A 15 m building use cast iron pipes in their piping system. The water tank located on the top of the building and will distribute the water to the toilet on the ground level. The water will move in a horizontal 18.5 long and 0.75cm radius pipe before reach the water tab. Take the kinematic viscosity of water = 1.6191 mm2/s. Calculate the flow rate of the water coming out from the tab and determine the condition of the water flow.

A 15 m building use cast iron pipes in their piping system. The water tank located on the top of the building and will distribute the water to the toilet on the ground level. The water will move in a horizontal 18.5 long and 0.75cm radius pipe before reach the water tab. Take the kinematic viscosity of water = 1.6191 mm2/s. Calculate the flow rate of the water coming out from the tab and determine the condition of the water flow.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The velocity through the centre-line of a 150 mm diameter pipe conveying oil under laminar flow conditions is 3 m/s. The viscosity of the oil is 1.2 poises and its density if 900 kg/m3 . Confirm that the flow is laminar and determine (a) the quantity flowing in dm³/s, and (b) the shear stress in the oil at the pipe wall in N/m²
The ethanol solution is pumped into a vessel 25 m above the reference point through a 25 mm diameter steel pipe at a rate of 8 m3 / hr. The pipe length is 40 m and there are 2 elbows. Calculate the power requirements of the pump. The properties of the solution are density 975 kg / m3 and viscosity 4x 10-4 Pa s. a. Reynold number = Answer. b. Loss of Energy along the straight pipe = AnswerJ / kg. c. Losing Energy at curves = AnswerJ / kg. d. Total energy to overcome friction = AnswerJ / kg. e. Energy to increase water according to height = AnswerJ / kg. f. The theoretical energy requirement of the pump ethanol / second = AnswerJ / kg. g. Actual pump power requirement = Answerwatt.
What is the maximum liquid water depth for a laminar flow if the flow speed is 0.01 m/s? (The density of water is still 1000 kg/m3, and it has a viscosity of 0.001 kg/(m*s).)
An oil gusher shoots crude oil 23.0 m into the air through a pipe with a 0.100 m diameter. Neglecting air resistance but not the resistance of the pipe, and assuming laminar flow, calculate the pressure (in N/m2) at the entrance of the 45.0 m long vertical pipe. Take the density of the oil to be 900 kg/m3 and its viscosity to be 1.00 (N/m2) · s (or 1.00 Pa · s). Note that you must take into account the pressure due to the 45.0 m column of oil in the pipe.
The ethanol solution is pumped into a vessel 25 m above the reference point through a 25 mm diameter steel pipe at a rate of 10 m3 / hr. The pipe length is 35m and there are 2 elbows. Calculate the power requirements of the pump. The properties of the solution are density 975 kg / m3 and viscosity 4x 10-4 Pa s. a. Reynold number = Answer b. Loss of Energy along the straight pipe = Answer J / kg. c. Losing Energy at curves = Answer J / kg. d. Total energy to overcome friction = Answer J / kg. e. Energy to increase water according to height = Answer J / kg. f. The theoretical energy requirement of the pump ethanol / second = Answer J / kg. g. Actual pump power requirement = Answer watt.
The ethanol solution is pumped into a vessel 25 m above the reference point through a 25 mm diameter steel pipe at a rate of 8 m3 / hr. The pipe length is 40 m and there are 2 elbows. Calculate the power requirements of the pump. The properties of the solution are density 975 kg / m3 and viscosity 4x 10-4 Pa s. a. Reynold number = Answer. b. Loss of Energy along the straight pipe = Answer J / kg. c. Energy Loss at curves = Answer J / kg. d. Total energy to overcome friction = Answer J / kg. e. Energy to increase water according to height = Answer J / kg. f. The theoretical energy requirement for the pump is kg ethanol / second = Answer J / kg. g. Actual pump power requirement = Answer watt.
A pipe whose axis is horizontal, is full of water in motion. At a section A, the velocity of water is recorded as 54000dm/hrandd the pressure is equilavent tp 14.07m of water. if the pipe tapers gradually from 150mm diameter to A to 100mm diameter at B. determine the preesure at B.
Q6) The space between two parallel plates is filled with oil. Each side of the plate is 60 cm. the thickness of oil film is 12.5 mm. The upper plate, which moves at 2.5 metre per sec requires a force of 98.1 N to maintain the Speed. Determine
Consider the flow of a fluid with viscosity m through a circular pipe. The velocity profile in the pipe is given as u(r) = umax(1 - rn/Rn), where umax is the maximum flow velocity, which occurs at the centerline; r is the radial distance from the centerline; and u(r) is the flow velocity at any position r. Develop a relation for the drag force exerted on the pipe wall by the fluid in the flow direction per unit length of the pipe.
1.3 A pipe discharges 142 lps of water into a reservoir at a point 1.85 m below the water surface. At point A the diameter is 25.4 cm and the center of the pipe is 1.25 m above the water surface. At the discharge end the pipe is 30.5 cm. If the head loss from A to the reservoir is 0.7 m, determine the pressure in A. 1.4 The absolute viscosity of a fluid at atmospheric conditions is 8 x 10-3 kgf-s/m2. Find this viscosity in: a) Reyn; b) Poise; c) lbf-s/ft2; d) Pa-s.
Oil that has a density of 880 kg/m3 flows under a head of 30 m. The pipe that the oil flows through is 3000 m long and 0.35 m in diameter. Due to the cooling along the span of the pipe the viscosity changes, this may be taken as 0.57 kg/m-s over the first 1500 m and 1.14 kg/m-s over the second 1500 m. Confirm that laminar flow conditions exist and calculate the flow in dm³/s. Neglect entry and exit losses.
The space between the shaft and sleeve is filled with an oil of viscosity 6.5 stokes and density 900 kg/m3. The diameter of the shaft is 45 cm and rotates at the speed of 180 RPM. Determine the thickness of oil film between shaft and sleeve and power lost in bearing if the torque transmitted is 80 N-m and length of the sleeve is 100 mm.