A 10-cm-diameter, 1.0-m-long solenoid is wound with 2000 turns of superconducting wire. When the magnet is turned on, the current increases from 0 to Imax in 2.5 s. At t = 1.0 s, the induced electric field midway between the axis and the windings is 7.5×10−3V/m. What is the solenoid's steady magnetic field strength?

A 10-cm-diameter, 1.0-m-long solenoid is wound with 2000 turns of superconducting wire. When the magnet is turned on, the current increases from 0 to Imax in 2.5 s. At t = 1.0 s, the induced electric field midway between the axis and the windings is 7.5×10−3V/m. What is the solenoid's steady magnetic field strength?

Physics for Scientists and Engineers: Foundations and Connections

1st Edition

ISBN:9781133939146

Author:Katz, Debora M.

Publisher:Katz, Debora M.

Chapter32: Faraday’s Law Of Induction

Section: Chapter Questions

Problem 21PQ: Figure P32.21 shows a circular conducting loop with a 5.00-cm radius and a total resistance of 1.30 ...

See similar textbooks

Similar questions

A thin conducting bar (60.0 cm long) aligned in the positive y direction is moving with velocity v=(1.25m/s)i in a region with a spatially uniform 0.400-T magnetic field directed at an angle of 36.0 above the xy plane. a. What is the magnitude of the emf induced along the length of the moving bar? b. Which end of the bar is positively charged?
A coil of area 0.100 m2 is rotating at 60.0 rev/s with the axis of rotation perpendicular to a 0.200-T magnetic field. (a) If the coil has 1 000 turns, what is the maximum emf generated in it? (b) What is the orientation of the coil with respect to the magnetic field when the maximum induced voltage occurs?
The square armature coil of an alternating current generator has 200 turns and is 20.0 cm on side. When it rotates at 3600 rpm, its peak output voltage is 120 V. (a) Wliat is the frequency' of the output voltage? (b) What is the strength of the magnetic field in which the coil is turning?
Copy Figure P30.6 and sketch the magnetic field lines that result from the bar magnets shown there.
The normal to tt plane of a single-turn conducting loop is directed at an angle to a spatially uniform magnetic field B. It has a fixed area and orientation relative to the magnetic fleck Show that the emf induced In the loop is given by i = (dB/dt)(Acos),where A is the area of the loop.
A uniform magnetic field B=5.44104iT passes through a closed surface with a slanted top as shown in Figure P31.59. a. Given the dimensions and orientation of the closed surface shown, what is the magnetic flux through the slanted top of the surface? b. What is the net magnetic flux through the entire closed surface?
A time-dependent uniform magnetic field of magnitude B(t) is confined in a cylindrical region of radius R. A conducting rod of length 2D is placed in the region, as shown below. Show that the emf between the ends of the rod is given by dBdtDR2D2 . ( Hint: To find the between the ends, we need to integrate the electric field from one end to the other. To find the electric field, use Faraday’s law as “Ampere’s law for E”.)
A square loop of side 2 cm is placed 1 cm from a long wire carrying a current that varies with time at a constant rate of 3 A/s as shown below. (a) Use Ampere’s law and find the magnetic field as a function of time from the current in the wire. (b) Determine the magnetic flux through the loop. (c) If the loop has a resistance of 3 how much induced current flows in the loop?
Figure P32.21 shows a circular conducting loop with a 5.00-cm radius and a total resistance of 1.30 placed within a uniform magnetic field pointing into the page. a. What is the rate at which the magnetic field is changing if a counterclockwise current I = 4.60 102 A is induced in the loop? b. Is the induced current caused by an increase or a decrease in the magnetic field with time?
If electric and magnetic field strengths vary sinusoidally in time at frequency 1.00 GHz, being zero at t=0, then E=E0sin2ft. (a) When are the field strengths next equal to zero? (b) 4Jhen do they reach their most negative value? (c) How much time is needed for them to complete one cycle?
The Hall effect is to be used to find the density of charge carriers in an unknown material. A Hall voltage 40 V for 3-A current is observed in a 3-T magnetic field far a rectangular sample with length 2 cm, width 1.5 cm, and height 0.4 cm, Determine the density of the charge carriers.
The world’s strongest magnet can produce a steady field of 45 T. If a circular wire loop of radius 10 cm were held at rest in this magnetic field, what current would be induced in the loop?