Determine FOS using max. Distortion energy theory? A shaft is subjected to pure torsional moment.The maximum Shear stress developed in theshaft is 100 MPa. The yield and ultimatestrengths of the shaft material in tension are300MPA and 450MPA, respectively.

Given; A shaft is subjected to pure torsional moment.Maximum shear stress,σmax=100 MPaYield…

Answered: FOS using max. Distortion energy…

Engineering

Mechanical Engineering

FOS using max. Distortion energy theory?

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter3: Torsion

Section: Chapter Questions

Problem 3.7.8P: A tubular shaft being designed for use on a construction site must transmit 120 kW at 1,75 Hz, The...

See similar textbooks

Related questions

Q: Subject: Vibration Engineering Determine the degrees of freedom (c)

A: The given problem is based on vibration analysis.

Q: A motor manufacturer starts a batch of 374 motors . 20% of the motors have defects when p an be…

A: GivenTotal width=374 Defective motors=20100×374=74.80Rewarded motors=50100×74.80=37.4Total direct…

Q: From among the following select the truest statement. The Distortion Energy theory is a special case…

A: The given problem is based on theory of failure.

Q: Define the term torque diagram?

Q: Vibration isolation, transmissibility, Explanation magnification factor

A: Solution:

Q: Q16: What is the period of a wave of frequency 30 Hz?

A: As per our guidelines we are supposed to solve only one question if multiple questions are asked .…

Q: What is the coefficient of viscous damping force?

A: Viscous damping is based on the principle of conversion of the kinetic energy of the vibration into…

Q: In _vibrations, the amplitude of vibration reduces over every cycle of vibration. O forced O free…

A: In _________vibrations, the amplitude of vibration reduces over every cycle of vibration. O forced O…

Q: [e] = (° ) Cx Compatible deformation field Incompatible deformation field

A: It is also known as strain tensor field. A compatible deformation in a body is that unit tensor…

Q: advantages and disadvantages of vibration damping and vibration isolation

Q: QUESTION 1 Suppose the frequency of a system is measured to be 2rad/s and after the addition of…

A: Frequency of spring mass system is given as ω=km where ω, k, and m are angular frequency, spring…

Q: Why a small volume of sample limits the use of ring detachment method (Du Nouy Tensiometer)?

A: The Du Noüy ring method is used to measure the surface tension of a liquid and the interfacial…

Q: Resonance frequency of structural members can be detected with:

A: we will discuss vibration analysis of structural members

Q: 83

A: Here, there are 3 disks and all has diffrent angular perturbation. so, in the equation of motion…

Q: 1. A vibratory system where proportionality can be established between the motion and the force…

A: Solution: Note: Dear Student! As per our guidelines, we are only allowed to answer three sub-parts…

Q: Determine the degrees of freedom

Q: very valuable fx anand fy

Q: Nou Conformance t found wwle to paodu withim the po in Stiu r per

A: Given Data⇒ Product Cost

Q: What is Zero displacements?

A: Displacement is the smallest distance between the final state and the initial state of the body. It…

Q: What is good vibrations and what is bad vibration with example of each two vibration

A: Good vibrations and Bad vibration

Q: To produce a vibration, what three (3) properties of a body must a force overcome?

A: The answer of given problem is shown below

Q: the differential equation and find the natural frequency. (Mech. Vibration)

Q: What is the equation of compatibility?

A: In strength of materials we come across two types of beams-statically determinate and statically…

Q: Cp = Cv + R Prove?? %3D

A: Relation between two specific Heat

Q: What is the mechanical advantage of this system?

A: We have to first draw free body diagram of the block and the pulleys and then derive a relationship…

Q: What happens to the Marin temperature factor (kd) when the desired operating temperature of a…

A: What happens to the Marin temperature factor (kd) when the desired operating temperature of a…

Q: A- There are good and bad effects of mechanical vibrations. Give five examples of the bad effects of…

A: To explain: The effect of vibration. Concept used: Vibration: Mechanical vibration is defined as the…

Q: Metrology Discuss both figures and explain which one comply with Taylor principle and why?

A: Taylor's principle in metrology says that the GO gauge should check all the dimensions of the…

Q: Indicate whether the terms are like or unlike. - 322, 5z? ... The two terms 5z and - 3z are

A: The two terms 5z2 and -3z2 are like terms.

Q: Briefly explain the following terms. Mechanical Vibration.…

A: Hi and thanks for the question. Since you have asked questions with multiple sub parts, We will…

Q: Give detailed description of at least two methods of vibration measurement.

Q: What is the maximum distortion energy theory?

A: Maximum distortion energy theory: It states that the failure of the specimen occurs when the…

Q: What is the function of vibration absorber?

A: *Apparently, vibration absorber does absorb the vibration of the system it is installed--this is to…

Q: What is the coefficient of critical damping?

A: Coefficient of critically damping is defined as the value of damping coefficient at which the…

Q: Q4: what is the difference between Wn and Wd? *

A: In Mechanical Engineering the natural frequency is defined as the frequency at which a system…

Q: A compressor that has been in service for 20 years has finally broken down beyond repair, and now…

A: Solution: Given Data: Pold=180 hpPnew=400 hpCIold=144.5CInew=252.4n=0.32Mold=$1200

Q: a material is diamagnetic, what shall be the value of X ? Option 1: Negative Option 2: Positive…

Q: How magnification factor varies with damping ratio for a particular value of frequency ratio?

Q: What is damping factor?

A: Damping factor is a ratio used in the study of vibration of a system which has kinetic friction. It…

Q: ive vibration why their considered

A: To describe Nature of impulsive vibration why their considered as destructive.

Q: n rati

A: given: what is poisson ratio?

Q: How can we obtain the distortion energy per unit volume?

A: Consider P be the gradual load applied to the bar of length L and the uniform area A. Let dl be the…

Q: Write down the working principle of tuned vibration absorber.

A: Tuned vibration absorber:- Tuned vibration absorber can be effectively used to suppress forced…

Q: What is magnetic damping and how is it produced?

A: Magnetic damping Mechanical damping produced by the reaction of a magnetic field with eddy…

Q: What is natural frequency?

A: Natural frequency is the oscillation of mechanical or any system in the absence of any driving or…

Q: Name different types of vibration maximum have 10-7 names

A: There are mainly three types of vibrations: Free Vibration: When the vibrations are not influenced…

Q: had a natural frequency of 20 cycles/second. What is the approximate fundamental frequency of…

A: Applying Dunkerly's principle, 1⁄(ω12)+1⁄(ω22)+1⁄(ω32) = 1/100 + 1/400 = 1/80 Therefore ω1=80…

Concept explainers

Torsion

In mechanical engineering, torque, torsion, and twisting moment are three of the most important concepts which have different meanings. Torque is the consequence of a moment of a force that produces an angular acceleration in a body or induces rotational kinetic energy in a body. For instance, in an automobile, the power transmission shaft is a body that is always under rotation due to the external torque acting on it, this torque is created by the engine.

Question

Determine FOS using max. Distortion energy theory?

A shaft is subjected to pure torsional moment.
The maximum Shear stress developed in the
shaft is 100 MPa. The yield and ultimate
strengths of the shaft material in tension are
300MPA and 450MPA, respectively.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A circular aluminum tube subjected to pure torsion by torques T(sec figure) has an outer radius r2equal to 1.5 times the inner radius r1. (a) If the maximum shear strain in the tube is measured as 400 × 10-6 rad, what is the shear strain y1at the inner surface? (b) If the maximum a1lo-abk rate of twist is 0.125 °/m and the maximum shear strain is to be kept at 400 × 10-6 rad by adjusting the torque T, that is the minimum required outer radius ( r2)Min?
Two sections of steel drill pipe, joined by bolted flange plates at B, arc subjected to a concentrated torque 4000 kip-in. at x = 3 ft, and a uniformly distributed torque t0= 50 kip-ft/ft is applied on pipe BC. Let G = 11,800 ksi and assume that pipes AB and BC have the same inner diameter, d = 12 in. Pipe AB has a thickness tAB= 3/4 in., and pipe BC has a thickness tBC= 5/8 in. Find the reactive torques at A and C and the maximum shear stresses in each segment.
A propeller shaft for a small yacht is made of a solid steel bar 104 mm in diameter. The allowable stress in shear is 48 MPa, and the allowable rate of twist is 2.0° in 3.5 meters. (a) Assuming that the shear modulus of elasticity is G = 80 GPa, determine the maximum torque that can be applied to the shaft. (b) Repeat part (a) if the shaft is now hollow with an inner diameter of 5d18. Compare values to corresponding values from part (a).
A tubular shaft being designed for use on a construction site must transmit 120 kW at 1,75 Hz, The inside diameter of the shaft is to be one-half of the outside diameter. If the allowable shear stress in the shaft is 45 MPa, what is the minimum required outside diameter d?
The stepped shaft shown in the figure is required to transmit 600 kW of power at 400 rpm. The shaft has a full quarter-circular fillet, and the smaller diameter D1= 100 mm. If the allowable shear stress at the stress concentration is 100 MPa, at what diameter will this stress be reached? Is this diameter an upper or a lower limit on the value of D2?
A stepped shaft ABC consisting of two solid, circular segments is subjected to uniformly distributed torque t1acting aver segment 1 and concentrated torque t2applied at C, as shown in the figure. Segment 1 of the shaft has a diameter of d1= 57 mm and length of L1= 0.75 m; segment 2 has a diameter d2— 44 mm and length L2= 0.5 m. Torque intensity /,"= 3100 N . m/m and T2= 1100 N. m. (a) Find reaction torque TAat support A. (b) Find the internal torque T(x) at two locations: .x = L1/2 and at .x = L1+ L2/2. Show these internal torques on properly drawn free-body diagrams.
A stepped shaft ABC consisting of two solid, circular segments is subjected to torques T}and T2acting in opposite directions, as shown in the figure. The larger segment of the shaft has a diameter of dv- 2.25 in. and a length Lt= 30 in.; the smaller segment has a diameter d2— 1.75 in. and a length L, = 20 in. The torques are T, = 21,000 lb-in. and fz=10.000 lb-in. (a) Find reaction torque TAat support A. (b) Find the internal torque T(x) at two locations: x = L1/2 and x = L1+ L2/2. Show these internal torques on properly drawn free-body diagrams (FBDs).
A solid circular steel cylinder S is encased in a hollow circular aluminum tube A. The cylinder and tube are compressed between the rigid plates of a testing machine which applies forces P. Calculate the allowable value of the compressive force if the yield stresses of sleel and aluminum are srs = 50 Ksi and ??A= 60 ksi, respectively. Assume that As= 12 in2. AA= 6 in2. L = 20 in., Es= 29,000 tsi and EA=10,600 ksi
A solid copper bar of circular cross section has length L = 1.25 m and shear modulus of elasticity G = 45 GPa. The bar is designed to carry a 250 N · m torque acting at the ends. If the allowable shear stress is 30 M Pa and the allowable angle of twist between the ends is 2.5°, what is the minimum required diameter?
A stepped shaft ACB having solid circular cross sections with two different diameters is held against rotation at the ends (sec figure). If the allowable shear stress in the shaft is 6000 psi, what is the maximum torque (T0) that may be applied at section C? Find (T0)max if the maximum angle of twist is limited to 0.55º. Let G = 10,600 ksi.
A thin-walled aluminum tube of rectangular cross section (sec fig me) has a centerline dimensions b = 6.0 in. and b = 4.0 in. The wall thickness t is constant and equal to 0.25 in. Determine the shear stress in the tube due to a torque T = 15 kip-in. Determine the angle of twist (in degrees) if the length L of the tube is 50 in. and the shear modulus G is 4.0 x 106 psi.
A hollow steel shaft used in a construction auger has an outer diameter d2= 6.0 in. and inner diameter d1= 4.5 in. (see figure). The steel has a shear modulus of elasticity G = 11.0 × 106 psi. For an applied torque of 150 kip-in., determine the following quantities: shear stress at the outer surface of the shaft, shear stress at the inner surface, and rate of twist (degrees per unit of length). Also, draw a diagram showing how the shear stresses vary in magnitude along a radial line in the cross section.