A 21 mm diameter glass marble with a mass of 25 g rollswithout slipping down a track toward a vertical loop ofradius R=15 cm, as shown in the figure. Approximate theminimum translational speed vmin the marble must havein order to complete the loop without falling off the trackwhen it is a height H=25 cm above the bottom of theloop.HRFigure is not to scale.

therefore the minimum velocity required to complete one loop is 3.83 m/s

Answered: A 21 mm diameter glass marble with a…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Please answer this NEATLY, COMPLETELY, and CORRECTLY for an UPVOTE. The wooden block (mass m = 0.5358 kg) is released from rest at A by a compressed spring (compressed length 0.6 m, undeformed length 1 m, spring constant k = 150 N/m). The block is allowed to slide through the rough horizontal surface (A to B), then along the smooth circular ramp (B to C, central angle θ = 47.2°, until the block is released after point C. Calculate the speed of the block at points B and C. Also, what is the magnitude of the normal force exerted to the block just before the block leaves the ramp? Neglect the geometry of the block. NOTE: Use Work-Energy Method to solve for the speeds; use Force-Mass-Acceleration (FMA) Method to compute for the normal force.
A heavy cabinet with a mass of 135kg is transported on the truck platform. Assume that the friction between the cabinet and the platform is so great that the cabinet cannot slip, but can instead tip over. The dimensions shown in the cabinet figure are hG = 1.8m, xG = 1.0m and b = 3.4m. How high can the maximum acceleration of the truck to the right be without the cabinet tipping over? What is the angular acceleration of the cabinet in the situation under consideration
A barrel of mass 200 kg and radius 0.50 m rolls down a 40° ramp without slipping. What is the value of the friction force acting at the point of contact between the barrel and the ramp? Treat the barrel as a cylinder of uniform density.
Mason is is trying to keep a door open using a door stopper. That door is solid, and it has a mass of 18.3kg. The door closer is connected 26.2cm away from the hinge, and pulls with a force of 123N. The door stopper provides a static friction force of 13.2N, and a kinetic friction force off 11.8N. Find the angular acceleration (as a vector) of the door.
The propeller on Don Karnage's airplane can be modeled as three identical thin rods of uniform density extending radially from the rotational axis of the propeller. To take off, the propeller must accelerate from rest to 633 rpm in 4 s. If the length and mass of each rod are 0.872 m and 3.11 kg, what must be the magnitude of torque in N*m) necessary to accelerate the propeller? Explain how you solved the problem involving something undergoing angular acceleration Be sure to state what your known and unknown quantities are, what concepts were applied, and what equations were used!
A 0.95 kg block connected to light spring with force constant 150 N/m is free to oscillate on a frictionless, horizontal surface. The block is released from rest when the spring is stretched 15.0 cm. What is the speed of the block midway of the stretched position?
The figure shows a junction of mass m = 10kg sliding on a rod in a vertical plane. Positioned 1 simpai is stationary and horizontal spring and tensioned Fp = 300N. If the spring constant is k = 1kN/m and the average frictional force between the rod and the junction is F = 30N. Calculate the speed at position 2. (Ans: 3.47m/s)
Specifically a dynamics problem: A sphere is fired downward into a medium with an initial speed of 27 m/s. If it experiences a deceleration of a = -6t m/s2, determine the distance traveled before it stops.
Asubject of mass 65 kg has her gait analyzed. Suppose that the x componentof the force measured by a force plate takes the shape shown in Fig. (a) If the forward velocity of the walker is 2 m/s at heel strike, what is it0.4 s after heel strike?(b) Estimate the corresponding change in height for the subject’s center ofgravity (i.e., from heel strike to 0.4 s later).
a=22mist 16w/ Figure Q) “The mass of ahuckey puck 0.80Kg slides on horizontal, frictionless surface of an ice rink. If two hockey sticks srike the puck simulaneously, exerting the acceleration of the puck shown n figure 2. Determine both the magnitude and the direction of the puck’s forces?
The double slide mechanism mentioned above moves in a horizontal plane. Limb number 4 it slides downward at a constant speed of 10 m / s. For this given kinematic case, link 2 Find the strength and direction of the required force F on it. (Of limbs 2 and 4 small enough to be negligible in size)
The disk of 5 kg mass attached to a springshown in the figure is moving on a vertical plane.At a particular instant its total mechanical energyis 108 Joules, its speed is 3 m/sec, its angularspeed is 1 Rad/sec, elongation in the spring is 0.8m, and the spring constant is 80 N/m. The disk is1.2 m above the reference line shown. Determine(a) the radius of the disk, (b) angular acceleration,and (c) horizontal and vertical components ofacceleration of the disk.

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS