A 150 mm diameter open circular cylinder is 1 m long and contains water up to a height of 0.7 m. Estimate the speed at which the cylinder may be rotated about its vertical axis so that the axial depth becomes zero. a. 249. b. 163.93 c. 564 d. 296

A 150 mm diameter open circular cylinder is 1 m long and contains water up to a height of 0.7 m. Estimate the speed at which the cylinder may be rotated about its vertical axis so that the axial depth becomes zero. a. 249. b. 163.93 c. 564 d. 296

Name: A 150 mm diameter open circular cylinder is 1 m long and contains wate
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: A 150 mm diameter open circular cylinder is 1 m long and contains water up to a height of 0.7 m. Estimate the speed at which the cylinder may be rotated about its vertical axis so that the axial depth becomes zero.a. 249.b. 163.93c. 564d. 296

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter8: Centroids And Distributed Loads

Section: Chapter Questions

Problem 8.122P: The 12-ft wide quarter-circular gate AB is hinged at A. Determine the contact force between the gate...

See similar textbooks

Similar questions

A 12-fl -oz glass, of 3-in diameter, partly full of water, isattached to the edge of an 8-ft-diameter merry-go-round,which is rotated at 12 r/min. How full can the glass bebefore water spills? Hint: Assume that the glass is muchsmaller than the radius of the merry-go-round.
A horizontal cylinder of internal diameter 100 mm is filled with water and rotated about its axis with an angular velocity of 3000 rpm. Calculate the pressure at the ends of the horizontal and vertical diameter. (Answer: *ends of horizontal diameter = 124.1 kN/m2, *vertical diameter; top end = 123.6 kN/m2, bottom end = 124.6 kN/m2)
The 5-m wide sluice gate “ab” shown, tangent to the vertical wall at “a”, holds back water. The surface of the gate in contact with the water can be taken as part of a cylinder with radius 4 m. a. Determine the horizontal force acting on the curve. b. Determine the total force on the curve. c. Determine the location of the vertical force from pt. “a”.
Determine the angular velocity (in rpm) required for an open 100-cm diameter cylindrical tank 250cm high if it contains water 150cm deep at the following condition.When there is no water at the bottom surface of the tank within 20cm from the centerline / axis of rotation. Group of answer choices 158.69 rpm 179.61 rpm 145.94 rpm 195.44 rpm
End D of a 2.5 long uniformly plain wooden rod( s.g=0.7) is held 0.3m below the surface of still water. (a.) How much of the rod remains above the water surface? (b.) if the rod diameter is 25mm what force of D is required to hold it in place ?
A rectangular car is 3 m. long by 1.5 m wide and 1.5 m deep. If friction is neglected and the car rolls down a plane with an inclination of 20 degrees, what is the inclination of the water surface if the car contained 0.60 m depth of water when the car was horizontal?
A long solid cylinder of radius 0.8 m hinged at point A is used as an automatic gate, When the water level reaches 5 m, the gate opens by turning about the hinge at point A. Determine (a) the hydrostatic force acting on the cylinder and its line of action when the gate opens and (b) the weight of the cylinder per m length of the cylinder.
A dam with triangular cross section holds back a body of water. The dam has height h. The dam is made of concrete, which has speci…c gravity 3.1. What is the maximum angle, , for which thedam will not tip over about point O?
Provide complete solution and diagram for this problem. What is the equivalent head of 15cm mercury in water ? A. 10m B. 1.36m C. 2.04m D. 16.34m
A 6-m-high, 5-m-wide rectangular plate blocks the end of a 5-m-deep freshwater channel, as shown . The plate is hinged about a horizontal axis along its upper edge through a point A and is restrained from opening by a fixed ridge at point B. Determine the force exerted on the plate by the ridge
The sluice gate shown is a circular arc of radius 6m and angle B=50o. The water level behind the gate flushes to the gate’s top most edge. Knowing that the length of the gate is 5m (dimension perpendicular to the paper), determine the vertical component of the hydrostatic force acting on the gate. a) 84.73kN b) 97.65kN c) 63.45 kN d) 94.12kN e) None
If the rate of rotational speed of the 3-tube system shown is ? = 10 rad/s, determine the water heights in each tube leg. At what rotational speed will the middle tube be completely empty?