Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)
8th Edition
ISBN: 9781305387102
Author: Kreith, Frank; Manglik, Raj M.
Publisher: Cengage Learning
expand_more
expand_more
format_list_bulleted
Videos
Textbook Question
Chapter 6, Problem 6.3P
Steam at 100 kPa and
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
Combustion gases passing through a 5-cm-internal-diameter circular tube are used to vaporize waste water at atmospheric pressure. Hot gases enter the tube at 225 kPa and 250oC at a mean velocity of 2.5 m/s, and leave at 150o If the average heat transfer coefficient is 150 W/m2K and the inner surface temperature of the tube is 110oC, determine (a) the tube length and (b) the rate of evaporation of water.
Air enters a 25-cm-diameter 12-m-long underwater duct at 50°C and 1 atm at a mean velocity of 7 m/s, and is cooled by the water outside. If the average heat transfer coefficient is 85 W/m2?K and the tube temperature is nearly equal to the water temperature of 10°C, determine the exit temperature of air and the rate of heat transfer. Evaluate air properties at a bulk mean temperature of 30°C. Is this a good assumption?
Combustion gases passing through a 3-cminternal- diameter circular tube are used to vaporize waste water at atmospheric pressure. Hot gases enter the tube at 115 kPa and 250°C at a mean velocity of 5 m/s, and leave at 150°C. If the average heat transfer coefficient is 120 W/m2?K and the inner surface temperature of the tube is 110°C, determine (a) the tube length and (b) the rate of evaporation of water.
Chapter 6 Solutions
Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Air enters a 20-cm-diameter 12-m-long underwater duct at 50°C and 1 atm at a mean velocity of 7 m/s, and is cooled by the water outside. If the average heat transfer coefficient is 85 W/m2 °C and the tube temperature is nearly equal to the water temperature of 5°C, determine the exit temperature of air and the rate of heat transferarrow_forwardWater with a mass flow rate of 0.002 kg/s at 18oC flows inside a tube while the flow is already developed hydrodynamically. The inner diameter of the tube is 1.5 cm, and the inner pipe wall temperature is maintained uniformly at 125oC. Calculate the required tube length to increase the water temperature to 82oC.arrow_forwardInside a condenser, there is a bank of seven copper tubes with cooling water flowing in them. Steam condenses at a rate of 0.6 kg/s on the outer surfaces of the tubes that are at a constant temperature of 68°C. Each copper tube is 5-m long and has an inner diameter of 25 mm. Cooling water enters each tube at 5°C and exits at 60°C. Determine the average heat transfer coefficient of the cooling water flowing inside each tube and the cooling water mean velocity needed to achieve the indicated heat transfer rate in the condenser.arrow_forward
- Liquid bismuth flows at a rate of 4.5 kg/s through a 5.0-cm-diameter stainless-steel tube. The bismuth enters at 415◦C and is heated to 440◦C as it passes through the tube. If a constant heat flux is maintained along the tube and the tube wall is at a temperature 20◦C higher than the bismuth bulk temperature, calculate the length of tube required to effect the heat transfearrow_forwardFluid flows at an ambient temperature of 87 oC at a speed of 0.4 m/s through a smooth pipe with a diameter of 20 mm, a length of 24 m and placed horizontally, and heats a medium. Considering that the pipe surface temperature remains constant, inside the pipe; a) In case of water flow,b) In case of engine oil leakage Calculate the heat transfer coefficient and the friction factor in the in-pipe flow and compare and interpret the results.arrow_forwardEngine oil enters a straight tube with a flow rate of 1 kg/s. The tube has a diameter of 5 mm and the surface temperature of the tube is maintained at 150˚C. The engine oil has an inlet temperature 52˚C and it is desired to heat the oil to a mean temperature of 80˚C at the exit of the straight tube. The properties of the engine oil are k = 0.139 W/m.K, Pr = 834, cp = 2072 J/kg.K and μ = 5.62 x 10-2 N.s/m2 Assume the flow is at fully developed region, determine:(a) The required length of the tube. (b) The rate of heat transfers from the tube to the engine oil.arrow_forward
- Consider a 25-mm-diameter and 15-m-long smooth tube that is used for heating fluids. The wall is heated electrically to provide a constant surface heat flux along the entire tube. Fluids enter the tube at 50°C and exit at 150°C. If the mass flow rate is maintained at 0.01 kg/s, determine the convection heat transfer coefficients at the tube outlet for water, engine oil, and liquid mercury.arrow_forwardConsider an air solar collector that is 1 m wide and 5 m longand has a constant spacing of 3 cm between the glass cover andthe collector plate. Air enters the collector at 30°C at a rate of0.15 m3/s through the 1-m-wide edge and flows along the 5-mlong passage way. If the average temperatures of the glasscover and the collector plate are 20°C and 60°C, respectively,determine (a) the net rate of heat transfer to the air in thecollector and (b) the temperature rise of air as it flows throughthe collector.arrow_forwarda)Identifythe maximum velocitylimitof ammonia gas in the pipe if the flow is to be maintained as laminar flow. b)If the actual velocity of ammonia gas is 0.9 times the maximum velocitylimit, calculatethe heat transfer coefficient and heat transfer flux if the heat transfer area is 0.16m^2. c)Suppose the pipe has an outer diameter of 43.1 mm and the outer surface wall temperature of the pipe is 356 K, determinethe thermal resistance and thermal conductivity of the pipe.arrow_forward
- 3. Consider a 10-m-long smooth rectangular tube, with a =50 mm and b =25 mm, that is maintained at a constant surface temperature. Liquid water enters the tube at 20°C with a mass flow rate of 0.01 kg/s. Determine the tube surface temperature necessary to heat the water to the desired outlet temperature of 80°C.arrow_forwardAir at 60°C leaves a furnace and passes through a 12-m long, 20-cm × 20-cm square duct at an average velocity of 4 m/s. If the duct has a constant surface temperature of 33°C, determine the exit temperature of the air and the rate of heat transfer.arrow_forwardIn the effort to find the best way to cool a smooth thin-walled copper tube, an engineer decided to flow air either through the tube or across the outer tube surface. The tube has a diameter of 5 cm, and the surface temperature is maintained constant. Determine (a) the convection heat transfer coefficient when air is flowing through its inside at 25 m/s with bulk mean temperature of 50°C and (b) the convection heat transfer coefficient when air is flowing across its outer surface at 25 m/s with film temperature of 50°C.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Principles of Heat Transfer (Activate Learning wi...Mechanical EngineeringISBN:9781305387102Author:Kreith, Frank; Manglik, Raj M.Publisher:Cengage Learning
Principles of Heat Transfer (Activate Learning wi...
Mechanical Engineering
ISBN:9781305387102
Author:Kreith, Frank; Manglik, Raj M.
Publisher:Cengage Learning
Heat Transfer – Conduction, Convection and Radiation; Author: NG Science;https://www.youtube.com/watch?v=Me60Ti0E_rY;License: Standard youtube license