A 10mm diameter and 20m long smooth tube is maintained at a constant surface temperature. Water enters the tube at 25 °C with mass flow rate of 0.01 kg/s. Properties of water at average mean temperature are: K= 0.65W/m.K, dynamic viscosity = 0.486X10^-3 Kg/m.s, Pr = 3.12 The flow at the end of the pipe is

A 10mm diameter and 20m long smooth tube is maintained at a constant surface temperature. Water enters the tube at 25 °C with mass flow rate of 0.01 kg/s. Properties of water at average mean temperature are: K= 0.65W/m.K, dynamic viscosity = 0.486X10^-3 Kg/m.s, Pr = 3.12 The flow at the end of the pipe is

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter6: Forced Convection Over Exterior Surfaces

Section: Chapter Questions

Problem 6.15P

See similar textbooks

Similar questions

6.3 Steam at 100 kPa and is flowing across a 5-cm- OD tube at a velocity of 6 m/s. Estimate the Nusselt number, the heat transfer coefficient, and the rate of heat transfer per meter length of pipe if the pipe is at .
Water at 70 °F is to be passed through a 1 micron-thick, porous PE membrane of 25% porosity with an average pore diameter of 0.3 micron and an average tortuosity of 1.3. The pressure on the downstream and upstream sides of the membrane are 125 and 500 kPa, respectively. Estimate the flow rate of water through the membrane.
Consider a flow with pressure and temperature of 1 atm and 288 K. A Pitot Tube is inserted into this flow and measures a pressure of 1.555 atm. What is the velocity of the flow?
Water at a temperature of 35 °C is flowing steadily in a 2.5 mm diameter, 15-meter long tube at an average velocity of 0.60 m/sec. The cross-section is circular and the material is perfectly smooth. The flow can be considered fully developed. Find the pressure drop over the length of the tubing, Δ?
Carbon dioxide is being pumped through a smooth pipe at the rate of 3×10-4 kmol/sec for a distance of 2000 m. Ifthe line is isothermal at 323.15 K and the pressure at the entry point is 750 ×103 Pa and at the exit point is 430×103 Pa, what diameter should the pipe has to ensure that the CO2 will be delivered to the end point with the pressure drop experienced. The viscosity of CO2 at 323.15 K is 1.45×10-5kg/m.s. One trial is sufficient given you tell us how you will proceed to achieve an accurate diameter estimate. Hint: for your initial guess, use D in the range of 0.01-0.02 m.
Water at 10 C flows in a 3.5-cm-diameter pipe at a velocity of 1.75 m/s. The Reynolds number for this flow is ?
Water at 10°C (ρ = 999.7 kg/m3 and μ = 1.307 × 10−3 kg/m·s) is flowing steadily in a 5 -cmdiameter, 20-m-long circular stainless steel pipe. Determine(b) for an average velocity of 0.5 m/s, calculate the pressure drop, the head loss, the pumping powerrequired to overcome this pressure drop.
derive the navier stoke equation to Vz (in function r) in a cylindrical pipe with the maksimum radius of a and L as the length of the pipe in a laminar and steady flow
Two incompressible fluids (m1=2m2) are flowing at the same mass flow rates in homogenous pipes with the same diameter. What is the ratio of their Reynolds numbers?
QS: Water at 15.56°C i to be heated in a 2-mm-ID tube until the exit temperature reaches 26.67+C. The tube wall temperature is maintained at 48.99-C and the inlet flow velocity is 0.3 m/s. Calculate the length of tube required in meters to accomplish this heating. Also calculate the total heating required, expressed in watts. Answers: L=0.13 m
Flow Characteritistics( Enternce Effect) Why was there some diagrement between the actual Pitot tube velocity profile and the power law velocity profile?
Water with a density of= 999.7 kg/m3 and absolute viscosity of 1.307 x 10-3 kg/m·s is flowing steadily in a 0.20-cm-diameter, 15-m-long stainless pipe at an average velocity of 1.2 m/s. Find the pumping power (W) requirement to overcome the pressure drop across the span of the pipe. If the flow is laminar, use the figure below to calculate f. If the flow is turbulent, use 0.0741 as the value for f.