The two bars are used to support load P. When unloaded, joint B has coordinates (0, 0). After load P is applied, joint B moves to the coordinate position (-0.56 in., -0.13 in.). Assume a = 14 ft, b = 28 ft, c = 10 ft, and d = 20 ft. Determine the normal strain in each bar. (2) A (1) B Answer: EAB = i με EBC = i με

The two bars are used to support load P. When unloaded, joint B has coordinates (0, 0). After load P is applied, joint B moves to the coordinate position (-0.56 in., -0.13 in.). Assume a = 14 ft, b = 28 ft, c = 10 ft, and d = 20 ft. Determine the normal strain in each bar. (2) A (1) B Answer: EAB = i με EBC = i με

Principles of Foundation Engineering (MindTap Course List)

8th Edition

ISBN:9781305081550

Author:Braja M. Das

Publisher:Braja M. Das

Chapter6: Vertical Stress Increase In Soil

Section: Chapter Questions

Problem 6.4P: Refer to Figure P6.4. A strip load of q = 900 lb/ft2 is applied over a width B = 36 ft. Determine...

See similar textbooks

Similar questions

Determine the shear stress (in Mpa) in the 20.75-mm-diameter pin at A that support the beam if P = 28.96 kN, a = 2.12 m, and b = 5.72 m. Round off the final answer to three decimal places.
a horizontal single force P of 150 lb magnitude is applied to the end D of lever ABD. 1. what is the normal and shear stresses at point H having sides parallel to the x and y axes? 2. determine the principal planes and pricipal stress at the point H
The frame (Figure 1) has dimensions H1 = 4 m , H2 = 3 m , L1 = 5 m , and L2 = 10 m and supports two lateral loads P1 = 10 kN and P2 = 12 kN . a) Use the portal method to determine the shear at J. VJ = ? b) What is the vertical reaction from the ground on the base of the column at AA? Let a positive reaction be pointing upward. Ay = ? c) What is the vertical reaction from the ground on the base of the column at B? Let a positive reaction be pointing upward. By = ?
12. The bell crank, which is in equilibrium under the forces P and F = 36 kN inclined at θ= 48o, is supported by a pin at D. Determine the shear stress (in MPa) in the pin if it is 21-mm-diameter. P is not equal to F. Round off to two decimal places.
1-10. A bar of variable cross section, held on the left, is subjected to three forces, P =4 kN, P, = -2 KN, and P, = 3 kN, as shown in the figure. On two separate diagrams, plot the axial force and the axial stress along the length of the bar. Let A1, = 200 mm, A2, = 100mm², and A3, = 150 mm".
given w = 8.2 kn/m and p = 15 kn for the beam below Calculate the vertical reaction at support A now. Provide your answer to 2 decimal places. Consider an upwards force as being positive, however only include a sign if the reaction is negative i.e. acts vertically down. Do not provide any units in your answer. Vertical reaction at A [kN] =
The simply–supported beam is loaded as shown. Use P = 8 kN and Q = 12 kN. Draw the shear and moment diagram. Plot the flexural stress distribution at point of maximum moment.
Determine support reaction .Take P=10 KN
Determine support reaction at B . Given P=100 Kn L=10 m
Determine the force in each member of the structure and establish whether the members are in tension or compression. Establish P1= 45 KN, P2= 30 KNSolve the problem considering the following: The force P1 will be the maximum point of a triangularly distributed load with a horizontal distribution of X meters.You must leave the solution in terms of X and show the particular solution when X is equal to 0m and 2m.
The elevation of the platform is controlled by two identical mechanisms, only one of which is shown. A load 1500 lb is applied to the mechanism shown. Knowing that the pin at C can transmit only a horizontal force, determine the stress at member BC if the area of member BC is 25 in².
Member AB has a uniform rectangular cross section of 10 x 24 mm. For the loading Pshown,a) Find reactions at A and B.b) Determine the normal and shearing stresses at Point K and Point H. α (˚) =30 P (kN)=14