A 2000-kg truck is being used to lift a 400-kgboulder B that is on a 50-kg pallet A. Knowing theacceleration of the rear-wheel-drive truck is 11 m10.6 mm/s?, determine (a) the reaction at each of thefront wheels, (b) the force between the boulderand the pallet.1.4 m > +2 m→ <1.2 m→A

Answered: Image /qna-images/answer/b0f6e2b7-2279-47d4-b7f9-d0b80d201de5.jpg

A 2000-kg truck is being used to lift a 400-kg boulder B that is on a 50-kg pallet A. Knowing the acceleration of the rear-wheel-drive truck is 1 1 m 0.6 m m/s?, determine (a) the reaction at each of the front wheels, (b) the force between the boulder and the pallet. -1.4 m 2 m→+1.2 m→ B

A 2000-kg truck is being used to lift a 400-kg boulder B that is on a 50-kg pallet A. Knowing the acceleration of the rear-wheel-drive truck is 1 1 m 0.6 m m/s?, determine (a) the reaction at each of the front wheels, (b) the force between the boulder and the pallet. -1.4 m 2 m→+1.2 m→ B

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Pin B weighs 0.1kg and is free to slide in a horizontal plane along therotating arm OC and along the circular slot DE of radius b=500mm.Neglecting friction and assuming that θ= 15 rad/s andθ=250 rad/s2 for the position θ= 20o , determine for that position(a) the radial and transverse components of the resultant forceexerted on pin B, (b) the forces P and Q exerted on pin B,respectively, by rod OC and the wall of slot DE.
Knowing that the maximum friction force exerted by the bottle on the cork is 60 lb, determine (a) the force P that must be applied to the corkscrew to open the bottle, (b) the maximum force exerted by the base of the corkscrew on the top of the bottle.
Knowing that the coefficient of static friction between the tires and the road is 0.80 for the car as shown in figure 2. At this car, suddenly brakes are applied when it was moving with velocity of 360 inch/sec and it skidded to rest in 240 inch. Determine the magnitude of the normal reaction and of the friction force in the terms of W(weight) at each wheel as the car skidded to rest. { Use m=w/g, for the mass of the car if required, where g=386.09inch/s2.}
Knowing that the coefficient of static friction between the tires and the road is 0.8 for the automobile (m=1050 kg) shown, determine 1- normal reaction at front wheels (N), the car is assumed front wheel drive. 2- normal reaction at rear wheels (N), the car is assumed front wheel drive. 3- maximum acceleration (m/s2), the car is assumed front wheel drive.
Knowing that the coefficient of static friction between the tires and the road is 0.8 for the automobile (m=1050 kg) shown, determine 1-normal reaction at front wheel (N), the car is assumed rear wheel drive. 2- normal reaction at rear wheel (N), the car is assumed rear wheel drive. 3- maximum acceleration (m/s2), the car is assumed rear wheel drive.
The uniform bar is at rest on a smooth half-sphere with radius R = b / 2. In A there is a ball joint and the bar rests at B against the vertical wall without friction. If the length of the bar AB is 4 m, and its weight is W = 200 N, at the midpoint of the bar. Take b = 1.6 m and d = 2.8 m, determine in Newtons: a) The magnitude of the normal force FN of the hemisphere on the bar. b) The magnitude of the normal force FB of the wall on the bar. c) The force AX of the patella on the bar in the X-axis. d) The force AY of the patella on the bar in the Y-axis. e) The force AZ of the patella on the bar in the Z-axis.
An 8400-kg truck is traveling on a level horizontal curve, resulting in an effective lateral force H (applied at the center of gravity G of the truck).Treating the truck as a rigid system with the center of gravity shown, andknowing that the distance between the outer edges of the tires is 1.8 m,determine (a) the maximum force H before tipping of the truck occurs,(b) the minimum coefficient of static friction between the tires and roadwaysuch that slipping does not occur before tipping.
A block with weight W is pulled up a plane forming an angle a with the horizontal by a force P directed along the plane. μ If is the coefficient of friction between the block and the plane, derive an expression for the mechanical efficiency of the system. Show that the mechanical efficiency cannot exceed 1/2 if the block is to remain in place when the force P is removed.
A tractor-trailer rig with a 2000-kg tractor, a 4500-kg trailer, and a 3600-kg trailer is traveling on a level road at 90 km/h. The brakes on the rear trailer fail, and the antiskid system of the tractor and front trailer provide the largest possible force that will not cause the wheels to slide. Knowing that the coefficient of static friction is 0.75, determine (a) the shortest time for the rig to a come to a stop, (b) the force in the coupling between the two trailers during that time. Assume that the force exerted by the coupling on each of the two trailers is horizontal.
Knowing that the coefficient of static friction between the tires and the road is 0.80 for the car as shown in figure 2. At this car, suddenly brakes are applied when it was moving with velocity of 360 inch/sec and it skidded to rest in 240 inch. The mass of the car is 300 pounds. Determine the magnitude of the normal reaction and of the friction force at each wheel as the car skidded to rest.
A rope having a weight per unit length of 0.4 lb/ft is wound 2 1/2 Times around a horizontal rod. Knowing that the coefficient of static friction between the rope and the rod is 0.30, determine the minimum length x of rope that should be left hanging if a 100-lb load is to be supported.
Using two ropes and a roller chute, two workers are unloading a 200-lb cast-iron counterweight from a truck. Knowing that at the instant shown the counterweight is kept from moving and that the positions of points A, B, and C are, respectively, A(0, –20 in., 40 in.), B(–40 in., 50 in., 0), and C(45 in., 40 in., 0), and assuming that no friction exists between the counterweight and the chute, determine the tension in each rope. (Hint: Because there is no friction, the force exerted by the chute on the counterweight must be perpendicular to the chute.)