Problem 2A 1.8 kg/s of steam expands in a turbine producing 550kW of power output. The steam enters at a velocity of18 m/s and exits at 70 m/s. The reduction of specificenthalpy is 400 kJ/kg. Determine that the heat flow persecond when the inlet of the turbine is located 900mm above the outlet.

Given data: W˙=550 kWm˙=1.8 kg/sv1=18 m/sv2=70 m/sh1-h2=400 kJ/kgz1=900 mmz2=0 Need to determine the…

Answered: A 1.8 kg/s of steam expands in a…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

3. Steam enters the turbine at the rate of 1.5 kg/s with enthalpy of 2300 kJ/kg and exhaust enthalpy of 1200 kJ/kg. Steam is extracted from the turbine at a rate of 0.87 kg/s for heating purposes with enthalpy of 2570 kJ/kg. What is the turbine work, in HP?
Question 3 Consider the turbocharger of an internal combustion engine. The exhaust gases enter the turbine at 450°C at a rate of 0.02 kg/s and leave at 400°C. Air enters the compressor at70°C and 95 kPa at a rate of 0.018 kg/s and leaves at 135 kPa. The mechanical efficiency between the turbine and the compressor is 95 percent (5 percent of turbine work is lost duringits transmission to the compressor). Using air properties for the exhaust gases, determine:(a).The turbine power output, compressor power input, air temperature at the compressor exit,(b).The air temperature at the compressor for the case of isentropic process and isentropic efficiency of the compressor.
A rotary air compressor is required to deliver 900 kg of air per hour. The enthalpy of the air at inlet and exit are 300 kJ/kg and 500 kJ/kg, respectively. The air velocity at the entrance and exit are 10 m/s and 15 m/s, respectively. The rate of heat loss from the compressor is 2500 W. Determine the power required to drive the compressor. Provide complete solution with diagram
In an adiabatic turbine, this steam flow is 50 kg / s. The power produced by the turbine is 29 MW.Steam enters the turbine with a pressure of 50 bar and a speed of 60 m / s. At the outlet, at a pressure of 0.06 barIt comes out as saturated water with a speed of 130 m / s. Accordingly, the heat lost by the turbine andFind the turbine inlet and outlet temperatures of steam
3. Steam enters the turbine at the rate of 1.5 kg/s with enthalpy of 2300 kJ/kg and exhaust enthalpy of 1200 kJ/kg. Steam is extracted from the turbine at a rate of 0.87 kg/s for heating purposes with enthalpy of 2570 kJ/kg. What is the turbine work, in HP? draw a diagram and show full solution
Steam enters a turbine stage with an internal energy of 3,072 kJ/kg at 69 m/s and leaves the same stage with an internal energy of 2,111 kJ/kg and a velocity of 113. Calculate the power (in kW) if there are 1.965 kg/s steam admitted at the turbine throttle?
A turbine, operating under steady-flow conditions, receives X1 kg of steam per hour (For X1 refer Table. 1). The steam enters the turbine at a velocity of 3000 m/min, an elevation of 5 m and a specific enthalpy of 2787 kJ/kg. It leaves the turbine at a velocity of 6000 m/min, an elevation of 1 m and a specific enthalpy of 2259 kJ/kg. Heat losses from the turbine to the surroundings amount to 16736 kJ/h. Determine the power output of the turbine.
Steam in an adiabatic turbine expands from a pressure of 6 MPa and a temperature of 300 °C to a pressure of 0.1 MPa, with a flow rate of 3 kg/s. If Steam leaves the turbine as saturated steam, what is the turbine's power output? last 2 min
A turbine is driven by a system that enters the turbine at the ff. conditions: 500 kg/h, 44 atm, 450 deg C, 60 m/s linear speed. The steam exits at a point five meters below the inlet stream of the turbine with the following conditions: atmospheric pressure, 360 m/s speed. 70,000 W of shaft work is delivered by the turbine while 104 kilocalories/h heat is lost. Why is expansion work 0 and why cannot the flow work be calculated?
A turbine is driven by a system that enters the turbine at the ff. conditions: 500 kg/h, 44 atm, 450 deg C, 60 m/s linear speed. The steam exits at a point five meters below the inlet stream of the turbine with the following conditions: atmospheric pressure, 360 m/s speed. 70,000 W of shaft work is delivered by the turbine while 104 kilocalories/h heat is lost. Here are the questions to be answered: 1. Why is the value of Wexp 0? (Explain) 2. Given the above values, can you calculate the Wflow? (Yes/No)
Air at 7°C enters a turbojet engine at a rate of 16 kg/s and at a velocity of 220 m/s (relative to the engine). Air is heated in the combustion chamber at a rate 15,000 kJ/s, and it leaves the engine at 427°C. Determine the thrust produced by this turbojet engine. (Hint: Choose the entire engine as your control volume.)
At a particular stage of a reaction turbine the mean blade speed is 140 m/sec and the steam is at a pressure of 20 bar with temperature of 250° C. Fixed and moving blades at this stage have inlet angles 30° and exit angles 20°. The stage efficiency is 80%. Determine (1) Specific entholpy drop across the stage in kJ/kg.

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS

A 1.8 kg/s of steam expands in a turbine producing 550 kW of power output. The steam enters at a velocity of 18 m/s and exits at 70 m/s. The reduction of specific enthalpy is 400 kJ/kg. Determine that the heat flow per second when the inlet of the turbine is located 900 mm above the outlet.