A 1.2-m length of a steel pipe 500 kN of 200-mm outer diameter and 12-mm wall thickness is used as a column to carry a 500-kN centric axial load. Knowing that E = 200 GPa and v = %3D 1.2 m 0.30, determine (a) the change in length of the pipe, (b) the change in its outer diameter, (c) the change in its wall thickness.

A 1.2-m length of a steel pipe 500 kN of 200-mm outer diameter and 12-mm wall thickness is used as a column to carry a 500-kN centric axial load. Knowing that E = 200 GPa and v = %3D 1.2 m 0.30, determine (a) the change in length of the pipe, (b) the change in its outer diameter, (c) the change in its wall thickness.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A rectangular gravity dam has a height 5 m. It retains 3 mdeep of water. Calculate the minimum width of the concrete damthat is necessary to prevent the dam from sliding. The specificgravity of the concrete is 2.4 and the coefficient of frictionbetween the base of the dam and the foundation is 0.50. Use factorof safety against sliding of 1.5. a. 3.214 m b. 2.345 mc. 1.125 m d. 1.254 m
Consider the simple pipe network below. Pipe AB and CF are both 500m long withdiameters of 0.8m and friction factors of 0.015. Branch 1 is 200m long, 0.5m in diameter with a frictionfactor of 0.02. Branch 2 is 300m long, 0.6m in diameter with a friction factor of 0.012. The designdischarge through pipe AB is 3m 3 /s. Determine the following: a) the equivalent pipe length, Leq, of asingle equivalent pipe with a diameter of 1m and friction factor of 0.02, that represents the entire pipenetwork from A to F, b) determine the total head loss from A to F. Ignore minor losses. (Hint: need touse method of equivalent pipes for both series and parallel)
The semicircular drainage pipe is filled with water. Determine the resultant horizontal and vertical force components that the water exerts on the side AB of the pipe per foot of pipe length; γw = 62.4 lb/ft3.
1. Determine the head loss in the "smooth" pipe in meters if its friction factor is 0.014. a.) 39.5136 b.) 12. 9517 c.) 99.9358 d.) 30. 4889 2. What gage pressure p1 in kPa, is needed to provide the given flow rate? a.) 1121kPa b.) 1328kPa c.) 1692kPa d.) 1725kPa
A Triangular gate having a horizontal base of 1.30 m and an altitude of 2 m is inclined 45o from the vertical with vertex pointing upward. The base of the gate is 2.70 m below the surface of oil (s = 0.80). What normal force must be applied at the vertex of the gate to open it? Show figure
Obtain the gage pressure at the center A of the pipe shown. Neglect surface tension effects. For Liquid 1 specific gravity= 1.5, for liquid 2 specific gravity= 3.2, h1=15cm, h2= 30cm,h3=75cm
Water flows through a new cast iron pipe at a velocity of 1.8 m/s. The pipe is 480 m long and has a diameter of150mm. Determine the head loss due to friction using Manning’s formula with n = 0.012.
If the water surface elevation in reservoir B is 110 m, what must be the water surface elevation in reservoir A if a flow of 0.03 m3s is to occur in the cast-iron pipe? Use f = 0.021 for all pipes. Draw the HGL and the EGL, including changes in slope due to head loss. Neglect minor losses.
An open horizontal tank 2 m high, 2 m wide and 4m. long is full of water. a) How much water is spilled out when the tank is accelerated horizontally at 2.45 misec in a direction parallel with its longest side? b.) What is the porce acting on the side with the greatest depth? c.) Compute the required accelerating force.
What is the minimum width for the base of a dam 30m high if upward pressure beneath the dam is assumed uniformly from full hydrostatic head at the heel to zero at the toes? Use the resultant of the reacting force cut the base at the downstream edge of the middle third of the base at O and weight of the concrete is 2.5w.
The flowrate of the flow is 0.20 + a/10 m3 /s in a pipe placed on a horizontal plane. The pipe diameters are D1= 0.30 m and D2= 0.20. Please find the force acting to the pipe by the flow. The gauge pressure at (1) is p1 =200 + b*10 kN/m2 . (g=9,81 m/s2, g=10kN/m3 ) a= 4 b=3
Through the pipeline system in the figure calculate gauge and absulate presures at A and B