A 2-m diameter, open cylindrical tank has its height that is twice its diameter and is 75% filled with water. It is rotated about its geometric axis with a constant angular speed, w. Determine the angular speed in rpm if: a.) there is no water spilled b.) the vertex of the paraboloid just touches the bottom of the tank c.) the volume spilled is 1979 liters.

A 2-m diameter, open cylindrical tank has its height that is twice its diameter and is 75% filled with water. It is rotated about its geometric axis with a constant angular speed, w. Determine the angular speed in rpm if: a.) there is no water spilled b.) the vertex of the paraboloid just touches the bottom of the tank c.) the volume spilled is 1979 liters.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A 50 mm diameter circular sharp-edged orifice at the side of a tank discharges water under a head of 3 m. If the coefficient of contraction Cc=0.63 and the headlost is 240 mm, compute the discharge and the coefficients of velocity Cv and discharge C.
An open cylindrical vessel 1.20m in diameter and 2.10m high is 2/3 full of water. If the vessel is rotated about its vertical axis at a constant speed of 90rpm, compute:The height of the paraboloid the water at a constant speed of 90rpm rotation.
The tank shown in figure is of a depth d = 48.8 cm and width w =24.4 cm accelerated by ax = 3.43m/sec2 to the right, find the allowable water height (h) to avoid spill of water during acceleration
Determine the radius of the orifice that will allow a tank of horizontal cross-section of 2.5 m^2 to have its liquid surface draw down at the rate of 0.2 m/s for a constant head of 4m on the orifice with Cc= 0.66 and Cv= 0.96
A cylindrical vessel 15 cm diameter and 40 cm long is completely filled with water. The vessel is open at the top. Find the quantity of water left in the vessel in cm^3, when it is rotated about its vertical axis with a speed of 300 rpm.
diameter of cylindrical tank = 2 meters depth of cylindrical tank = 8 meters diameter of sharp-edge orifice = 100 mm The standard orifice is placed at the side 1 meter above the bottom. When at rest, the depth of water is 5 meters Considering that the volume of water is constant, what is the rate of discharges from the standard orifice: a. When the cylindrical tank has a constant velocity of 3 m/sec in the opposite direction of the jet. b. When the cylindrical tank has a constant acceleration of 6 m/sec^2 in the opposite direction of the jet. Consider the figures below*
8. A tank has a length of 2.5 m and width of 2.0 m and contains water at a depth of 1.15 m. If the tank is subjected to an linear acceleration of 4.25 m/s-2 parallel to the length of the tank, determine the height of the sides such that no water will be spilled.
a cylindrical tank is span at 300 rpm its axis vertical. the tank is 0.6 m high and 45cm diameter and is completely filled with water before spinning. calculate the level to which the water will return when the tank stops spinning
Determine the diameter of an orifice that permits a tank of horizontal cross- section 1.5m2 to have its liquid surface draw down at the rate of 160 mm/s for a 3.35-m head on the orifice. Use C=0.63.
4. An open cylindrical tank 2 m in diameter and 4 m high contains water to a depth of 3 m. It is rotated about its own vertical axis with a constant angular speed. a. If w = 8 rad/s, how much water is spilled out and to what depth will the water stand when brought to rest?b.What angular speed w (in rpm) will just zero the depth of water at the center or the tank?c.If w = 100 rpm, how much area at the bottom of the tank is uncovered?
A tank has one of its side inclined inward at an angle of 30 degrees with horizontal. The free surface of the contained water is at Elev 15.25 m. The orifice located on the inclined side issues a jet, having its vena contracta at Elev 10.70 m. If the highest point in the trajectory of the jet is at Elev. 14.00m, find the actual velocity of the jet. Neglect air friction. a. 11.3 m/s b. 9.3 m/s c. 8.3 m/s d. 10.3 m/s
A 1.90m diameter closed cylinder, 2.75m high is completely filled with oil having sp.gr. of 0.8 under a pressure of 5 kg/cm^2 at the top. a. What angular speed (RPM) can be imposed on the cylinder so that the maximum pressure at .90 m from the center of the tank is 14 kg/cm^2 ? b. If the cylinder is open what is the maximum angular speed (RPM) can be imposed so that the water touches the bottom of the tank?