A 2.00-kg block is pushed against a spring with negligible mass and force constant compressing it 0.220 m. When the block is released, it moves along a frictionless, horizontal surface and then up a frictionless incline with slope 370. How far does the block travel up the incline before starting to slide back down? A. 1.16 m k = 400 Njm = 2.00 kg wwwA В. 0.82 m 37.0 С. 3.1 m K-0.20 mH D. 1.2 m Е. 2 m

A 2.00-kg block is pushed against a spring with negligible mass and force constant compressing it 0.220 m. When the block is released, it moves along a frictionless, horizontal surface and then up a frictionless incline with slope 370. How far does the block travel up the incline before starting to slide back down? A. 1.16 m k = 400 Njm = 2.00 kg wwwA В. 0.82 m 37.0 С. 3.1 m K-0.20 mH D. 1.2 m Е. 2 m

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Please Take Care. Provide Handwritten Solution.
Mass 80 kg
Q3: A car with mass of 800 Kg moves around a 700 m-radius curve at a constant speed of 60 Km/h. If the road is not banked, what frictional force must the road exert on the tires so that they will keep the car along the curve?
3.2 Sliding blocks with friction* Mass MA = 4kg rests on top of mass Mg = 5 kg that rests on a fric- tionless table. The coefficient of friction between the two blocks is such that the blocks just start to slip when the horizontal force F applied to the lower block is 27 N. Suppose that now a horizontal force is applied to the upper block. What is its maximum value for the blocks to slide without slipping relative to each other?
Looking for simple solution with correct answer.
The pulley assembly shown in the figure weighs 150 lb and has a centroidal radius of gyrationof 2 ft. The blocks are attached to the assembly by cords wrapped around the pulleys.Determine the acceleration of each body and the tension in each cord.a. Identify the direction of motion in the problem. 1)b. Set up the equations of motion that is required to solve the problem. SO1.5)c. Solve for the unknown variables by substituting the given in the equations of motionthat has been set up previously.
In reference to the figure below, if uk = 0.7 at the rear drive wheels B of the 1550 lb race car with the mass center at G, 0.75 ft G 6 ft Determine: a) the car's acceleration in ft/s² Express the final answer in 3 significant digits. 4.75 ft- B
The friction coefficient between the 3kg object and the 2kg blocks in the figure is 0.3. the horizontal plane and the rollers are frictionless and the masses move from rest. a) Find the acceleration of each blokları by showing the forces acting on each block (free body diagram). b) Find the tension in the ropes. (g = 3,8m / s^2)
please answer this question with explination. many thanks !
3-B Problem 4 The dredger is loading sand (SG = 2.6) onto a barge. The sand leaves the dredger pipe at 1.2 m/s with a weight flux of 3780 N/s. Estimate the tension on the mooring line caused by this loading process. Ans. 404.8 N 30°
Block 1 (19 kg) is setting on the floor of an elevator. A rope pulls vertically up on block 1 with a tension of 10 N. The elevator is moving downward with a decreasing speed and the magnitude of the acceleration is 2 m/s2.On a sheet of paper, draw the free body diagram for block 1 using the two-subscript notation from class. After completing the free body diagram, enter below each force and its x & y-components. Remember that the x-component is the "i" component and the y-component is the "j" component. NET force on Block 1Fnet1 = i + j N FORCES on BLOCK 1Weight force on block 1 by EarthW1E = i + j N Tension Force on block 1 by RopeT1R = i + j N Normal force on block 1 by SurfaceN1S = i + j N