A 1-hour UH (1 unit=1 cm) can be represented by an isosceles triangle with peak at 4 hours and peak flow of 15 m³/s. The peak of the resulting streamflow from a 1-hour rainfall of depth 2 cm will be: 30 m3/s at 8 hours; 30 m3/s at 4 hours 15 m3/s at 4 hours; 15 m3/s at 1 hour;

A 1-hour UH (1 unit=1 cm) can be represented by an isosceles triangle with peak at 4 hours and peak flow of 15 m³/s. The peak of the resulting streamflow from a 1-hour rainfall of depth 2 cm will be: 30 m3/s at 8 hours; 30 m3/s at 4 hours 15 m3/s at 4 hours; 15 m3/s at 1 hour;

Fundamentals of Geotechnical Engineering (MindTap Course List)

5th Edition

ISBN:9781305635180

Author:Braja M. Das, Nagaratnam Sivakugan

Publisher:Braja M. Das, Nagaratnam Sivakugan

Chapter8: Stresses In A Soil Mass

Section: Chapter Questions

Problem 8.14P

See similar textbooks

Related questions

Q: 1. By any method, solve the axial bar forces of the truss shown, and identify whe ompression or…

Q: A series of previous CD tests conducted on a NC clay has established that the ultimate effective…

A: step 1-

Q: Q51. Prove that the force exerted by a jet of water on a fixed hemispherical curved vane when the…

Q: Draw the snear Tor ending ulagr answer the 400 lb/ft B

Q: A propped beam having a span of 20 m carries a triangular load with varies from 10 kN/m at the fixed…

A: Given : Support Reaction : For balance condition at point B;Maximum…

Q: 5-27 Consider two-dimensional, steady-state heat conduction in a region subject to the boundary…

A: Answer:-

Q: simply supported beam 120 mm wide, 180 mm deep and 6 m long carries a uniformly distributed load of…

Q: A wooden beam having a span of 4 m. is subjected to a uniform load of 10 kN/m. It has a triangular…

A: Calculate section modulus, flexural stress and maximum shearing stress on the beam

Q: Q24. Draw the plan, section and elevation of the given line diagram. W BED KITCHEN 2500x2500 D…

Q: IV. Analyze the frame. 6P (kN/m) loP (kN/m) 3m

Q: 1. Water flows steadily through the venturi section shown below. The volumetric flowrate Water flows…

Q: Determine the value of o for the rainfall hyetograph shown. Assume the depth of direct runoff is 2.5…

A: Answer:-

Q: a) Seepage beneath the dam (ft/min) b) Pressure head at points A and B b) Pore water pressure at…

A: (ft/min) seepage beneath the dam b) Points A and B of the pressure head d) Uplift force at the dam's…

Q: QUESTION I A flat roof spanning 4.25 n is to be designed using C24 timber joists at 600 mm centres…

Q: Wood blocking is to be used to support the keel of a 600 ton vessel in dry dock. What direction…

A: this question is asking about reason, type of wood used in dry dock for maintenance.

Q: Find the specific energy of flowing water through a rectangular channel of width 5 m when the…

A: The answer is found to be Specific energy =3.0226 m For explanation please refer the attached…

Q: The two bars are used to support load P. When unloaded, joint B has coordinates (0, 0). After load P…

Q: The observed annual runoff from a basin of area 500 km² is 150 Mm3 and the corresponding annual…

Q: Q17. The residential building with the dimensions is given in figure. Draw the plan and elevation.…

Q: A steel section having a cross section of 20 mm x 30 mm is subjected to an axial force of 240 kN.…

Q: A cantilever beam AB, loaded by a uniform load (see figure), is applied on a channel section. If the…

Q: In the quadrantal bearing system, a whole circle bearing of 293° 30' can * be expressed as W23°30'N…

Q: III. By any method, solve the axial bar forces of the truss shown, and identify whether it's…

Q: Q27. A rectangular channel with a bottom width of 4 m and a bottom slope of 0.0008 has a discharge…

Q: Water flows steadily through the venturi section shown below. The volumetric flowrate Water flows at…

A: Given Data -

Q: 10 ft/s

Q: 3. Consider the following data in the design of grit chamber : 1. Specific gravity of grit = 2.7 %3D…

Q: Calculate the hydraulic radius for a circular drain pipe running half full if its inside diameter is…

A: Note:- Hi! Thank you for the question As per the honor code, We’ll answer the first question since…

Q: Question 12 If the primary consolidation settlement of a clay layer is calculated to be 460 mm, what…

Q: 9. Find the specific energy of flowing water through a rectangular channel of width 5 m when the…

Q: 4. Anarea ļ 1o km20lem ie TO be survencd usi ng acrial photogd Average scale f photograph is…

Q: Explain and show conflict points of 1. Four-legged intersection 2. Five-legged intersection 3. Round…

A: “Since you have asked multiple question, we will solve the first question for you. If you want any…

Q: 1. The slope distance and altitude angle observed from point P to point Q were 2003.895 m and…

Q: Using the unit load method determine the vertical deflection at C. Ignore the contribution of the…

A: ###vertical deflection at c

Q: ries. The performance dat mps follow the parabolic vailable =HO =aV ^2. For p

A: Given:- Ho=av2 a=0.0438m/Lpm2 a=0.0347m/Lpm2 Ho=8.70m To find:- combined shutoff head

Q: Question 4 A simple beam AB supports a concentrated load P acting at distances a and b from the left…

Q: Draw the plan and elevation of the given line diagram. W W W BED 1 D KITCHEN AND DINING D D. С.В ++…

Q: Survey Survey Targe Reading Average Value after Average value after CLR zero station round face left…

A: Answer:-

Q: Compute the hydraulic radius for the channel shown in if the water depth is 2.50 m, in meters to the…

A: step 1-

Q: A 6m long beam is supported by hinge at point A(left end) and by roller at point C (3m right of A).…

Q: 4B.) The cylinder as shown below weighs F÷2 N. It is supported by a rod with a cable at point B.…

Q: Prepare a chart depicting significant developments in science and engineering by major civilizations…

Q: The variation of the total volume ( V) of a specimen of a fine soil with its water content ( w ) is…

Q: The three-bar truss ABC shown in the figure has a span L = 3 m and is constructed of steel pipes…

Q: EXAMPLE 3.5 A recently irrigated field plot has on Day I the total available soil mois- ture at its…

A: Given data, P = 0.2 K = 0.8 Evapotranspiration = 5.0 mm/day Day 1 soil moisture = 10 cm

Q: An inflow hydrograph to a 20 m wide x 85 m long x4 m (max height) detention basin has a constant…

Q: (a) Draw the dimensioned plan and elevation for the given line plan. Assume all suitable data. (b)…

Q: Determine the vertical displacement of end A and displacement of B relative to C in a composite A36…

Q: Question 6 A consolidation test was conducted on a clay sample and found that the clay has a…

Q: 4. Anarea fo km20 lem is TO be surveyed wsi ng acrial photogd Average scale f photograph is !:0,000…

Concept explainers

Field applications of hydraulic conductivity

Hydraulic conductivity is one of the hydraulic properties of soil defined as a measurement of the ability of a porous medium to permit water movement or fluid flow through it. It is denoted by the letter K. It is influenced by the density and viscosity of the fluid. It is also called permeability. Hydraulic conductivity is defined as the ratio of velocity to the hydraulic gradient. The different methods used to determine the hydraulic conductivity are laboratory methods (constant head permeability tests and falling head tests), in-situ field methods (pumping in and pumping out tests), small scale field tests (infiltration tests and slug tests), and indirect methods such as estimation from grain size, consolidation test data, and horizontal capillary test. The pedotransfer function (PTF) method is a specific empirical estimating approach employed in the soil sciences is also used to determine the hydraulic conductivity of the soil.

Question

100%

A 1-hour UH (1 unit=1 cm) can be represented by an
isosceles triangle with peak at 4 hours and peak
flow of 15 m³/s. The peak of the resulting
streamflow from a 1-hour rainfall of depth 2 cm will
be:
O 30 m3/s at 8 hours;
O 30 m3/s at 4 hours
15 m3/s at 4 hours;
15 m3/s at 1 hour;

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Field Applications of Hydraulic Conductivity

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Refer to Figure 6.14. Find the flow rate in m3 /s/m length (at right angles to the crosssection shown) through the permeable soil layer given H = 3 m, H1 = 2.5 m, h = 2.8 m, L = 25 m, a = 10°, and k = 0.04 cm/s.
Find the rate of flow in m^3/sec/m (at right angles to the cross-section shown in Figure 7.33) through the permeable soil layer. Given: H 4 m, H1 2 m, h 2.75 m, S 30 m, a 14°, and k 0.075 cm/sec.
A triangular SCS hydrograph (with excess rainfall Re=10mm and duration D=1hr) U(1,t) is illustrated below. The basin area is 24 km2.1.Estimate the values of Tc, Tp, Tr, Tb, and Qp.2.Determine U(2,t) by using the S-hydrograph method.
A total of 10 mm of rainfall fell on a lake with a surface area of T km^2 in June 1996. Relatedthe average flow rate of the stream entering the lake per month is 12 m^3 / s, while the average flow rate of the stream leaving the lake is7m^3/s dir. Monthly evaporation height measured in an evaporation pan near the lake during this month45mm and the pan coefficient in the relevant month is 0.75 according to what is the volume of water in the lake in this monthcalculate that it has changed up to?(T=159)
Determine the time of concentration for use in the Rational Method for a drainage basin having the hydraulic path described below:Overland Average Grass L = 80’ S = 2.5%Shallow Conc. L = 450’ S = 4.8%Gutter Flow L = 200’ S = 1.9%
The parameters of the Horton equation are fo = 7(cm/st), fc = 1 (cm/st) and the coefficient k = 4 (1/st¹). Accordingly, the total water leaking from an area of 2 ha to the ground in a day (24 hours) find its volume.
Refer to Problem 8.4. Using the flow net drawn, calculate the hydraulic uplift force at the base of the hydraulic structure per meter length (measured along the axis of the structure).8.24 For the hydraulic structure shown in Figure 8.24, draw a flow net for flow through the permeable layer and calculate the seepage loss in m3/day/m.
In a month of 30 days, the water level of a 1375-ha reservoir dropped by 0.75m in spite of an average inflow reservoir of 0.5 cu. Mm/day. During the month, the average seepage loss from the reservoir was 2.5 cm, total precipitation on the reservoir was 18.5 cm and the total evaporation was 9.5 cm. 1. Estimate the constant rate of withdrawal from the reservoir in m3/sec.
In an experiment on a trapezoidal notch the flow is collected in a 3.37 meter diameter vertical cylindrical tank. It is found that the depth of water increases by 1295 millimeters in 21.9 seconds when the head over the notch is 280 millimeters. The notch has a base of 1.57 meters and the sides are inclined at 58 degrees to the horizontal. Determine the coefficient of discharge of this notch
For the two-dimensional flow system shown below (units in meters):Compute the total flow rate under the Dam. X = 4, Y = 8. Note 1: Point A is located in the middle point of the equipotential lines. Point B is located in the middle point of the flow lines.Note 2: Assume e=0.8 (void ratio) and k=10^-3 cm/s (coeff. of permeability).Note 3: Datum is located at the bottom level of the water (right side of Dam).Note 4: Remember, the figure is drawn to scale. So, use the value of 2X+Y to estimate any dimension that you consider necessary.
Calculate the depth of water at the downstream of a hydraulic jump in a rectangular channel, where the flow rate is 3.1 m3/s, channel width is 1.5 m and upstream depth is 0.2 m. Choose one: 2 m 0.8 m 0.2 m 1.3 m
A stream conveying a flood peak of 40 m3/s (velocity 1.45 m/s and depth 0.9 m) is divided into 3.1 m long reaches for the solution of the unsteady equations. Calculate the largest value of Δt for which the solution will be stable?