the strong and weak axis respectively. Assume all loads passes through the centroid of the section. Properties of C 250x85 ; Sx= 122 x103 mm3 ; Sy= 49 x103 mm3; Fy=300 MPa; Fbx (Allow. Bending Stress)=0.6Fy;Fby (Allow. Bending Stress)=0.75Fy What is the ratio of the actual to allowable bending stress for load…