1- Air at 288.8 k and 101.32 kPa with a free streamvelocity of 3.05 m/s is flowing parallel to a smoothflat plate held at a surface temperature 333.2 K. Thelength of the flat surface is 0.305 m. Determine totalheat transfer from the plate.Note: This is an external heat convection problem and

Answered: 1- Air at 288.8 k and 101.32 kPa with a…

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter5: Analysis Of Convection Heat Transfer

Section: Chapter Questions

Problem 5.67P

See similar textbooks

Similar questions

5.7 The average Reynolds number for air passing in turbulent flow over a 2-m-long, flat plate is . Under these conditions, the average Nusselt number was found to be equal to 4150. Determine the average heat transfer coefficient for an oil having thermal properties similar to those in Appendix 2, Table 18, at at the same Reynolds number and flowing over the same plate.
Determine the rate of heat loss from the wall of a building resulting from a 16 km/h wind blowing parallel to its surface. The wall is 24 m long and 6 m high, its surface temperature is 27C, and the temperature of the ambient air is 4C.
An electrical transmission line of 1.2-cm diameter carries a current of 200 amps and has a resistance of 310-4 ohm per meter of length. If the air around this line is at v, determine the surface temperature on a windy day, assuming a wind blows across the line at 33 km/h.
7.43 Liquid sodium is to be heated from 500 K to 600 K by passing it at a flow rate of 5.0 kg/s through a 5-cmID tube whose surface is maintained at 620 K. What length of tube is required?
Consider laminar flow of air across a hot circular cylinder. At what point on the cylinder will the heat transfer be highest? What would your answer be if the flow were turbulent?
Liquid mercury at 250°C is flowing with a velocity of 0.3 m/s in parallel over a 0.1-m-long flat plate where there is an unheated starting length of 5 cm. The heated section of the flat plate is maintained at a constant temperature of 50°C. Determine (a) the local convection heat transfer coefficient at the trailing edge, (b) the average convection heat transfer coefficient for the heated section, and (c) the rate of heat transfer per unit width for the heated section.
Please help with this questionHot carbon dioxide exhaust gas at 1 atm is being cooled by flat plates. Thegas at 220°C flow is parallel over the upper and lower surfaces of a 3-m-longflat plate at a velocity of 3 m/s. If the flat plate surface temperature ismaintained at 80°C.Determine the local convection heat transfer coefficient at 1 m fromthe leading edge and calculate the average convection heat transfer coefficient over theentire plate.
Air at 60°F flows over a 10-ft-long flat plate at 7 ft/s. Determine the local friction and heat transfer coefficients at intervals of 1 ft, and plot the results against the distance from the leading edge.
Consider atmospheric air at 25?C and a velocity of 25 m/s flowing over both surfaces of a 1-m-long flat plate that is maintained at 125?C. Determine the rate of heat transfer per unit width from the plate for values of the critical Reynolds number corresponding to 5×105
Air at 27 ⁰C and 1 atm flows over a flat plate at a velocity of 3m/s, assuming the plate is heated its entire length to a temperature of 70⁰C. Heat transferred in first 25 cm of the plate is?
The airflow at 1 atm has a free stream velocity and temperature of 5 cm/s and 25°C, respectively. Determine the heat flux on the plate surface and the convection heat transfer coefficient of the airflow.
Air is flowing in parallel over the upper surface of aflat plate with a length of 4 m. The first half of the plate length,from the leading edge, has a constant surface temperatureof 50°C. The second half of the plate length is subjected toa uniform heat flux of 86 W/m2. The air has a free streamvelocity and temperature of 2 m/s and 10°C, respectively.Determine the local convection heat transfer coefficients at1 m and 3 m from the leading edge. Evaluate the air propertiesat a film temperature of 30°C. Is the film temperatureTf = 30°C applicable at x = 3 m?

SEE MORE QUESTIONS

Recommended textbooks for you

Principles of Heat Transfer (Activate Learning wi…

Mechanical Engineering

ISBN:

9781305387102

Author:

Kreith, Frank; Manglik, Raj M.

Publisher:

Cengage Learning