P (kN)= 7 allow=45 Pin C=double shear Pin D=single shear Q2. The frame is subjected to the load of P which acts on member ABD at D. Determine therequired diameter of the pins at Dand Cif the allowable shear stress for the material is tallow.Pin Cis subjected to single/double shear, whereas pin D is subjected to single/double shear.-1.5 m-1.5 m1.5 m

Given P (kN)= 7 Allowable shear stress=45Mpa Pin C=double shear Pin D=single shear

Answered: P (kN)= 7 allow=45 Pin…

Engineering

Civil Engineering

P (kN)= 7 allow=45 Pin C=double shear Pin D=single shear

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Q2: For the beam and loading shown, A- Draw the shear force and bending-moment diagrams. B-…

A: Whenever in the beam forces or load acting, due to that support shows the reactions to those forces…

Q: 03. Determine the forces in the members marked by "x" in the truss loaded as shown below. Use method…

A: ∑FY=0RA+RB=60+60+75+75+75+75=345Kn --1∑MA=060×4+60×8+75×12+75×20+75×24=RB×16 (Taking clockwise…

Q: It is obtained by fixing 4 wooden planks to each other with nails. given as a cross section. 2…

Q: A simply.supported beam 4 m long has a cross section shown. Determine the maximum uniformly…

Q: Prob. 5 (. | The figure shows a drill-rig pipe that is being picked up by a crane at point C. The…

Q: 180.0 40.601 7. One grid line = 1 foot. 2. Draw the arrows and label the reaction forces. Label the…

Q: The lap joint is connected by nine 20-mm diameter rivets. Assuming that the axial load P = "X" kN is…

A: A small piece of round steel forged in place to connect two or more than two steel members together…

Q: 25 mm 200 mm V 100 mm 25 mm 25 mm 25 mm 200 mm 25 mm

Q: Asteel shaft with a diameter 50 mmand length 1.25 mtransmits 60 kW from an electric motor to a…

Q: 6. Referring to Figure 6, compute the maximum force P that can be applied by the machine operator,…

Q: • Part A Suppose that P = 12 kN and P = 17 kN. (Figure 1) Determine the force in member CF of the…

A: Away from the joint : tension (+ve) Towards the joint : compression (-ve)

Q: Question 4 For the figure shown below, compute the shear force in section 1. Neglect the weights of…

A: To find shear force at point 1

Q: What is the Shear Load on segment A-B? * O - 27 kips -25 kips -21 kips O -19 kips What is the Shear…

A: Given a beam with symmetric loading conditions Required: To find shear load on segment A-B…

Q: 1. From the riveted bracket shown, find the maximum shearing stress and determine the thickness of…

A: Introduction- A rivet, head pins, or bolts is a permanent attachment in metalwork that has been used…

Q: n pin has a diameter of 25 mm and is subjected to double shear. 20°. B d.2 m 30°

A: D=25mm To find average shear stress in pin A and B

Q: G3//Draw shear and bending moment diagram as shown in figure. by graphical method. 162 kN-m 50 kN 10…

Q: A rectangular beam has a dimension of 210 mm x 260 mm. The simply supported beam is 5-m long and…

A: The values given in the question are as follows: Width of beam(b)=210 mm Depth of beam(d)=260 mm…

Q: A T- section is the cross section of a loaded beam as shown. Given: U1= 20 kN/m; M1 = 100 kN-m; P1 =…

Q: Q2. Knowing that each of the shafts AB, BC, and CD consists of a solid circular rod, determine: the…

A: To find Magnitude of maximum shearing stress in the shaft

Q: Q. 4) Determine the tension developed in each cord required for equilibrium of the (196.2 N) weight.…

A: Solution Given Data Weight = 196.2 N

Q: 6. From the given section of a wide flange shown below, what is the maximum horizontal shear stress,…

Q: 3) A simply supported beam constructed by four woods nailed together as shown in the figure. If each…

Q: . Determine the location of the shear center for the following section. b. Determine the shear…

A: Data Given: h1= 25mm h = 100mm b = 50mm Thickness = 4mm V = 20 kN Asked: Determine the location of…

Q: 5 A simply supported beam carrying floor joist shown in Figure 7.9 is made rectangular wood having a…

A: Given:- dimension=50mm x 100mm To find:- maximum shearing stress

Q: 4.4) The design shear strength D,V, is A) 81.1 kips B) 482 kips C) 529 kips D) 567 kips

Q: b) The 6 kN load P is supported by two wooden members of 75 x 125 mm uniform rectangular cross…

Q: Q2: For the beam and loading shown, A- Draw the shear force and bending-moment diagrams. B-…

Q: 1. Using Method of Joints, Determine the Internal Force for each member as shown in the figure. 2.…

A: in above question is asked for calcuating memeber forces with method of joints and section. first…

Q: Situtation 7. The concrete pier is subjected to soil pressure that causes the line loads shown.…

A: Given Data: Width of the concrete pier is B=2.5 m. Height of the concrete pier is H=4 m.

Q: Find the shearing stress (in MPa) experienced by a rivet of radius r=16 mm if a shear force F =362…

Q: 12 KN Q1 find stress Rod Rod D TCD TAB АВ CD beam 10 m A uniform beam supported by two beam have…

Q: A 200 mm -240 mm D 77 30 kN

A: Free body diagram of the given problem:

Q: (a) Draw the shear and bending-moment diagrams for the beam and the given loading. (b) Determine the…

A: Note: As you have not given the cros-section (size) of the beam so, without these dimensions we are…

Q: 1. Using Method of Joints, Determine the Internal Force for each member as shown in the figure. 2.…

A: Using Method of Joints, Determine the Internal Force for each member as shown in the figure. 2.…

Q: Determine all member forces. Using the Method of Joints. 30KN 30KN 15KN /1 2 (2 3. 4 3. 600 008

Q: 4.101 The principal stresses at a point in a bar are 160 N/mm² (tensile) and 80 N/mm² (compr.). The…

A: Given data: The principle stresses at a point in a bar are, σx=160 Nmm2 tensile σy=-80 Nmm2 compr.

Q: he member of the structure weights 200 lb/ft. Determine the smallest diameter pin in inches that can…

A: For member AB:

Q: 1What is the value of shear at B? 2At what distance from A is zero shear located? 3What is the…

Q: The rectangular plate is subjected to the deformation shown by the dashed line. Assume a = 575 mm,…

A: Determine the shear strains γxy and γx’y’ at point A.

Q: Q. No. 14: A short rectangular post supports compressive loads of P = 34 kN and Q = 18 kN as shown…

A: This question is related to the Combined Stresses from Strength of Material. In this question we…

Q: Problem #2 6 m Y kN/m A B The support at A can be assumed to be a roller. Point C is an internal…

Q: What is the value of R1 in kN? What is the value of R2 in kN? Locate the point of zero

Q: force in member CD using method of section * 10 kN 30° Aç 60 60° 60° 30 60 DE 2 m 2 m 2 m RA 6 kN RE…

A: first finding any the reaction at E by applying moment equation .

Q: 200 40 100 30

Q: What is the maximum value of shear at A?

A: Shear force us defined as rate of change of Bending moment along the length in a beam. Since, A is a…

Q: 1) Regd: Determine Maximum Shearing Stresses for the 3 segments and eat C 2) Re (2)Solid…

Q: What is the value of R1 in kN? What is the value of R2 in kN? Locate the point of zero shear…

A: THIS QUESTION IS VERY LENGTHY SO THIS QUESTION IS VERY LENGTHY SO I CAN ONLY ANSWER FIRST 3 SUBPARTS…

Q: Q5. A square box beam is made of two (20 x 80 mm) planks and two (20 x 120 mm) planks nailed…

A: Moment of the inertia od the beam I=MOI for compete beam-for hollow…

Q: Q. For the figures shown; 1. Draw S.F. & B.M. diagrams 2. Determine the maximum bending and shearing…

Q: Holes with diameter of 2.5 cm are punched on a steel plate whose ultimate shearing is 4245 kg/cm2.…

Concept explainers

Unit Conversion

Standard units are also called SI units. SI units are used for measuring a physical quantity satisfying certain conditions. There are two types of units: fundamental units and derived units. Fundamental units are physical quantities that are independent, that is, they do not depend on other quantities like mass, length, or time. There are plenty of quantities in our lives which need to be measured and compared. Measuring is the comparison of a particular physical quantity with its reference value. A unit is a measure of a fixed physical quantity. A physical quantity is the product of a unit and the numerical value we need to compare with.

Question

P (kN)= 7 allow=45 Pin C=double shear Pin D=single shear

Q2. The frame is subjected to the load of P which acts on member ABD at D. Determine the
required diameter of the pins at Dand Cif the allowable shear stress for the material is tallow.
Pin Cis subjected to single/double shear, whereas pin D is subjected to single/double shear.
-1.5 m-
1.5 m
1.5 m

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Statics Review. Make sure to draw FBD(s). Given the beam with loading as shown below: A 2 kN/m ILITI PE 5m B f 5m Find: (a) The reactions at A and D (b) The internal shear force at C (c) The internal moment at C 20kN E 5m с + 5m D UMI
The Channel section is used as a purlin placed on top of trusses with spacing of 4.9 m and slope 1V to 4H. The purling are supporting a total uniform load of 16 kN/m. Properties of Channel:Sx = 119 x 10^3 mm^3Sy = 87 × 10^3 mm^3 Questions:Compute the maximum bending stress if supported by sagrods at midpoint.
The frame is composed of members connected byfrictionless pins. Draw free-body diagrams of each mem-ber and determine the forces applied by the pins to themembers.
The 5 ft aluminum strut is fixed between the two walls at A and B. If it has a 2 in by 2 in square cross section, and it is subjected to the torque of 80 lb-ftat C located 2 ft from A. Determine the reactions at the fixed supports. Also, what is the angle of twist at C? Gal = 3.8(10)^3 ksi
In the cantilever shown, taking M1 = 16 kN-m, M2 = 11 kN-m, P1 = 3 kN, P2 = 7 kN.d) Determine the shear at X2 e) Determine the moment at X2
Calculate for the following member forces of the frame shown below using Portal Method. a. Shear at column FE, VFE in kN b. Shear at column ED, VED in kN c. Shear at beam FC, VFC in kN d. Moment at A, MA in kN-m e. Moment at girder KH, MKH in kN-m
A 5.0m simple beam supports the given floor loads Wu and a concentrated load Pu due to the wall transverse to the given beam. Answer the following questions given the sections of the beam. Calculate the depth of the neutral axis of the section in PART B in mm.0 Calculate the stress in the steel of the section in PART B in MPa.0 Calculate the ultimate moment capacity of the section in PART B in kN.m.0
Determine the shear at A for the column shown.
The top of the folding workbench has a mass of 50 kg with mass center at G. FH is a flexible cord or cable. Calculate the following: 1. Reaction at C 2. Vertical Reaction at D 3. ×-components of the force supported by the pin at E
The beam is supported by a pin connection at A and a roller at B. Beam AB supports a uniformly distributed load of 7.5 kN/m over the first 4 meters (x=0 to x=4) and supports a distributed load that decreases from w2=4.5kN/m to w3=0kN/m. Over all beam length (x) is 10 meters. Neglecting the self-weight of member AB, find" The reaction forces at A and B. The internal shear and moment at mid-span (x=5m) The equations for internal shear, V(x), and internal moment M(x), as a function of location (x) in the region for x between 0 and 4m of the beam.
10m beam is loaded with point load P1 = 100N at 2m from the fixed end support. A distributed load (W1) was also imposed with a magnitude of 100 N/m as shown. The beam is supported by a pin and a roller at locations specified in the free body diagram. what are the reactions in A and B at what distance will the shear be equal to ZERO between A and B what the computed maximum positive bending moment? Note: counterclockwise moment on the righthand side of the beam element be positive
The frame carrying a 384-kg load is supported by roller at D and smooth pin at A. Assuming double shear in all pin connections, calculate the pin reaction at E and shearing stress developed in the pins at B and C. Use a pin diameter of 16 mm in all connections.