A 1.65m long rod with a circular cross-section is subjected to a tensile load of 50 kN. The rod is made from AISI 1040 hot-rolled steel. The allowable tensile stress is 165 MPa. The rod is permitted to elongate up to 7mm without causing any issues. The proportional limit for the steel is 180 MPa. (A) Compute the required area necessary to meet the stated requirements based on allowable stress. Express your answer in square millimeter units as an integer. (B) Compute the required area necessary to meet the stated requirements based on allowable elongation. Express your answer in square millimeter units as an integer.

A 1.65m long rod with a circular cross-section is subjected to a tensile load of 50 kN. The rod is made from AISI 1040 hot-rolled steel. The allowable tensile stress is 165 MPa. The rod is permitted to elongate up to 7mm without causing any issues. The proportional limit for the steel is 180 MPa. (A) Compute the required area necessary to meet the stated requirements based on allowable stress. Express your answer in square millimeter units as an integer. (B) Compute the required area necessary to meet the stated requirements based on allowable elongation. Express your answer in square millimeter units as an integer.

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter1: Introduction

Section: Chapter Questions

Problem 1.5.3P: A tensile test was performed on a metal specimen having a circular cross section with a diameter 0....

See similar textbooks

Similar questions

An aluminum pipe must not stretch more than 0.05in when it issubjected to a tensile load. Knowing that E=10.1x10^6psi and that the maximum allowable normal stress is 14ksi, determine (a) the maximum allowable length of the pipe, and (b) the required area of the pipe if the tensile load is 127.5kips.
Steel railroad rails 10 m long are laid with end-to-end clearance of 3 mm at atemperature of 15°C. (a) At what temperature will the rails just come in contact? (b)What stress would be induced in the rails at that temperature if there were no initialclearance? Use a = 11.7 x 10-6 PC and E = 200 GPa.
Determine the critical load on a column having a rectangular tube cross section 18 by 12 mm, a wall thickness 2 mm, and a length of 280 mm. The lower end of the column is securely welded while the upper end is pinned. Assuming that the yield strength Sy = 290 MPa and the modulus of elasticity E = 207 GPa
A 2500 lb horizontal bar is supported by three 3/16-inch diameter wires as shown. The wires are symmetrically spaced and 20 feet long. The two outer wires are steel and the middle wire is brass. Calculate: a) Stresses in the wires
A cantilever of circular solid cross section is fixed at one end and carries a concentrated load P at the free end. The diameter at the free end is 200mm and increases uniformly to 400mm at the fixed end over a length of 2 m. At what distance from the free end will the bending stress in the cantilever be maximum? Proceed to calculate the value of maximum bending stress if the concentrated load P = 30 kN. I need answer ASAP. Thank you!
A circular aluminum alloy [E = 70 GPa; α = 22.5 × 10–6/°C; ν = 0.33] pipe has an outside diameter of 225 mm, a wall thickness of 15 mm, and a length of 5.0 m. The pipe supports a compressive load of 670 kN. After the temperature of the pipe drops 48°C, determine: (a) the axial deformation of the pipe. (b) the change in diameter of the pipe.
A hollow circular column of steel (E = 30,000 ksi) is subjected to a compressive load P. The column has length L = 8.0 ft and outside diameter d = 8 in. The load P = 110 kips. (a) If the allowable compressive stress is 8.1 ksi, what is the required inside diameter (inches)? (b) If the allowable shortening of the column is 0.025 in., what is the required inside diameter (inches)?
A 1 meter long steel rod AB of 15-mm diameter is held snugly (without any initial stresses) between rigid walls by the arrangement shown in the figure. (STEEL ROD : E = 200 GPa , α= 12 x 10-6/°C , and yield strength σY = 250 MPa.) a) If the rod undergoes a temperature drop of 24°C, and the bolt at B is tightened causing the rod to elongate by 0.0566 mm, determine the bearing stress between the washer and the wall. b) Determine the amount of temperature drop that is allowed if the factor of safety against yieldingis 4.
If the gauge is made of a material having a yield stress equal to 200 Mpa, determine the minimum required diameter d. Using a Factor of safety (F.S=2)
A 4.8ft-long steel wire of 1/4in-diameter is subjected to a 750lb-Tensile load. Knowing that E=29x10^6psi, determine (a) the elongation of the wire, and (b) the corresponding normal stress.
Strength of materials - ENGR 3321 The answer should be: 17.68 kN; 11.8 MN/m2 compressive
Please solve asap!! The manhole cover of an ammonia storage tank is to be held by 25 stud bolts. If the pressure inside the storage tank will remain constant at 12.5 kg/cm2 and the manhole diameter is 508 mm, what should be the stress area of the carbon steel bolts?