A 220V(rms), 50HZ sinusoidal source is connected to the primary side of an ideal transformer with 100 turns on the primary side and 300 turns on the secondary side. Primary line resistance is 22 and inductance is 10mH. Secondary line resistance is 92 and inductance is 100mH. There is a 1002 resistive load connected on the secondary side. Draw a well-labeled circuit diagram and determine: (i) Currents on both sides (ii) Load Voltage (iii) Complex power supplied by the source

A 220V(rms), 50HZ sinusoidal source is connected to the primary side of an ideal transformer with 100 turns on the primary side and 300 turns on the secondary side. Primary line resistance is 22 and inductance is 10mH. Secondary line resistance is 92 and inductance is 100mH. There is a 1002 resistive load connected on the secondary side. Draw a well-labeled circuit diagram and determine: (i) Currents on both sides (ii) Load Voltage (iii) Complex power supplied by the source

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter3: Power Transformers

Section: Chapter Questions

Problem 3.28MCQ

See similar textbooks

Similar questions

Consider an ideal transformer with N1=3000andN2=1000 turns. Let winding 1 be connected to a source whose voltage is e1(t)=100(1| t |)volts for 1t1ande1(t)=0 for | t |1 second. A2- farad capacitor is connected across winding 2. Sketch e1(t),e2(t),i1(t),andi2(t) versus time t.
An ideal transformer has no real or reactive power loss. (a) True (b) False
Consider a source of voltage v(t)=102sin(2t)V, with an internal resistance of 1800. A transformer that can be considered as ideal is used to couple a 50 resistive load to the source. (a) Determine the transformer primary-to-secondary turns ratio required to ensure maxi mum power transfer by matching the load and source resistances. (b) Find the average power delivered to the load, assenting maximum power transfer.
Consider Figure 3.25 of the text for a transformer with off-nominal turns ratio. (i) The per-unit equivalent circuit shown in part (c) contains an ideal transformer which cannot be accommodated by some computer programs. (a) True (b) False (ii) In the - circuit representation for real c in part (d), the admittance parameters Y11 and Y12 would be unequal. (a) True (b) False (iii) For complex c, can the admittance parameters be synthesized with a passive RLC circuit? (a) Yes (b) No
A single-phase, 120V(rms),60Hz source supplies power to a series R-L circuit consisting of R=10 and L=40mH. (a) Determine the power factor of the circuit and state whether it is lagging or leading. (b) Determine the real and reactive power absorbed by the load. (c) Calculate the peak magnetic energy Wint stored in the inductor by using the expression Wint=L(Irms)2 and check whether the reactive power Q=Wint is satisfied. (Note: The instantaneous magnetic energy storage fluctuates between zero and the peak energy. This energy must be sent twice each cycle to the load from the source by means of reactive power flows.)
The transformer of Problem 3.16 is supplying a rated load of 50 kVA at a rated secondary voltage of 240 V and at 0.8 posr factor lagging. Neglect the transformer exciting current. (a) Determine the input terminal voltage of the transformer on the high-voltage side. (b) Sketch the corresponding phasor diagram. (c) If the transformer is used as a step-down transformer at the load end of a feeder whose impedance is 0.5+j2.0, find the voltage VS and the power factor at the sending end of the feeder.
The rms value of v(t)=Vmaxcos(t+) is given by a. Vmax b. Vmax/2 c. 2Vmax d. 2Vmax
Consider a load impedance of Z=jwL connected to a voltage and V let the current drawn be I. (a) Develop an expression for the reactive power Q in terms of ,L, and I, from complex power considerations. (b) Let the instantaneous current be i(t)=2Icos(t+). Obtain an expression for the instantaneous power p(t) into L, and then express it in terms of Q. (c) Comment on the average real power P supplied to the inductor and the instantaneous power supplied.
You are given five light bulbs designed to operate on 160 mA current at 3.0 V (rms values), arid want to connect them in parallel, through an ideal transformer, to 120 V rms AC household power. a) Draw a circuit diagram showing the AC power source (a generator symbol ), the transformer, and resistors for the light bulbs. b) Is the required transformer step-up or step-down? What turns ratio N5/N is needed? e) Calculate the ruts current through both the primary and secondary coils of the trans former, in mA.
Determine the amount of power, in watts, consumed by the transformer shown. Assume that the voltage source is ideal (Rs=50 mΩ), R1=5 Ω, and L1=250 mH. The frequency of the 120 V(rms) source is 60 Hz.
Neon signs (which often contain gases other than neon) use high voltage to excite gaseous atoms that then give off a characteristic glow. When plugged into a wall outlet (120 V AC), a typical neon sign transformer delivers 400 W AC at a voltage of 18 kV rms. The primary coil has 400 turns. 1. First, what is the number of turns in the secondary to achieve this high voltage? Give your answer to 2 significant digits. 2. Next, if the transformer is ideal, what is the rms current in the primary? Give you answer in amps with 2 significant digits. 3. Finally, what is the rms current in the secondary? Give your answer in milli-amps with 2 significant digits.
For the circuit shown in the given figure, assume that Vg˜=45 ∠0 V rms��~=45 ∠0 V rms , Rg = 9 Ω, and Ro = 5 Ω. Assume an ideal transformer. Find the equivalent resistance seen by the voltage source. The equivalent resistance is ________∠___________ Ω.