Solve correct please 3.shown.Calculate the the fluid velocity in the smaller conduit (A 20 in) for the fluid systemA-20 in.OilSG- 0.865t0.8ftA-50 in.2SG 2.5

Answered: Image /qna-images/answer/4366d77c-3d61-44b0-885a-d347ab43b912.jpg

Answered: A-20 in Oil SG 0.86 51t 0.8 t A-50 in.…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Gasoline at 38°C is being drawn from a closed tank having a pressure of 70kPag. The level of gasoline in the tank is 2.5m above the pump centerline. The suction line friction loss is 0.6m. The vapor pressure of the gasoline is 48kPa absolute and its specific gravity is 0.72. Determine the NPSH available.
The 28-in-diameter pump in Fig. at 1170 r/min isused to pump water at 20°C through a piping system at14,000 gal/min. (a) Determine the required brake horsepower.The average friction factor is 0.018. (b) If there is65 ft of 12-in-diameter pipe upstream of the pump, how farbelow the surface should the pump inlet be placed to avoidcavitation?
A centrifugal pump delivers water at a rate of 0.03 m^ 3 / s to a height of 18 meters through a pipe of 100 mm diameter and 90 m long. If the overall efficiency of the pump is 75 %, find the power required to drive the pump. (Take f=0.012) .
a pumping station working with a pump head of 25m. the output power of the motor for that pump is 16kw. identify the pump efficiency if the sewarge discharge velocity is 0.27 m/s and the pipe diameter is 250 mm
Q:/ Discuss the relation betwveen the head pressure and flow rate for the benefits of connecting the pumps in parallel ?
In order to drain the tank faster, a pump is installed near thetank exit. Determine how much power input is necessary toestablish an average water velocity of 4 m/s when the tank isfull at 2 m. diameter is 10cm
A pump delivers water, density =1000kg/m3, at a volume flow rate of 0.004256 m3/sec. If the head developed by the pump is 4.01 m, determine the fluid power in Watts. Take g=9.81 m/s2. State the answer to two decimal places.
How do u get the H pump equation ?. Please write the detail
Find the power required to drive the pump which delivers 0.04 m^3/s of water at the height of 20 m through 15 cm diameter pipe and 100 m long. The overall efficiency of the pump is 70 % and the coefficient of friction is 0.015.
In the figure shown, the flow rate is 0.05 m'/s, determine: (a) pressure at A and B, (b) the machine in this system, is it pump or turbine? Explain it by calculations. [Neglect minor losses).
A pump draws 24 li/s of water from the lower reservoir and lifts it to upper reservoir. The head lossfrom the inlet 150 mm pipe diameter is three times the velocity head and the head loss going to theoutlet 100mm pipe diameter is 25 times its velocity head. What is the power generated by the pump tothe system in horsepower. (Note: Velocities from the reservoir are different from the velocities of thepipe and pleaseee draw a diagram if you can thank you so much)
The figure shows a portion of a fire protection system in which a pump draws water at 60°F(v=1.21 x10-5 m² from a reservoir and delivers it to a point B at the flow rate of 1500 gal/min. Calculate the required height of the the water level in the tank in order to maintain 5.0 Psig pressure at point A

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS

A-20 in Oil SG 0.86 51t 0.8 t A-50 in. SG 2.5