A 200-volt electromotive force is applied to an RC-series circuit in which the resistance is 1000 ohms and the capacitance is 5 x 10-6 farad. Find the charge q(t) on the capacitor if i(0) = 0.2. q(t) = Determine the charge at t = 0.004 s. (Round your answer to five decimal places.) coulombs Determine the current at t = 0.004 s. (Round your answer to five decimal places.) amps Determine the charge as t → ∞.

A 200-volt electromotive force is applied to an RC-series circuit in which the resistance is 1000 ohms and the capacitance is 5 x 10-6 farad. Find the charge q(t) on the capacitor if i(0) = 0.2. q(t) = Determine the charge at t = 0.004 s. (Round your answer to five decimal places.) coulombs Determine the current at t = 0.004 s. (Round your answer to five decimal places.) amps Determine the charge as t → ∞.

Physics for Scientists and Engineers: Foundations and Connections

1st Edition

ISBN:9781133939146

Author:Katz, Debora M.

Publisher:Katz, Debora M.

Chapter29: Direct Current (dc) Circuits

Section: Chapter Questions

Problem 19PQ

See similar textbooks

Similar questions

A certain flashlight is connected to a 6.0-Vemf battery and has an internal resistance of 0.100. What power does the 0.500 M load dissipate? If the internal resistance grows to 0.400 2, what is the new current, terminal voltage, and power dissipated by a 0.500 M load resistance?
A 300-volt electromotive force is applied to an RC-series circuit in which the resistance is 500 ohms and the capacitance is 5 microfarad. What is the current (in milliamperes) at 1 millisecond if q(0)=0?
What voltage will produce 0.2 AA of current through a 4800-ΩΩ resistor? Express your answer to two significant figures and include the appropriate units. V=
For the circuit shown, with a voltage source of 36V and with all resistor values equal to 5Ω. What is the power absorbed, in Watts, in R3?
The figure shows an LED, protected by a resistor R, which is powered by a 9 Volt battery. If the power of the LED is 70 milliwatts and the voltage drop across the LED is 3.5 volts, determine the value of the resistor R in ohms that should be used in the circuit.
Consider an initially uncharged capacitor in an RC circuit. The resistance is 22,489 Ohms and the capacitance is 420 x 10^-6 F. If the source potential being used to charge the capacitor is 15 V, how long after charging begins will the power deliver to the resistor be 25% of its maximum value?
An RC circuit has a 5.5 kΩ resistor and a 8.0 µF capacitor in series, how long will ittake for the fully discharged capacitor to be charged to 95% once the switch is closed? _______How long would it if a second 8.0 µF capacitor is added in series? _______
In the circuit below, the capacitor starts out uncharged. The resistance is R = 118 Ω, capacitance is C = 0.0647 F, and the battery emf is 16.7 V. What is the charge (Q) on the capacitor at a time of t = 3.72 seconds after the switch is closed?
How much current flows thru a 6 Ω resistor in 4 minutes if it is connected to a 9V battery ?
The formula for the power output P of a battery is P=VI−RI2P=VI−RI2, where V is the electromotive force in volts, R is the resistance in ohms, and I is the current in amperes. Find the current that corresponds to a maximum value of P in a battery for which V = 12 volts and R = 0.8 ohm. Assume that a 10-ampere fuse bounds the output in the interval 0≤I≤100≤I≤15
From the given circuit, find I, the power dissipated by the resistor, and the power supplied by each source. Assume V1 = 11 V, V2 = 14 V, and V3 = -6 V.
How much current flows in a 1000 Ω resistor when there is a potential difference of 1.5 V?