A 240 rms 60 Hz source supplies a parallel combination of a 4.5-kW heater and a 27-kVA inductor motor whose power factor is 0.82. Determine the kVA rating of the capacitor required to adjust the system power factor to 0.9 lagging and the value of the capacitor required?

A 240 rms 60 Hz source supplies a parallel combination of a 4.5-kW heater and a 27-kVA inductor motor whose power factor is 0.82. Determine the kVA rating of the capacitor required to adjust the system power factor to 0.9 lagging and the value of the capacitor required?

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.21P: An industrial plant consisting primarily of induction motor loads absorbs 500 kW at 0.6 power factor...

See similar textbooks

Related questions

Q: An input signal x(t)=e-3t u(t) is applied to an LTI system with impulse response h(t) = 38(t) + e -2…

Q: Q4: A. Design a class AB amplifier stage to(40) load speaker from +25V supplies; calculate the input…

A: Let's assume a class AB amplifier stage with complementary NPN and PNP transistors and a quiescent…

Q: (ep00) After a completely inelastic collision, two objects of the same mass and same initial speed…

Q: A 12 volt battery has a rating of 6 Ah. It is used to send current through a material that has a…

A: Supply voltage, Vs=12 V. Charge capacity, Q=6 Ah. Resistivity, ρ=100 Ω-cm. Radius, r=1 cm. Length,…

Q: Explore the numerous access control classes. Discuss the many controls that may be added to any…

Q: The current, i, through a capacitor depends on time, t, and is given by i= c() where V is the…

A: In this question We need to determine the voltage across the terminal capacitor. Given current in…

Q: Determine the discrete-time Fourier transform of the signal x[n] = (0.5)¹−¹u[n − 1]. O a. X(w) = O…

A: here we have to find the DTFT of the given signal

Q: Homework D2.2. A charge of -0.3 μC second charge of 0.5 μC is at (b) P(15, 20, 50) cm. is located at…

Q: Q1) Conduct an evaluation on the practical applications of the concepts of electromagnetism and…

A: Given: Discuss about the principles of electromagnetism used in the simulation.

Q: In the circuit shown, the switch is open, and the capacitors are uncharged. At t=0, the switch S is…

Q: An electric plant that produces 11 x 10⁹ kWh/year has an annual investment expenditure of $44.5 x…

A: An electric plant that produces 11 x 109 kWh/year has an annual investment expenditure of $44.5 x…

Q: Problem 4. What is the impulse response of the ideal bandpass filter drawn below with amplitude 1…

A: In the given question we need to find the impulse response of the given ideal bandpass filter

Q: AM transmitter has a 1KW carrier power and is modulated by a sinusoidal tone. If you have 0.7…

A: Given , Pc = 1 kW and modulation index m = 0.7,

Q: Determine the breakdown slip and the maximum developed torque by a three-phase, star- connected,…

Q: Explain the concept of the continuous-time Fourier transform and its significance in analyzing the…

A: The continuous-time Fourier transform (CTFT) is a mathematical tool used to analyze the frequency…

Q: Find the difference equation of the system. Find the transfer function H(z) of the system

A: Here we have to find the difference equation and transfer function.

Q: Please correct and clean solution and both part are solve

A: Given Data VBE= 0.7Vbeta=100VA=50 V

Q: 1. Consider the DC linear machine system shown in the figure below. In that sense, answer ask. + Vi…

A: Given: In this question, the given details are, Consider the DC linear machine system shown in the…

Q: Question 18 Select the correct intersection of the asymptotes and the real axis: O-4/3 0 0 O-2…

A: In this questions we need to choose a correct option

Q: Design an FIR linear phase, digital filter approximating the ideal frequency response: 1, -& Ha(w) =…

A: We need To find the following Coefficient of 25-tap FIR filter using, i) Rectangular window,…

Q: 2) Adve the following a separate parts: 2 R that (a) For the circuit shown, find the value of…

A: Given data Io=10 μA β=100 VA=100 V To find out (a) We have to determine the value of Ro. (b) We have…

Q: 5. Using nodal analysis, determine Vo in the circuit in Figure 5. 40 V 2002 102 www 2002 41 10:2…

Q: 2. Plastic kayaks are manufactured using a process called rotomolding. Molten plastic is injected…

Q: Ck 1, k = 1,5 0, O a. 2 cos (2) O b. O c. O d. cos (27) cos (2T) 2 cos (2T) k = 0, 2, 3, 4 = {...,…

A: In this question we need to find the periodic signal f[n] given the following DTFS coefficients for…

Q: Find Vo for the circuit in Figure using: 1. Mesh analysis 2. Nodal analysis 3. Thevenin's theorem

Q: 2. For the network of Figure 2 with the measurement Vs = 1.7 V, determine: a. Ip b. VGS c. lpss d.…

Q: -1 -5 A = 1 -2 0 0 C = [1 0 1] 1 −1 [0 B = 1 D = [0]

A: H(s) = C(sI - A)^(-1)B + D where s is the Laplace transform variable, I is the identity matrix,…

Q: (b) The circuit in Figure Q5 (b) shows a different configuration of amplifier. (i) What is the name…

A: The type of amplifier configuration needs to be identified from the given circuit. The input…

Q: Problem 5. Based on the pole/zero placement, Is the following filter a LPF, HPF, BPF, or Notch…

Q: iv) Find the value of i4 using the analytical method for v = V₁ + v₁ = 11 V. v) Now, find the exact…

A: Given: The circuit below contains a nonlinear element N whose v-i relationship is given by the…

Q: Vref (s) КА 1+0.05s Amplifier VR(S) 1+0.58 Exciter Vp(s)[ 0.8 1+8 Generator Vt(s)

A: The figure represents an Automatic Voltage Regulation (AVR) system consisting of three cascaded…

Q: In the circuit in the diagram below the meter M which has the internal resistance R goes to exactly…

A: The given circuit is shown below. In the circuit in the diagram below the meter M has an internal…

Q: a Af V8 = 5V 10032 A A 20032 R₂ 20 300-2 R;

Q: A shunt motor is rotating at 1500 rpm and is powered by a 120V voltage source. The current line…

A: In this question we need to find the following a) the armature current, b) the back emf (E), c) the…

Q: (3) 4. a. For the cicuit to the the right show that:. H(@) = (-C,R₂) jo (1+ joRC) (1+jøR₂C₂) R₁ G₁…

A: it is asked to prove the given transfer function

Q: Figure 1.28 shows a circuit with four elements, P₁ = 60 W absorbed, p3 = -145 W absorbed, and P4= 75…

A: It is given that: P1=60 W absorbedP3=-145 W absorbedP4=75 W absorbed

Q: Exercise 10.21 e a) Given V₁ = 1V e |V₂| = 1V, find the effective (RMS) value of V. b) If the RMS…

A: In this question we need to find the RMS value of voltage V

Q: V DC separately excited motor has ure resistance 2 ohms and voltage constant V /rad/s. The field…

A: V = 100 V Ra = 2 ohm Kb= 0.6 V/rad/s T= 20 Nm Kt = 50 Nm/s

Q: What is the difference between DC and AC analysis of an amplifier? State few characteristics of each…

A: What is the difference between DC and AC analysis of an amplifier? State few characteristics of each…

Q: B. Assuming a 1 ounce copper PCB, what is the resistance per centimeter of traces with the following…

A: Assuming a 1 ounce copper PCB The objective is the resistance per centimeter of traces with 1 mil,…

Q: True or False: A diode can be used as a voltage source.

A: A diode is a two stage terminal passive device which consumes power. An active device is the device…

Q: 4. A 30 μF capacitor is connected in series with a resistance 33 0 to a 100 V, 100 Hz supply.…

A: The value of cpacitance, C=30 μF The value of the resistor, R=33 Ω The source voltage, Vs=100 V The…

Q: The Fourier transform of a continuous-time signal ä(t) is denoted by X(N). What is the Fourier…

A: It is asked to find the Fourier transform for given signal

Q: R₂= 2300 2 Identify, write out the general formula for circut gain Determine output voltage for the…

A: Operational amplifier with negative feedback.

Q: A SSB signal is generated by modulating an 800 kHz carrier by signal m (t) = cos (2000nt) +2Sin…

A: According to the question, a SSB signal is generated by modulating an 800 kHz carrier by signal m…

Q: 3. A point charge, Q₁ = 20uC, is located at P₁(3,2,1) in free space, while Q₂ = -5uC is at…

A: point charges Q1 = 20 μC at P1 (3,2,1) Q2 = -5 μC at P2 (1,2,5)

Q: The current flowing through a 22.6H inductor is given by iL (t) Find the voltage across the inductor…

A: In a circuit, Inductance, L=22.6 mH. Current through inductor, iLt=575e-20t mA. To calculate the…

Q: (b) The z transfer function of a digital control system is given by 1 (z − 2k) (z − k² – 0.64) G(z)…

Q: Determine the total capacitance, in nF, of a parallel-plate capacitor having three dielectrics in…

Q: Calculate 11, 12, 13, 14 and 15 3+j5 Q 100/0° V 1₁ 40.0 12 3-16 Q 4+j6 Q 13 30 14 110 ³0 30 15 5+j8…

Concept explainers

Synchronous Motor

The synchronous motor is an AC electric type motor where at a steady-state the shaft rotation is synchronized with the supply current variable-frequency. To an integral number of AC cycles, the rotation period is exactly equal. The stator of the motor in the synchronous motor contains multi-phase AC electromagnets due to which a magnetic field is created that rotates in time with the oscillation of the line current. The rotor contains a permanent magnet and the rotor rotates in synchronization with the stator field at the same rate and provides the second synchronized magnetic field which is rotating in nature as a result. When the synchronous motor is supplied with independently excited multi-phase AC electromagnets on both the rotor and the stator, it is termed as a doubly-fed machine. The most widely used AC-type motors are the synchronous AC motor and the induction AC motors.

Question

A 240 rms 60 Hz source supplies a parallel combination of a 4.5-kW heater and a 27-kVA inductor motor whose power factor is 0.82.

Determine the kVA rating of the capacitor required to adjust the system power factor to 0.9 lagging and the value of the capacitor required?

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1: Introduction

VIEW

Step 2: Calculation

VIEW

Step 3: Finding KVAR rating of capacitor

VIEW

Step 4: Finding value of capacitor

VIEW

Solution

VIEW

Step by step

Solved in 5 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A 240 kVA synchronous motor of rated apparent power consumes 95 kW of active power of the power grid. And it is possible to adjust it so that by working with this same active power, it compensates the power factor by providing reactive power (i.e., appearing with a capacitive component). How can you get this? What is the maximum reactive power that it can provide?
One phase of a 3-phase alternator consist of 12 coils in series. Each coil has an rms voltage of 10Vinduced in it and the coils are arranged in slots so that there is a successive phase displacement of10 electrical degrees between the emf in each coil an the next. Find by calculation the rms value ofthe total phase voltage developed by the winding. If the alternator has six pole and is driven at 100rpm.
One phase of a three-phase alternator consists of twelve coils in series. Each coilhas an rms voltage of 15 V induced in it and the coils are arranged in slots so thatthere is successive phase displacement of 20 electrical degrees between the emfin each coil and the next. Find the rms value of the total phase voltage developedby winding. If the alternator has six poles and is driven at 200 rpm, calculate thefrequency of the emf generated.
A 400-V, 3-phase induction motor load takes 900 kVA at a power factor of 0.707. Calculate the KVA rating of the capacitor bank to raise the resultant power factor of the installation of 0.866 lagging. Find also the resultant power factor when the capacitors are in circuit and the motor load has fallen to 300 kVA at 0.5 power factor.
Q6: An AC source operating at 60 Hz with a maximum voltage of 170 V is fed to a series combination of1.2kΩ resistor and 2.5μF capacitor connected in a timer circuit. How can you evaluate the maximumcurrent in the circuit? Can you estimate the rms value potential difference across each circuit element?Compare the power factor of this timer circuit with a circuit contain only ohmic resistance. Justify youranswer?
A 3 phase 10 pole 600 rpm delta connected alternator has 12 slots/pole with 8 conductors per slot. The windings are short chorded by 2 slots. The flux per pole contains a fundamental of 100 mwb, the third harmonic having an amplitude of 33% and fifth harmonic of 20% of the fundamental. Determine the rms value of the phase ,line voltages and Circulating Current Please answer in typing format please
A 1200 kVA, 6600 volt, 3-phase, Y-connected alternator has an effective resistance of 0.40 ohm and a reactance of 6 ohms per phase. It delivers full load current of 0.80 lagging power factor at rated voltage. What will be the terminal voltage for the same excitation and load current if the power factor is 0.80 leading? a. 4,560 V b. 9.878 V c. 7.898 V d. 4,250 V Choose the letter of the correct answer. Show your solution.
A single-phase motor draws 180 W at a power factor of 0.8 lagging when connected across a 240 Vrms, 60-Hz source. A capacitor is connected in parallel with the load to produce a unity power factor. Determine the required capacitance. The required capacitance = ____ μF.
A 40 kW induction motor, with a lagging power factor of 0.76, is supplied by a 120 V rms 60 Hz sinusoidal voltage source. Find the capacitance needed in parallel with the motor to raise the power factor to: (a) 0.9 lagging, and (b) 1.0.
A 400hp induction motor and a 400hp synchronous motor both are operating at 90% efficiency. The induction motor power factor is 0.8 lag. The synchronous motor power factor is unity. How many amperes of incandescent lighting may be added to the plant at the same KVA load if the synchronous motor is operated at a leading power factor 0.8? The supply is 600V, 3-phase.
A 50kVA, 550V single phase alternator draws a field current 10A at rated load. With the same field current, the open circuit emf and shirt circuit current are 300V and 150A. The ohmic resistance of the armature between terminals is 0.18Ω. The ratio of effective to ohmic resistance may be taken as 1.5. Determine the terminal voltage at 0.8 pf factor lagging. Use two decimal places.
An impedance coil having a resistance of 15 ohms and an inductance of 0.08 henryis connected in series with a variable capacitor. If a 117 volt 60 cps source isconnected to the circuit, what will be the capacitance of the capacitor and the current(a) when the circuit has a power factor of 0.866 leading and (b) when the voltagedrop across the coil is equal to the voltage drop across the capacitor?