A 15-cm X 15-cm circuit board dissipating 15 W of power uniformly is cooled by air, which approaches the circuit board at 20°C with a velocity of 5 m/s. Disregarding any heat transfer from the back surface of the board, determine the surface temperature of the electronic components at the end of the board. Assume the flow to be turbulent since the electronic components are expected to act as tabulators.

A 15-cm X 15-cm circuit board dissipating 15 W of power uniformly is cooled by air, which approaches the circuit board at 20°C with a velocity of 5 m/s. Disregarding any heat transfer from the back surface of the board, determine the surface temperature of the electronic components at the end of the board. Assume the flow to be turbulent since the electronic components are expected to act as tabulators.

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter7: Forced Convection Inside Tubes And Ducts

Section: Chapter Questions

Problem 7.22P

See similar textbooks

Similar questions

A 4-m x 4-m flat plate maintained at a constant temperature of 80°C is subjected to parallel flow of air at 1 atm, 20°C, and 10 m/s. The total drag force acting on the upper surface of the plate is measured to be 2.4 N. Using momentum heat transfer analogy, determine the average convection heat transfer coefficient, and the rate of heat transfer between the upper surface of the plate and the air
Air at 60°C leaves a furnace and passes through a 12-m long, 20-cm × 20-cm square duct at an average velocity of 4 m/s. If the duct has a constant surface temperature of 33°C, determine the exit temperature of the air and the rate of heat transfer.
Air enters a 7-m-long section of a rectangular duct of cross section 15 cm X 20 cm at 50°C at an average velocity of 7 m/s. If the walls of the duct are maintained at 10°C, determine: (a) the outlet temperature of the air, (b) the rate of heat transfer from the air, and (c) the fan power needed to overcome the pressure losses in this section of the duct.
Consider an air solar collector that is 1 m wide and 5 m longand has a constant spacing of 3 cm between the glass cover andthe collector plate. Air enters the collector at 30°C at a rate of0.15 m3/s through the 1-m-wide edge and flows along the 5-mlong passage way. If the average temperatures of the glasscover and the collector plate are 20°C and 60°C, respectively,determine (a) the net rate of heat transfer to the air in thecollector and (b) the temperature rise of air as it flows throughthe collector.
An array of power transistors, dissipating 6 W ofpower each, are to be cooled by mounting them on a 25-cm *25-cm-square aluminum plate and blowing air at 35°C overthe plate with a fan at a velocity of 4 m/s. The average temperatureof the plate is not to exceed 65°C. Assuming theheat transfer from the back side of the plate to be negligibleand disregarding radiation, determine the number of transistorsthat can be placed on this plate.
In the effort to increase the removal of heat from a hot surface at 120°C, a cylindrical pin fin (kf = 237 W/m.K) with diameter of 5 mm is attached to the hot surface. Air at 20°C (1 atm) is flowing across the pin fin with a velocity of 10 m/s. Determine the maximum possible rate of heat transfer from the pin fin. Evaluate the air properties at 70°C.
Metal plates (k = 150 W/m·K, ρ= 2800 kg/m3, and cp = 900 J/kg·K) with a thickness of 2 cm exiting an oven are conveyed through a 10-m long cooling chamber at a speed of 4 cm/s, as shown in the figure. The plates enter the cooling chamber at an initial temperature of 500°C. The air temperature in the cooling chamber is 15°C, and the plates are cooled with blowing air and the convection heat transfer coefficient is given as a function of the air velocity h(V) = 33V0.8, where h is in W/m2·K and V is in m/s. To prevent any hazard to workers handling the plates, it is necessary to design the cooling process such that the plates exit the cooling chamber at a relatively safe temperature of 50°C or less. Determine the air velocity V and the heat transfer coefficient h such that the temperature of the plates exiting the cooling chamber is at 50C.
An array of power transistors, dissipating 6W of power each, are to be cooled by mounting them on a 25cm x 25xm square aluminum plate and blowing air at 35o over the plate with a fan at a velocity of 4m/s. The average temperature of the plate is not to exceed 65oC. Assuming the heat transfer from the back side of the plate to be negligible and disregarding radiation, determine the number of transistors that can be placed on the plate. Hint 1: This is a flat plate question. DO NOT treat the transistors as a tube bank. How much heat is dissipated across the flat side of the plate (opposite the side the transistors are mounted on). Hint 2: Use the average Reynold’s and Nusselt numbers
How is volume flow rate different than velocity? What happens to volume flow rate in areas where fluid pressure is high?
3. Consider a 10-m-long smooth rectangular tube, with a =50 mm and b =25 mm, that is maintained at a constant surface temperature. Liquid water enters the tube at 20°C with a mass flow rate of 0.01 kg/s. Determine the tube surface temperature necessary to heat the water to the desired outlet temperature of 80°C.
Hot carbon dioxide exhaust gas at 1 atm is being cooled by flat plates. The gas at 220oC flows in parallel over the upper and lower surfaces of a 1.5-m-long flat plate at a velocity of 3m/s. if the flat plate surface temperature is maintained at 80oC, determine (a) the local convection heat transfer coefficient at 1 m from the leading edge, (b) the average convection heat transfer coefficient over the entire plate, and (c) the total heat flux transfer to the plate.
A 25-cm-diameter stainless steel ball (r = 8055 kg/m3, cp 480 J/kg·°C) is removed from the oven at a uniform temperature of 300°C . The ball is then subjected to the flow of air at 1 atm pressure and 25°C with a velocity of 3 m/s. The surface temperature of the ball eventually drops to 200°C. Determine the average convection heat transfer coefficient during this cooling process and estimate how long the process will take.