Axial Load, P(kN) A 2 m long axially loaded mild steel rod of 8 mm diameter exhibits the load-displacement (P -8) behavior as shown in the figure. 14000 12000 10000 8000 6000 4000 2000 0 1 2 7 8 9 10 3 4 5 6 Displacement 8(mm) Assume the yield stress of steel as 250 MPa. The complementary strain energy (in N-mm) stored in the bar up to its linear elastic behavior will be

Axial Load, P(kN) A 2 m long axially loaded mild steel rod of 8 mm diameter exhibits the load-displacement (P -8) behavior as shown in the figure. 14000 12000 10000 8000 6000 4000 2000 0 1 2 7 8 9 10 3 4 5 6 Displacement 8(mm) Assume the yield stress of steel as 250 MPa. The complementary strain energy (in N-mm) stored in the bar up to its linear elastic behavior will be

Materials Science And Engineering Properties

1st Edition

ISBN:9781111988609

Author:Charles Gilmore

Publisher:Charles Gilmore

Chapter6: Introduction To Mechanical Properties

Section: Chapter Questions

Problem 6.2P

See similar textbooks

Similar questions

In the bar system in the figure, the material is ideal elasto-plastic and the yield stress is given as σA = 440 Mpa. Since the cross-sectional areas of the rods number one and two are given as A = 250 mm2, find the force P (kN) that will bring the system to the yield point. (a = 5m b = 1m) please fast help
According to σgüv= 700N/cm2 and tgüv = 100 N/cm2 in the material of the output beam given the loading condition, cross-section and dimensions in the figure; a) Find the largest Q-spread load that can be safely transported. b) Draw a diagram of shear stress in cross-section. (Note: for all odd values, two digits will be taken after the point.)
A hollow aluminum tube used in a roof structure has an outside diameter d2= 112mm and an inside diameter d1= 80mm. The tube is 2.80m long, and the aluminum has a shear modulus of G= 28GPa.a. If the tube is twisted in pure torsion by torques acting at the ends, what is the angle of twist, in degrees,when the maximum shear stress is 52MPa?b. What diameter d, in mm, is required for a solid shaft, as shown, to resists the same torque with the same maximum stress?c. What is the ratio of the weight of the hollow tube to the weight of the solid shaft?
Figure Q3 (a) shows a cantilevered beam ABC carrying a pure moment of M kN.m at point B. Thecross-sectional area of the beam is shown in Figure Q3 (b). The yield stress of the material is 250 MPa and the material is assumed to behave linearly elastic-perfectly plastic.a) Where is the critical location for the beam and give ONLY ONE (1) reasonb) Determine the moment to initiate yielding in the cross-section of the beamc) Find the value of M that can cause plastic collapse (fully plastic) in the cross-section of the beamat the critical location and sketch the variation of stressd) If the TOTAL DEPTH of the plastic zone to be 20 mm at the critical location, WITHOUT ANYCALCULATION, sketch the variation of stress.
A hollow steel (E= 30,000ksi) tube (1) with an outside diameter of 2.75in. and a wall thickness of 0.25in. is fastened to a solid aluminum (E= 10,000 ksi) rod (2) that has a 2in. diameter and a solid 1.375in. diameter aluminum rod (3). The bar is loaded as shown in the figure. Determine (a) the change in length of steel tube (1); (b) the deflection of joint D with respect to the fixed support A. (c) the maximum normal stress in the entire axial assembly.
Two solid cylindrical rods AB and BC are welded together at B and loaded as shown. Determine the magnitude of the force P (in lb) for which the tensile stress in rod AB is thrice the magnitude of the compressive stress in rod BC if Q = 20.11 lb.
A steel bar 25cm long of rectangular cross section 25mm by 50mm is subjected to a uniform tensile stress of 200N/m^2 along it's length.find the changes in dimension.E=205000N/mm^2, poison ratio=0.3
In the bar system in the figure, the material is ideal elasto-plastic and the yield stress is given as σA = 440 Mpa. Since the cross-sectional areas of the rods number one and two are given as A = 250 mm2, find the force P (kN) that will bring the system to the yield point. (a = 5m b = 1m)
Refer to figure STR - 5 Two prismatic bars are rigidly fastened together and support a vertical load of 45kN. The upper bar is of steel having mass density 7750 kg/m^3 , length 10m and cross-sectional area 65 cm^2. The lower bar is of brass having mass density 9000kg/m^3, length 6m and cross-sectional area 50 cm^2. Determine the maximum stress in each material. For steel Es= 200 GN/m^2 and for brass Eb= 100 GN/m^2. I need answer ASAP. Thank you!
1. A 18-mm-diameter steel wire 150 m long, is suspended vertically from one end. It supports a tensile load of 12 kN at the lower end. Neglect the weight of the wire. Use E =200,000 MPa.a. Find the stress in the wire in MPa.b. Find the elongation of the wire in mm.
The pin‐connected assembly shown in Figure below consists of solid aluminum [E = 70 GPa] rods (1) and (2) and solid steel [E = 200 GPa] rod (3). Each rod has a diameter of 16 mm. Assume that a = 2.5 m, b = 1.6 m, and c = 0.8 m. If the normal stress in rod (1) must not exceed 150 MPa, determine (a) the maximum load P that may be applied at A. (b) the magnitude of the resulting deflection at A.
Mechanics of Deformable Bodies. Two solid cylindrical rods AB and BC are welded together at B and loaded as shown. Knowing that d1 5 30 mm and d2 5 50 mm, find the average normal stress at the midsection of (a) rod AB, (b) rod BC.