A 25-mm-diameter steel [E = 202 GPa; a = 11.9x106/°C] bolt is used to connect two rigid parts of an assembly. The bolt length is a = 175 mm. Determine the minimum clamping force that must be provided by the bolt when T₁ = 19°C so that the clamping force it exerts when T₂- 56°C is at least 2.2 kN. a Answer: F₁= i KN

A 25-mm-diameter steel [E = 202 GPa; a = 11.9x106/°C] bolt is used to connect two rigid parts of an assembly. The bolt length is a = 175 mm. Determine the minimum clamping force that must be provided by the bolt when T₁ = 19°C so that the clamping force it exerts when T₂- 56°C is at least 2.2 kN. a Answer: F₁= i KN

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Determine the horizontal displacement of joint A. Each bar is made of A992 steel and has a cross-sectional area of 1.5 in2.
Determine the displacement at D of the steel beam as shown. Take E = 29(103) ksi, I = 800 in4.
The two vertical rods attached to the rigid bar are identical except for length. Before the weight P was attached, the bar was horizontal. Neglect the weight of the bar. Calculate the axial force in rod A in kips (4 decimal), if P=53 kips.
Determine thy vertical displacement (mm) of joint B. Support A is roller and support D is hinge. A=2500 mm2 E=200 GPa
Solve the following problems completely and neatly. Use 3 decimal places in all your computations except for strain and rho(5 decimal places). Input your answer in the text box provided in each number. Calculate the maximum positive moment in the beam in kN.m.0 Calculate the effective depth of the section in PART A in mm.0
Calculate for the axial force in kN at member GC of the frame shown in figure 2 using cantilever method. Enter absolute value and use 2 decimal places in your solution. a = 33.8 kN b = 27.2 kN C= 4.8m
A wide flange section has the following properties: bf = 240 mm tf = 8 mm d = 300 mm tw = 8 mm Calculate the radius of gyration in mm about the x-axis.
A tripod shown supports a load of P = 1000 N at point A. Take note that ball and socket joints are used to mount the triopd at points B, D, and C. Consider the following:L1 = 2L2 = 4L3 = 5θ = 45°α = 30 Point C coordinates: (2, -2, 3) *Do not use Vectors in solving Determine the following: Force of AB = __NForce of AC = __NForce of AD = __N
Solve a part only in 20 min and take a thumb up plz
Solve the following problems completely and neatly. Use 3 decimal places in all your computations except for strain and rho(5 decimal places). Input your answer in the text box provided in each number. Calculate the ultimate moment capacity of the section in PART A in kN.m
A rigid bar AB if of a length B = 66 in. is. hinged to a support at A and supported by two vertical wires attached at points C and D (see figure). Both wires have the same cross-sectional area (A= 0.0272 in2) and are made of the same material (modulus E = 30 X 106 psi). The wire at C has a length h = 18 in. and the wire at D has a length twice that amount. The horizontal distances are c = 20 in. and d = 50 in. (a) Determine the tensile stresses ac find aD in the wires due to the load P = 340 lb acting at end B of the bar. (b) Find the downward displacement 8B at end B of the bar.
Determine the displacement of point B of the steel beam as shown. Take E = 200 GPa, I = 500(106) mm4.