"A 100 kW, 250 V machine-A is in parallel with a 300 kW, 250 V machine-B. The voltage regulation of both machines is 4 percent. Machine-A is carrying 200 Amp and machine- B is carrying 500 Amp. What will be the increment increase in load on machine-A and B respectively (in Amp) if an additional 400 Amp load is connected to the bus?" 100 & 300 300 & 800 400 & 1200 None is correct

"A 100 kW, 250 V machine-A is in parallel with a 300 kW, 250 V machine-B. The voltage regulation of both machines is 4 percent. Machine-A is carrying 200 Amp and machine- B is carrying 500 Amp. What will be the increment increase in load on machine-A and B respectively (in Amp) if an additional 400 Amp load is connected to the bus?" 100 & 300 300 & 800 400 & 1200 None is correct

Electrical Transformers and Rotating Machines

4th Edition

ISBN:9781305494817

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter3: Inductance In Alternating-current Circuits

Section: Chapter Questions

Problem 5RQ: Three inductors are connected in parallel. Inductor 1 has an inductance of 0.06 H; inductor 2 has an...

See similar textbooks

Similar questions

The collector leakage current in a transistor is 300 μA in CE arrangement. If now the transistor is connected in CB arrangement, what will be the leakage current? Assume β = 120. (2) For a certain transistor, IB = 20 μA; IC = 2 mA and β = 80. Calculate ICBO. (3) In a transistor, IB = 68 μA, IE = 30 mA and β = 440. Determine α rating of the transistor. Then determine the value of IC using both the α rating and β rating of the transistor.
Three inductors are connected in parallel. Inductor 1 has an inductance of 0.06 H; inductor 2 has an inductance of 0.05 H; and inductor 3 has an inductance of 0.1 H. What is the total inductance of this circuit?
A(n)_______varies the frequency of an electronically altered sine wave, which affects the speed of alternating current motors.
A piezoelectric actuator is made from a stack of 20 square piezoelectric pads, each 10mm squarewith a thickness of 2mm? Calculate the maximum displacement when 1kV is applied given that d33=100×10-12 C/N, er = 50 and Y = 50GPa.
A motor running 1800rpm transmits 10KW of power through a 25mm diameter shaft 1.2m long. What is the angle of twist in the shaft? G=8.3x10^10 Pa. A)1.14 degree B)1.59 degree C)1.34 degree D)1.04 degree
2 EXAMPLE OF FAILURE CAUSED BY RESONANCE
Q1 / A DC shunt generator delivers 187 A at 260 V. The armature resistance and shunt field resistance are 0.028 2 and 48 2 respectively. The sum of stray losses equal 950 W. Find the machine efficiency.
A. Incident sound waves in a dynamic pickup or microphone lead to the passage of AF current in the coil because- 1) The coil's motion within a magnetic field. 2) The motion within an electrostatic field.3) A DC voltage is applied to the coil. 4) Changes in the capacitive reactance across the coil. B. An intermittent (as opposed to continuous) motor is one in which the shaft revolves in- 1) An incremental motor. 2) A stepper motor. 3) A selsyn. 4) A fractional motor.
Given the following Resistances and Inductors in Series and Voltage Source: R1 = 1,664 ohms R2 = 1,999 ohms L1 = 2 Henry L2 = 2 Henry Vs = 3 Volts Frequency = 92 Hz What is the Total Impedance (Amplitude) in ohms?
Mechanical Engineering In a lamellae clutch, the number of inner lamellae zi= 5 pieces, the number of outer lamellas zd=6 pieces. If the inner radius of the lamella is ri=70mm, the radius of the outer lamella is rd=120mm, the surface safety pressure of the lamella material is pem =0.8 MPa, the friction coefficient is u=0.1, what is the maximum power that the clutch can carry at n=120 rpm?
A 3-phase, 50 Hz, 3000 V motor develops 600 H.P. (447·6 kW), the power factor being 0·75 lagging andthe efficiency 0·93. A bank of capacitors is connected in delta across the supply terminals and powerfactor raised to 0·95 lagging. Each of the capacitance units is built of five similar 600-V capacitors.Determine the capacitance of each capacitor.
Mechanism and Kinematic Terminology Give three example of a machine for: generating powert, transmitting energy, and utilizing mechanical energy in the performance of useful work.