Answered: A 230-V, kVA single-phase transformer…

A 230-V, kVA single-phase transformer has an iron loss of 100 W at 40 Hz and 70 W at 30 Hz. Find the core loss at 50 Hz. a. 118.19 W b. 125.56 W c. 128.65 W d. 133.34 W

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter3: Power Transformers

Section: Chapter Questions

Problem 3.4MCQ: An ideal transformer has no real or reactive power loss. (a) True (b) False

See similar textbooks

Related questions

Q: write about: Typical Band Stop Filter Configuration 200 words do not write in handwritten and DO…

A: In this following section, 200 work description on bandpass filter configuration has been described.…

Q: Obtain the timing diagram for the Master-Slave flip flop with appropriate assumptions for the…

Q: 1. In the following circuit, what is the peak current, in amperes (A), through the secondary coil,…

A: The solution is given below

Q: Encuentre la tonrión VclH) para t> 0 del crcuito a la 125 F 18 Función U(t) Ve • C- T2u14) A 24 mm…

A: The solution is given below

Q: 5 2 10 s2 Q.16: For the circuit shown, Find: 1. Thevenin equivalent circuit w.r.t c & d? 2. ZL for…

Q: Find Thevenin's equivalent circuit for the circuit shown below 8. RL 12 100 V orbon inding No ww

A: This question belongs to circuit theory . It is based on the concept of Thevenin's theorem .…

Q: 13.13 The switch in the circuit in Fig. P13.13 has been in position a for a long time. At t = 0, it…

Q: The open-circuit characteristic of a DC generator is also called as characteristics. O internal…

A: There are two types of characteristics of DC generator: No load saturation characteristics Internal…

Q: [5] Let x[n] be discrete-time signal obtained from x (1) using sampling period T = 0.1 sec, and…

A: Given information: Sampling time T=0.1 s Expression of the signal is xn=1↑,0,-1,0

Q: a. The tachometric feedback path affects the relative damping of a system as shown in Figure2. 15…

A: The given block diagram can be reduced by considering the parallel connection and then the feedback…

Q: 5- Determine the truth table of the digital circuit shown in the figure below and explain its…

Q: 3.1) How many PIC24 Timer2 ticks are equal to 1.2 ms assuming a prescale of 8 and a Fcy of 30 MHz?…

A: “Since you have asked multiple question, we will solve the only one question for you. If you want…

Q: Study the circuit below: +12V R2 is a light-dependent-resistor (LDR). It is 5002 when exposed to…

Q: determine the current i(t) for t>0 for the following circuit

A: Circuit is given as,

Q: E6.15 A system has a characteristic equation q(s) = s6 + 9s5 + 31.25s + 61.25s %3D + 67.75s? +…

A: The solution is given below

Q: Q2.Determine the following for the fixed-bias configuration shown: a) IBQ and ICQ b) VCEQ e) VB and…

A: The required parameters can be calculated by using DC analysis of the amplifier circuit.

Q: A 100-0 resistor and a 50-0 resistor are connected in parallel and a total current of 3 A flows.…

A: The solution is given below

Q: 8.49 If I, = 4 /0° A in the circuit in Fig. P8.49, find I,. O 12/0 v O26 A 10 10 I, ww 10 I, ww 4/0…

Q: the Boolean expression for function Z. b) Using not more than 10 transistors, draw the gate-level…

Q: If a circuit is operating at a frequency of 135 rad/sec and the circuit has a capacitor with a value…

A: Given data, Angular frequency, ω=135 rad/s Capacitance, C=2 mF

Q: 0< lo|<0.47 0.47 < |0|ST Se i0.30 X(cm)=

Q: In a circle of a radius 4 feet, what central angle corresponds to an arc length of 8 feet? A. 4…

Q: 5. For the circuit shown in Figure the current through the 10 ko resistor is 20 VZ 0° 2.2 kl 5VZ 0°…

A: The solution is given below

Q: Calculate the total load and service for a 38 ft 28 ft (11.6 m 8.55 m) apartment building. Base your…

A: Given reactive power input is Q=15 kVAR. Load power factor is 0.8. cos(ϕ)=0.80 sin(ϕ)=0.6 By using…

Q: Write an Arduino code to control two LEDs using two push buttons, given the bellow setup: LED 1 is…

A: The LED pins should be used as output pins and Button pins should be used as Input pin in program.

Q: Q4/ A PCM system uses a uniform quantizer followed by a 7-bits binary encoder. The bit rate of the…

Q: 2. Find i,(t) if v,(t) = -20 sin(25t – 30°) V %3D

A: It is given that: Vst=-20sin25t-30° V

Q: Find y[n]=x[n]*h[n] for all integer values of n

Q: 3. Find Idc, Vdc and the capacitance that will force the Vr(pp) to 3mV. Draw the output waveform…

Q: For the circuit shown in Fig. 2 (i),find the maximum and minimum values of zener diode current. 5 k2…

A: Given circuit, Source voltage range, VS=80-120 V

Q: Q1: Determine X(z) for each of the following and write anddraw ROC: a) x(n) = [ 3 0 22 - 12 6 10 1 0…

A: In this question we need to find a z transform of the given signal.

Q: Q2. The DTFT of x[n] is X(ej@) = Find the following: (1-0.73 e-ja) (a) x[n] (b) DTFT of x'I-n] (c)…

A: As per our guidelines we are supposed to be answer the first three questions only. Kindly repost…

Q: Q2 A series resonant converter is shown in Fig. 2. The load parameters are R= 1.2 , Luw = = 10 N.…

Q: Which of the following is most likely to be the noise in a communication process? A viewer watches a…

A: The noise is associated with any interference in the communication channel, the noise in the channel…

Q: 7. What will happen to the resistance of a conductor if we reduce its cross- sectional area by a…

A: We need to select correct option for given statement

Q: Q2/ The information in an analog signal voltage waveform is to be transmitted over a PCM system with…

Q: 5 Derive a formula for gu, gd, and gavg for HI-skew and LO-skew k-input NAND gates with a skew…

A: Consider circuits..... This is the statement for question 6 & 7. As per guidelines we can answer…

Q: Problem 2: Write the Boolean function of OUT of the following circuits. (No need to draw) OUT R FÖUT…

A: Write the Boolean function of OUT of the following circuits.

Q: A cylindrical wire has a radius r and length I. If both r and I are doubled, what happens to the…

A: Given: A cylindrical wire has, Case 1, Radius, r1=r Length, L1=L Resistance, R1=R Case 2, when both…

Q: By using N-Mos, plot the following equation with the transistor y = AB + CBD?

Q: 32. For the circuit in Figure 5–63, draw the waveforms at the numbered points in the proper rela-…

Q: 210 1 280 0 24 N 36 n 18ng 30 mA (4 200 n 1202 180 ng (a) (b)

A: Note: We are authorized to answer three subparts at a time, since you have not mentioned which part…

Q: For a non inverting amplifier based on 741, calculate the O/P voltage, and draw both O/P voltage and…

A: The noninverting opamp is an amplifier circuit that amplifies the given input signal without…

Q: Q/ Design a multirange ammeter by using direct method to give the following ranges 10mA, 10mA, 1A,…

A: In this question we need to design a multirange ammeter.

Q: For the right shown system, draw the output signal y in x(t)- y the range [0-2] sec where x(t) = sin…

A: Multiplication:

Q: 5. Find the fundamental period of 1+sin^2 (3t/5)n. a) 10/3 b) 5 с) Зл/5 d) None of the mentioned

A: In this question we will find fundamental time period of given discrete system....

Q: PROBLEM: Represent the translational mechanical system shown in state space, where x3(t) is the…

A: It is given that:

Q: 8 Domino (footed). Note that a Domino gate must be followed by an Inverter. Therefore, the nMOS…

A: “Since you have asked multiple question, we will solve the first question for you. If you want any…

Q: 7-2 Q-4. Derive an expression of Vo for the following circuit 2R R R. www Vo 2R R V2-ww

Q: an unintentional electrically conducting connection between and ungrounded conductor of an…

A: The fault occurs due to connection between the ungrounded conductor and the metallic raceways,…

Concept explainers

Three-Phase Transformers

Three-segment transformers are a type of transformer used to transform voltages of electrical systems into three ranges. Two type transformers are shell-type transformer and core type transformer. In brief, it could be described because of the exquisite kinds of configurations.

Transformer

Ever since electricity has been created, people have started using it in its entirety. We see many types of Transformers in the neighborhoods. Some are smaller in size and some are very large. They are used according to their requirements. Many of us have seen the electrical transformer but they do not know what work they are engaged in.

Question

52. A 230-V, kVA single-phase transformer has an iron loss of 100 W at 40 Hz and 70 W at 30 Hz. Find the core loss at 50 Hz. a. 118.19 W b. 125.56 W c. 128.65 W d. 133.34 W

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

An ideal transformer has no real or reactive power loss. (a) True (b) False
For an ideal transformer, the efficiency is (a) 0 (b) 100 (c) 50
For a short-circuit test on a 2-winding transformer, with one winding shorted, can you apply the rated voltage on the other winding? (a) Yes (b) No
Rework Problem 3.14 if the transformer is delivering rated load at rated secondary voltage and at (a) unity power factor, (b) 0.8 power factor leading. Compare the results with those of Problem 3.14. -
A single-phase, 50-kVA,2400/240-V,60-Hz distribution transformer has the following parameters: Resistance of the 2400-V winding: R1=0.75 Resistance of the 240-V winding: R2=0.0075 Leakage reactance of the 2400-V winding: X1=1.0 Leakage reactance of the 240-V winding: X2=0.01 Exciting admittance on the 240-V side =0.003j0.02S (a) Draw the equivalent circuit referred to the high-voltage side of the transformer. (b) Draw the equivalent circuit referred to the low-voltage side of the transformer. Show the numerical values of impedances on the equivalent circuits.
For the transformer in Problem 3.10. The open-circuit test with 11.5 kV applied results in a power input of 65 kW and a current of 30 A. Compute the values for GcandBm in siemens referred to the high-voltage winding. Compute the efficiency of the transformer for a load of 10 MW at 0.8 p.f. lagging at rated voltage.
(a) An ideal single-phase two-winding transformer with turns ratio at=N1/N2 is connected with a series impedance Z2 across winding 2. If one wants to replace Z2, with a series impedance Z1 across winding 1 and keep the terminal behavior of the two circuits to be identical, find Z1 in terms of Z2. (b) Would the above result be true if instead of a series impedance there is a shunt impedance? (c) Can one refer a ladder network on the secondary (2) side to the primary (1) side simply by multiplying every impedance byat2 ?
An ideal transformer with N1=1000andN2=250 is connected with an impedance Z22 across winding 2. If V1=10000VandI1=530 A, determine V2,I2,Z2, and the impedance Z2, which is the value of Z2 referred to the primary side of the transformer.
Reconsider Problem 3.64 with the change that now Tb includes both a transformer of the same turns ratio as Ta and a regulating transformer with a 4 phase shift. On the base of Ta, the impedance of the two comp onents of Tb is jO.1 per unit. Determine the complex power in per unit transmitted to the load through each transformer. Comment on how the transformers share the real and reactive pors.
The ratings of a three-phase three-winding transformer are Primary(1): Y connected 66kV,15MVA Secondary (2): Y connected, 13.2kV,10MVA Tertiary (3): A connected, 2.3kV,5MVA Neglecting winding resistances and exciting current, the per-unit leakage reactances are X12=0.08 on a 15-MVA,66-kV base X13=0.10 on a 15-MVA,66-kV base X23=0.09 on a 10-MVA,13.2-kV base (a) Determine the per-unit reactances X1,X2,X3 of the equivalent circuit on a 15-MVA,66-kV base at the primary terminals. (b) Purely resistive loads of 7.5 MW at 13.2 kV and 5 MW at 2.3kV are connected to the secondary and tertiary sides of the transformer, respectively. Draw the per- unit impedance diagram, showing the per-unit impedances on a 15-MVA,66-kV base at the primary terminals.
For an ideal 2-winding transformer, the ampere-turns of the primary winding, N1I1 is equal to the ampere-turns of the secondary winding, N2I2 (a) True (b) False
A single-phase 50-kVA,2400/240-volt,60-Hz distribution transformer is used as a step-down transformer at the load end of a 2400-volt feeder whose series impedance is (1.0+j2.0) ohm. The equivalent series impedance of the transformer is (1.0+j2.5) ohms referred to the high-voltage (primary) side. The transformer is delivering rated load at a 0.8 power factor lagging and at a rated secondary voltage. Neglecting the transformer exciting current, determine (a) the voltage at the transformer primary terminals, (b) the voltage at the sending end of the feeder, and (c) the real and reactive power delivered to the sending end of the feeder.