Answered: A 10 MW Diesel engine utilizes an…

A 10 MW Diesel engine utilizes an industrial fuel of 25 deg API at 27 deg C in one day operation. For a thermal efficiency of 45%, determine the capacity of fuel day tank

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter1: Basic Modes Of Heat Transfer

Section: Chapter Questions

Problem 1.75P: Referring to Problem 1.74, how many kilograms of ice can a 3-ton refrigeration unit produce in a...

See similar textbooks

Related questions

Q: The turning moment diagram of a quadruple expansion marine engine (multi cylinder engine) drawn to t...

Q: A ball is released from the bottom of an elevator which is traveling upward with a velocity of 6 ft/...

Q: 3) The aluminum and steel bars with the same dimensions are perfectly bonded in two different ways. ...

A: LONGITUDINAL STRAIN Longitudinal strain is a normal strain in the direction of load LATERAL STRAIN...

Q: e magnitude of the force required to hold the plate.

A: Given; Diameter, D=60 mm, water jet strikes a plate containing a hole of; Diameter, d=40 mm= 0....

Q: The work required to compress a gas reversibly according to PV1.30 = C is 67,790 J if there is no fl...

Q: QUESTION 5 LA local firm is planning its workforce and production levels over the next year. The fir...

A: Solution: Prepare the table as shown below: Month Number of Working days Demand Forecasting Units...

Q: Two stationary plates are separated by oil with a kinematic viscosity value of 7.380 cm2/s and speci...

Q: Determine if the following is true/false. Provide the necessary solution. The saturated temperatur...

A: Superheated steam is a very high-temperature vapour produced by heating saturated steam produced ...

Q: Entropy of the mixture?

A: Given; Volume, V=0.08m3Mass of liquid(m)=9 kgMixture of saturated water and saturated steam at =2000...

Q: image below, the force acting he box is F = (C · s²) Determine the work done by force F to the box w...

A: Given Force, F = C. S2 Distance, s = 1.7 Constant, C = 6 Find Work done, W

Q: A refrigerator uses refrigerant-134a as the working fluid and operates on the vapor-compression refr...

A: Given, Working Fluid as R-134a => Vapor Compression Refrigeration. P1 = 100 kPa = P4 P2 = 1400...

Q: A non-flow reversible constant volume process decreases the internal energy by 316.5 kJ for 2.268 kg...

Q: =150 le 120 F = 80 lb.

Q: For a steam turbine with the following data: Initial Temperature T0=36,7°C, Final temperature after ...

A: Given that, Initial temperature, T0=36.7 °C,Initial pressure, P0=1 bar,Final temperature of boiler, ...

Q: MIXING PROBLEM CONDITIONS: 1.) When start P.B (10.0) is pressed, Pump Motor No. 1 (Q0.0) is ON. 2.) ...

A: Here the diagram given is as follows For the motor and pump time on delay and the level sensor are g...

Q: (b) An empty steel cylinder is 2 ft. in external diameter and its wall is I in. thick. Find the rati...

Q: Q2. As shown on the right in image below, the force Facting on the box varies with displacement s, a...

Q: Determine the resultant of the load system shown. Locate where the resultant intersects grade with r...

Q: VE FUNCTIONS OF EACH COMPONENTS

A: we have to discuss functionality of different parts of tensile strength test.

Q: Moment diagrams. 14. (a) A timber beam of rectangular section is to support a load of 20KN/M uniform...

A: As we only solve upto one question, we will solve the first one. Please resubmit the other question ...

Q: A folding tray mechanism is attached to a wall as shown. Find the internal forces and bending moment...

A: Given data F=185N

Q: At the beginning of compression and ideal dual combustion cycle using air has a pressure of 15 Psia...

A: Given data: T1 = 75°C = 348 KP1 = 15 Psia = 103421.359 Pav1 = 13.2 ft3/lb = 0.824 m3/kg Constant vol...

Q: P3.50 The jet engine in Fig. P3.50 admits air at 20°C and 1 atm at (1), where A1 = 0.5 m2 and V1 = 2...

Q: 4. A 1.00 mole sample of a monatomic ideal gas, originally at a pressure of 1.00 atm, undergoes a th...

Q: What is the pressure of the system?

A: To determine the pressure of the system.

Q: ro0my32°c RHS 65.1. Pres Saturation paessuae of ssure in oom t03 MPa water 35°c is 465k Humidity raf...

A: Given:ϕ=0.65P=0.3 MPaPvs=4.65 KPa

Q: 1-What is hardness and what is the benefit of calculating it? 2- Classify the materials that have th...

Q: The rigid plate ACBD is supported by rollers at B, C, and D. (Assume that the +x-axis is to the righ...

Q: An isobaric process is a polytropic process. True or false

Q: F=13kN, angle α=44o. Cross sections of both rods are square with a side length of a. The rods are ma...

Q: 16. A dual cycle using air operates at 14.7 psia, 70°F and r = 7. The cylindér diameter of the engin...

Q: The shaft from a DC motor is connected to gear A which rotates at 45rps in clockwise direction. Gear...

Q: Question 1: For the following truss structure (with members AB, BC, AD, DE, BE, CF and FG all of 60 ...

Q: For the structure shown below, the shear stress in the pin at B is determined a MPa if it has a diam...

Q: A compressor performs 200 hp of shaft work to compress 0.2 kg/sec of steam from saturated vapor at 1...

Q: l = 1.95 mm. w= 1.89 mm. h= 5.82 m. Coordinates for Point A is A(2,2,2)m Coordinates for Po...

A: As per the guidelines, I can solve only first three subparts. For rest parts, repost in a separate p...

Q: A) Find the acceleration constraint for this system. It is a single equation relating a1y , a2y a...

Q: St find frmperature at the triple point? Vapow pressure of.liquid & Sofid ammong are respectiveley g...

A: It is required to determine triple point temperature of ammonia

Q: Write the expression, in Excel notation, that you would type into cell 86 to determine the displacem...

A: Springs, follow the Hooke's law. It states that the Force(F) needed to extend a spring through a def...

Q: Compute the a) air to fuel ratio by weight, b) atomic ratio of H/C, and c) % excess air or % theoret...

A: ACCORDING TO THE GIVEN DETAILS

Q: In the figure shown, the end A of a bar AB, is constrained to move along vertical path AD and the ba...

Q: Temp. At the triple point

A: Given; Vapour pressure of liquid and solid ammonia are respectiveleygiven by; ln P=14.15-3054/T ln P...

Q: Pressure in om+03 MPa Saturation pressure of water + 35°c is. 465KPa Humidity ratio of Phe air?

A: we have to calculate the humidity ratio of air

Q: gas in a piston-cylinder assembly undergoes a process for which the relationship between pressure an...

A: Given:PV2=CP1=9 barV1=2 m3P2=4 bar

Q: The belt drive in which pulleys rotate in the same direction is used to transfer power. The pulley d...

Q: This question requires the use of the extracts from the tables of thermodynamic properties supplied....

Q: Problem: A pump draws water through a 300-mm diameter cast iron pipe, 15 m long from a reservoir in ...

Q: Starting from rest, a particle moving in a straight line has an acceleration of a= (5t2 – 2t) m/s2, ...

A: For calculating velocity after 2sec and position after 8sec, we integrated the given equation for th...

Q: The stroke and cylinder diameter of a compression ignition engine are 250 mm and 150 mm respectively...

Q: he a torque T4 ot uired value of F; t friction, gravity

Question

A 10 MW Diesel engine utilizes an industrial fuel of 25 deg API at 27 deg C in one day operation. For a thermal efficiency of 45%, determine the capacity of fuel day tank.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Discuss and Illustrate the PV diagram for Carnot Cycle.
Based on a gas turbine with superheat and intercooling, determine: 1) The thermal efficiency (ƞterm), in %. Use the expression ƞterm= 1 –(qL/ qH)2) How does gas turbine intercooling influence thermal efficiency?3) How and why? It is said that the gas turbine cycle with intercooling, reheating and regeneration is close to the Ericsson cycle.
2. A waste heat recovery boiler produces 4.8MPa (dry saturated) steam from 103 deg C feedwater. The boiler receives energy from 6 kg/s of 945 deg C dry air. After passing through a waste heat boiler, the temperature of the air has been reduced to 343 deg C. How much steam in kg is produced per second? (Hint: Approximate Enthalpy of Water in kJ/kg = Cp(t); where t is in 0C) @4.8 MPa dry saturated: h = 2796 A. 1.8 C. 1.53 B. 2.98 D. 1.54
A diesel electric plant in one of the remote provinces in the South utilizes diesel fuel with a ˚API of 28 at 15.6˚C. The plant consumes 680 liters of diesel fuel at 26.6˚C in 24 hours while the power generated for the same period amounts to 1980 kW – hrs. Determine overall thermal efficiency of the plant.
Brayton cicle Based on a gas turbine with superheat and intercooling, determine: 1) The thermal efficiency (ƞterm), in %. Use the expression ƞterm= 1 –(qL/ qH)2) How does gas turbine intercooling influence thermal efficiency?3) How and why? It is said that the gas turbine cycle with intercooling, reheating and regeneration is close to the Ericsson cycle.
An aircraft with a turbojet engine flies at 260.8 m/s. The engine burns fuel with a heating value of 49.6 MJ/kg, and its propulsive efficiency is 0.43%. If the fuel-air mass fraction of the engine is 0.5% (i.e., for every kg of working fluid passing through the engine, 0.005 kg of fuel is burned), determine the velocity of the working fluid in the exhaust to the nearest m/s. As an initial step, you may find it helpful to express the propulsive work and heat in terms of the mass flow rate of working fluid.
Please explain as much as possible such as specific energy input and output If 19.5 MJ can be produced by burning 0.5 kg of a certain fuel, and if an engine has a fuel consumption of 240 kg/MW·h, what is the efficiency of the engine?
A 350-MW simple-cycle gas turbine power plant operates with a compressor pressure ratio of 16, TIT of 1450°C and compressor intake temperature of 10°C, and pressure of 1 bar. The fuel natural gas with an LHV of 50 MJ/kg is burned in a gas turbine combustor. The compressor and turbine isentropic efficiencies are 0.87 and 0.92, respectively. Calculate (a) the fuel consumption rate, (b) the turbine exit temperature, and (c) the plant thermal efficiency.
Q#3: a. With the help of schematic diagram explain the Steam power plant. b. How we can improve the overall efficiency of a steam power plant?
A 21 MW coal-fired power plant has an efficiency of 42%. Estimate the annual consumption of coal (in tons per year) burned in this plant. Assume a heating value of approximately 7.5 MJ/kg (megajoules per kilogram) for coal.
Draw the pV diagram for the Stirling engine with proper labels?
Steam enters the turbine of a power plant operating on the Rankine cycle (Fig. 2) at 873.15 Kand exhausts at 30 kPa. To show the effect of boiler pressure on the performance of the cycle,calculate the thermal efficiency of the cycle and the quality of the exhaust steam from theturbine for boiler pressures of 5000,7500, and 10 000 kPa. #Chemical Engineering #Chemical #Thermodynamics