• Part A The 23 ky slander red is allachod to a spring, which hs an unatretchec length ot 2 m. (Figure 1) If the rod is released from est vohen = 31, delramine Ihe angular vnlocily of the rod the inslant the spring becnmes unstreicherd, mneunod clockeise. Express your answer using three significant figures. Enter positive value if the angular vclocity is clackwise and negative value if the angular velocity is counterciockwise. It vec w= 3.32 rad/s Submit Previous AnawsE ResuestAnaer X Incorrect; Try Again; 5 attempts remaining

• Part A The 23 ky slander red is allachod to a spring, which hs an unatretchec length ot 2 m. (Figure 1) If the rod is released from est vohen = 31, delramine Ihe angular vnlocily of the rod the inslant the spring becnmes unstreicherd, mneunod clockeise. Express your answer using three significant figures. Enter positive value if the angular vclocity is clackwise and negative value if the angular velocity is counterciockwise. It vec w= 3.32 rad/s Submit Previous AnawsE ResuestAnaer X Incorrect; Try Again; 5 attempts remaining

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter7: Dry Friction

Section: Chapter Questions

Problem 7.61P

See similar textbooks

Similar questions

The turning moment diagram for a multi cylinder engine has been drawn toa scale of 1 mm = 4500 N -m vertically and 1 mm = 2. 4 ͦ horizontally. Theintercepted areas between output torque curve and mean resistance lineabove and below the mean taken in order from one end are 342, 23, 245,303, 115, 232, 227, 164 ??2, when the engine is running at 150 rpm. Ifthe mass of the flywheel is 1000 kg and the total fluctuation of speed doesnot exceed 3% of the mean speed, find the minimum value of the radius ofgyration.
The engine of the helicopter is delivering 600 hp to the rotorshaft when the blade is rotating at 1200 rpm. Determine to thenearest 1/8 in the diameter of the shaft is the allowable shearstress is 10.5 ksi and the vibration limits the angle of twist ofthe shaft to 0.05 rad. The shaft is 2 ft long and made fromsteel.
= 1 ective diameter of 75 i clutch have an effe S i, e 10.34, The contact surfaces in a cone requing s - S ind the torque The semi-angle of the cone is 15°, The coefficient of. s Pee : produce slipping of the clutch if an axial force applied is 180 N. . . orn, This cluch is employed o connect an electric motor running “mf”r:f o /‘.’K'W:‘ tha Jopwleel which s iniially stationary: The lywheel ha a mass of o e sricres o 150 mm. Calculate the time required for the flywheel to attain full speed and als 8 lostin the slipping of the clutch,
Determine the diameter of a solid steel shaft that will transfer 30 MW at 1500 RPM with a 1 degree twist angle for every 20 diameters of length. G=80GN/m2. Give me the solution of this please. Ans. D = 3.03 m
Determine the displacement of point C. Use the method of virtual work. EI is constant. Solve Prob. 9–37 using Castigliano’s theorem.
1. If the power generated is 10 kW, determine the minimum allowable angular velocity of the shaft (rad/s) 2. Determine the power generated if the angular velocity of the shaft is 30 rad/s Note: Please include the Freee Body Diagram.
Şekildeki parçalar birbirine M8-4.6 halite 4 cıvata ile bağlanmıştır. sürtünme katsayıları μ = 0.15 μs = 0.2 alınacaktır. 10000 Newton yükün sürtünmeyle taşınması için cıvataların ne kadar tork sıkılması gerekir. (Kaymaya karşı% 50 güvenlik gereklidir.)
I have the same question in my book. But the Rod is 30 kilogram and 1.5M length from A to B and spring spec K=300N/m. What would be the angular velocity when θ=0° (rad/s) ? Thanks in advance!
in the epicyclic gear, annulus gear B has 120 teeth externally and 100 teeth internally. driver A has 20 teeth and the arms E is connected to the driven shaft. The Sun gear D has 60 teeth. If A revolves at 100 r.p.m clockwise and D revolves at 27 r.p.m clockwise. If gear D is fixed and A transmits a torque of 10 N.m at 100 r.p.m clockwise
(Q.1) A compound epicyclic gear is shown in Fig. for Q.1. The shaft P is drivenat 3000 rev/min while the annulus A2 is driven at 1000 rev/min in theopposite direction. The numbers of teeth in the gears are S1, 16; S2,24; A1, 60; A2, 90. Determine the speed and direction of rotation ofshaft Q. (Q.2) A compound epicyclic gear is shown in Fig. for Q.2. C and D form acompound wheel which rotates freely on shaft G. The planet wheels B andE rotate on pins fixed in arms attached to shaft G. C and F have internalteeth: the others have external teeth with the following numbers: A, 40;B, 30; D, 50; E, 20. If A rotates at 500 rev/min and wheel F is fixed,find the speed of shaft G.
Steel bar in shape, AAB 600 mm and ABc = DACD3D 1200 mm2 are made of two stages. Determine the displacement at end A in (mm).
Two spur wheels with involute teeth gear together externally. The pitch circle diameters are 120 mm and 300 mm and the smaller wheel has 19 teeth. The pressure angle is 20o and the addendum is 0,3 of the circular pitch. Determine 1.1 The length of the arc of approach if the smaller wheel is the driver, and 1.2 The maximum velocity of sliding between the teeth when the driver rotates at 200 r/min