A 1500KVA, 8KV, three-phase wye-connected alternator has an effective resistance of 0.502 and a reactance of 62 per phase. It delivers full-load current at 0.8 lagging power factor at rated voltage. What will be the terminal voltage for the same excitation and load current, if the power factor is 0.8 leading?

A 1500KVA, 8KV, three-phase wye-connected alternator has an effective resistance of 0.502 and a reactance of 62 per phase. It delivers full-load current at 0.8 lagging power factor at rated voltage. What will be the terminal voltage for the same excitation and load current, if the power factor is 0.8 leading?

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.41P

See similar textbooks

Similar questions

Consider two interconnected voltage sources connected by a line of impedance Z=jX, as shown in Figure 2.27. (a) Obtain expressions for P12 and Q12. (b) Determine the maximum power transfer and the condition for it to
A 3-phase, wye connected alternator rated at 1600 kVA, 13.5 kV. The effective armature resistance and synchronous reactance are 1.5 ohms and 30 ohms, respectively. What is the percent regulation for a load of 1280 kW at 0.80 leading power factor?
A 4MVA, 13.3kV, 60Hz, 3-phase, wye-connected alternator has an effective resistance of 5.2 ohm per phase and a combined armature reactance of 10.4 ohm per phase. Determine the full load Voltage regulation (in %) at unity pf.
q1: Discussion of power quality aspects that need to be considered before installing the power factor correction unit
A 15kVA, 440V, single-phase alternator draws a field current of 5A at rated load. With the same field current, the open circuit emf and short-circuit current are 100V and 80A respectively. The ohmic resistance of the armature between terminals is 0.12 ohm. The ratio of effective to ohmic resistance maybe taken as 1.1. Determine the voltage regulation (in %) when the load is purely resistive.
The effective resistance of a 2200 V, 50 Hz, 440 KVA, 1 -phase alternator is 0.5 ohm. On short-circuit, a field current of 40 A gives the full load current of 200 AS. The electromotive force on open-circuits with same field excitation is 1160 V. Then the synchronous impedance and reactance is _______ ohm and _______ ohm respectively.
Consider the single-phase three-wire system shown. Find the current in the neutral wire and the complex power supplied by each source. Take V, as a 115∠0° V, 60-Hz source.
A single-phase alternator connected to 6,600-V bus-bars has a synchronous impedance of 10Ω and a resistance of 1 Ω. If its excitation is such that on open circuit the p.d. would be 5000 V, calculate the maximum load the machine can supply to the external circuit before dropping out of step and the corresponding armature current and p.f. [2864 kW, 787 A, 0.551]
A straight-line law connects terminal voltage and load of a 3-phase star connected alternator delivering current at 0.8 power factor lagging. At no-load, the terminal voltage is 3,500 V and at full-load of 2,280 kW, it is 3,300 V. Calculate the terminal voltage when delivering current to a 3-phase, star-connected load having a resistance of 8 o and a reactance of 6 ohm per phase. Assume constant speed and field excitation.
L-type equivalent circuit and parameters for a continuous sinusoidal phase of a 5.5 kW, 1450 rpm, line voltage 220 V and frequency 50 Hz star-connected 3-phase ASM, ignoring core (iron) losses given as follows: R1=0.21 Ohm, R2=0.18 Ohm, X1=X2=0.66 Ohm and Xm=9.9 Ohm How many times the rated current will the inrush current be when the ASM is started directly?
Two impedances Z 1 and Z 2 , when connected separately across a 230 volt, 50 Hz supply consumed 100 watts and 60 watts at power factors of 0.5 lagging and 0.6 leading respectively. If these impedances are connected in parallel across 230 volt, 60 Hz supply, find: (a) total power absorbed and overall power factor; (b) the value of a reactance to be further connected in series with the two to make the overall power factor to be unity.COMPLETE SOLUTION PLEASE
What are the typical power quality issues in the power system? What are the methods to mitigate such issues?