A 150-kg container starts from rest in positions = 0. A horizontal force (in newton) that is exerted on the container by a hydraulic piston (assuming the container and the hydraulic piston are situated in a straight line along the position axis s) is given by F= 500 – 100s. The coefficient of kinetic friction between the container and the floor is Uk = 0.2. What is the velocity of the container when it has reached the position s 0.5 m? %3D

A 150-kg container starts from rest in positions = 0. A horizontal force (in newton) that is exerted on the container by a hydraulic piston (assuming the container and the hydraulic piston are situated in a straight line along the position axis s) is given by F= 500 – 100s. The coefficient of kinetic friction between the container and the floor is Uk = 0.2. What is the velocity of the container when it has reached the position s 0.5 m? %3D

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The drum has a weight of 100 lb and rests on the floor for which the coefficient of static friction is 0.6. If a=2ft and b=3 ft, determine the smallest magnitude of the force P that will cause impending motion of the drum.
The ladder and the person weigh 30 lb and 180 lb, respectively. The center of mass of the 1-2ft ladder is at its midpoint.The coefficient of static friction between the ladder and the floor is 0.5 and the coefficient of friction between the ladder and the wall is 0.3. What is the largest value of angle ALPHA for which the person could climb to the top of the ladder without it slipping?
An 80-kg block rests on a horizontal plane. Find the magnitude of the force P required to give the block an acceleration of 2.5m/s² to the right. The coefficient of kinetic friction between the block and the plane is μk = 0.25.
A 200-lb block is on top of a 300-lb block and both blocks are tied to a pulleya pulley that is attached to the wall, as shown in the figure. The coefficient of static friction between thetwo blocks is 0.3 and between the 300 lb block and the floor is 0.4. The coefficient of dynamic frictionbetween all surfaces is 0.25. Disregard the friction at the pulley.Determine the minimum force that must be applied to the 300 lb block in order for it to initiatemotion (imminent motion).
The 20 lb box falls off the conveyor belt at 3 ft/s . If the coefficient of kinetic friction along AB is μk=0.25 determine the distance x when the box falls into the cart.
The wooden block (mass m = 0.5358 kg) is released from rest at A by a compressed spring (compressed length 0.6 m, undeformed length 1 m, spring constant k = 150 N/m). The block is allowed to slide through the rough horizontal surface (A to B), then along the smooth circular ramp (B to C, central angle θ = 47.2°, until the block is released after point C. Calculate the speed of the block at points B and C. Also, what is the magnitude of the normal force exerted to the block just before the block leaves the ramp? Neglect the geometry of the block.NOTE: Use Work-Energy Method to solve for the speeds; use Force-Mass-Acceleration (FMA) Method to compute for the normal force.
A stepladder consisting of two legs pinned together at C is resting on a rough floor. Will a 800 N worker be able to change the light bulb if he is required to climb to a height of 1.3 m? The uniform legs AC and BC weigh 110 N and 70 N, respectively. The coefficient of static friction at Aand B is 0.48.
a stepladder consisting of two legs pinned together at C is resting on a rough floor. will 800 N worker be able to change the light bulb if he is required to climbed to a height of 1.3 m? The uniform legs AC and BC weigh 110 N and 70 N, respectively. the coefficient of static friction is 0.48
The mass of block B is 95kg while that of A is 59kg. A horizontal force P=468N is applied at block A. The cutting angle is 30.296 degrees. Neglect friction. Computations must observe D`Alembert's Principle. a) Determine the normal force of contact between block A and block B. Express answer in Newtons or KiloNewtons.b) Determine the acceleration of block A. Express answer in meters per seconds.c) Determine the acceleration of block B. Express answer in meters per seconds.
The ladder and the person weigh 30 lb and 180 lb, respectively. The center ofmass of the 12-ft ladder is at its midpoint. The coefficient of static frictionbetween the ladder and the floor is 0.5 and the coefficient of friction betweenthe ladder and the wall is 0.3. What is the largest value of the angle ALPHA for which the person could climb to the top of the ladder without it slipping?
FLUID MECHANICS: MOMENTUM EQUATION A cone that is held stable by a wire is free to move in the vertical direction and has a jet of water (at 10oC) striking it firm below. The cone weighs 30 N. The initial speed of the jet as it comes from the orifice is 15m/s, and the initial jet diameter is 2cm. Find the height to which the cone will rise and remain stationary. NOTE: The wire is only for stability and should not enter your calculations.
At the instant θ = 30 degrees, the 10 Kg slender bar of length L =0.9 m has a clockwise angular velocity of 2.5 rad/s. The coefficient of kinetic friction at end B is 0.22; end A is attached to a massless roller that rolls on the smooth horizontal plane. Answer the following, 1) find the angular acceleration 2) Reaction forced at A and B 3) horizontal and vertical components of acceleration of the rod's center of mass