A 0.2 m wide (out of plane) gate in a sea wall is hinged at A and bolted at B. Given the density of sea water is 1,025 kg/m3 and the depth of water hA = 4.2 m, determine the magnitude of the reactions at A and B that act normal to the gate. 1.0 m A B RA= (magnitude only; tolerance 5 N) RB = (magnitude only; tolerance 5 N) 数字单位单位 * * 0.6 m

A 0.2 m wide (out of plane) gate in a sea wall is hinged at A and bolted at B. Given the density of sea water is 1,025 kg/m3 and the depth of water hA = 4.2 m, determine the magnitude of the reactions at A and B that act normal to the gate. 1.0 m A B RA= (magnitude only; tolerance 5 N) RB = (magnitude only; tolerance 5 N) 数字单位单位 * * 0.6 m

Name: A 0.2 m wide (out of plane) gate in a sea wall is hinged at A and bol
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: A 0.2 m wide (out of plane) gate in a sea wall is hinged at A and bolted at B. Given the density of sea water is 1,025 kg/m³ and the depth of water hA = 4.2 m,determine the magnitude of the reactions at A and B that act normal to the gate.1.0 mABRA=

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter8: Centroids And Distributed Loads

Section: Chapter Questions

Problem 8.121P: One side of the container has a 03-m square door that is hinged at its top edge. If the container is...

See similar textbooks

Similar questions

The 12-ft wide quarter-circular gate AB is hinged at A. Determine the contact force between the gate and the smooth surface at B due to water pressure acting on the gate. Use =62.4lb/ft3 for water.
Figure (a) shows the cross-sectional dimensions for the structural steel section known as C1020 (channel with a nominal depth of 10 in., weighing 201b/ft). The American Institute of Steel Construction Structural Steel Handbook lists the following properties for the cross section: A=5.88in.2,Ix=78.9in.4, and Iy=2.81in.4. If two of these channels are welded together as shown in Fig. (b), find Ix and Iy for the resulting cross section.
One side of the container has a 03-m square door that is hinged at its top edge. If the container is filled with water, determine the smallest force F that must be applied to the bottom edge of the door to keep it closed.
vessel a, at elevation 2.438m, contains water under 103.4 kpa pressure. Vessel B at elevation 3.658 m, contains a liquid under 68.95 kpa pressure. if the deflection of the differential gage is 305 mm of mercury, with the lower level on the A side at elevation 0.305m, determine the specific gravity of the liquid in vessel B. Ans. 0.500
The 3 × 4-m side AB of a tank is hinged at its bottom A and is held in place by a thin rod BC. The maximum tensile force the rod can withstand without breaking is 200 kN, and the design specifications require the force in the rod not to exceed 20 percent of this value. If the tank is slowly filled with water, determine the maximum allowable depth of water d in the tank.
The 3 × 4-m side of an open tank is hinged at its bottom A and is held in place by a thin rod BC. The tank is to be filled with glycerine with a density of 1263 kg/m3 . Determine the force T in the rod and the reaction at the hinge after the tank is filled to a depth of 2.9 m.
A 27 m vertical column of fluid (density 1878 kg.m3) is located where g= 9.65 m/sec2. Find the pressure at the base of the column.Ans. 489.313 kPa Please give me the solution.
The blade of the bulldozer shown below is rigidly attached to a linkage consisting of the arm AB, which is controlled by the hydraulic cylinder BC. There is an identical linkage on the other side of the bulldozer. Applied loads shown are for both linkages and F = 581 kN. Determine the pressure in hydraulic cylinder BC in Pa if the cylinder has a diameter of 80 mm.
The rectangular panel, which is 4 m wide, 3 m high block the end of a 3 m deep water channel. The is suspended around a horizontal axis along its upper edge through point B and is prevented from opening by a fixed edge at point C. Determine the force which is exterted on the panel by the ridge as shown in fig.(2).
The water-gate articulated in point B and inclined at an alfa angle to the horizontal retains an H level of water. The gate is blocked by a cable which is anchored in the lower part of the dam. It is required to determine the force necessary to open the gate. The width of the water gate is 1 m.
Determine the smallest thickness (b) of the water gravity dam that will prevent it from tipping over due to the load from the water reservoir. The density of the concrete is 2.4 Mg/^3. The width of the dam is 1-m.
Show the derivation of the girth and longitudinalstresses of the thin-walled cylindrical container shownbelow. Say p is the internal pressure, d is the insidediameter of the container, and t is wall thickness.