A 3-phase, 415 V, 50 Hz induction motor draws 5 times the rated current at rated voltage at starting. It is required to bring down the starting current from the supply to 2 times of the rated current using a 3-phase autotransformer. If the magnetizing impedance of the induction motor and no load current of the autotransformer is neglected, then the transformation ratio of the autotransformer is given by (round off to two decimal places).

A 3-phase, 415 V, 50 Hz induction motor draws 5 times the rated current at rated voltage at starting. It is required to bring down the starting current from the supply to 2 times of the rated current using a 3-phase autotransformer. If the magnetizing impedance of the induction motor and no load current of the autotransformer is neglected, then the transformation ratio of the autotransformer is given by (round off to two decimal places).

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A three-phase 60 Hz induction motor connected to a three-phase bus at rated voltage isoperating at a low slip condition (i.e s < 20%) resulting in a steady state speed of 1090 rpm.(a) How many poles does the motor have?(b) What is the percentage slip at the operating speed?(c) What is the corresponding frequency, (fr) of the currents and voltages induced in therotor winding?
18. A single-phase, 120 V, 60 Hz, four-pole, split-phase induction motor has the following standstill impedances:Main winding: Zm =5+j6.25Auxiliary winding: Za =8+j6a) Determine the value of capacitance to be added in series with the auxiliary winding to obtain maximum starting torque.b) Compare the starting torques and starting current with and without the added capacitance in the auxiliary winding circuit when operated from a 120V, 60Hz supply.
A three-phase induction motor, operating at rated voltage and frequency, has a startingtorque of 1.35 times and a maximum torque of 2.2 times, both with respect to its rated-loadtorque. Ignoring the effects of the stator resistance and rotational losses and assumingconstant rotor resistance, determine the slip rated load, and the rotor current at starting (as a percentage of the rotor current at rated load). The slip at maximum torque is 0.343 if that helps.
Design and develop equivalent circuit model of a single phase Induction motor with th consideration of core losses present with the parameter consideration of stator resistance R1 and reactance X1 and two rotor parameters which includes r2,x2 and magnetising reactance xm. (Illustration is required) Draw by hand please
A three phase, 4 pole, 3300 V, 50 Hz, star connected Induction motor, has identical primary and referred secondary impedance of value 3+j9 Ohm per phase. Using the approximate circuit, calculate: A. The full load torque at rated slip of 5%. B. The maximum torque at normal voltage and frequency.
The full load slip of a 4-pole, 60Hz, 440V (line-to-line) three phase induction motor is 0.05. (i). What is the speed of the rotating stating? What is the frequency (in Hz) of the rotor current? (ii). When the output power of the motor is 90 hp at a speed of 1732 rmp, rotational losses (which include frictional and core losses) are 10,100W, while copper losses for both the rotor and stator total 3700W. Determine the motor efficiency and line current, assuming the motor has a 0.8pf lagging under the conditions.
A four-pole, single-phase, 120 V, 60 Hz induction motor gave the following standstill impedances when tested at rated frequency:Main winding : Zm =1.5+j4 ohmsAuxiliary winding : Za =3+j6 ohmsa) Determine the value of external resistance to be inserted in series with the auxiliary winding to obtain maximum starting torque as a resistor split-phase motor.b) Determine the value of the capacitor to be inserted in series with the auxiliary winding to obtain maximum starting torque as a capacitor-start motor.c) Determine the value of the capacitor to be inserted in series with the auxiliary winding to obtain maximum starting torque per ampere of the starting current as a capacitor-start motor.d) Compare the starting torques and starting currents in parts (a), (b), and (c) expressed as per unit of the starting torque without any external element in the auxiliary circuit, when operated at 120V, 60Hz.
Q2. For a 10 kW, 380V, three-phase, four-pole, 1200 r/min, delta-connected induction motor. Adopt a specific magnetic loading of 0.4712 Wb/m2 and a specific electric loading of 23000 ampere-conductors per metre. The motor has a full-load efficiency of 85% and a full-load power factor of 0.8. A square pole design may be assumed and the stator leakage impedance voltage drop may be ignored. Assume also that the winding is full-pitched and uniformly wound. To calculate the following design parameters (a) The approximate outer diameter and length of the rotor core (b) the air gap length of the motor (c) the turns per phase (d) the number of conductors per slot, if 3 slots per pole per phase are chosen
A three-phase, 460-V, 60-Hz, four-pole Y-connected induction motor has the following equivalent circuit parameters: Rs = 0.42Ω, Rrʹ = 0.23Ω, Xs = Xrʹ = 0.82Ω, and Xm = 22Ω. The no-load loss 60W, may be assumed constant. The rotor speed is 1750 rpm. The rotational losses at this speed is 500W. Use the approximate equivalent circuit in figure below, to determine (a) the synchronous speed Ns; (b) the slip s; (c) the input current Ii; (d) the input power Pi; (e) the input PF of the supply, PFs; (f) the gap power Pg; (g) the rotor copper loss Pru; (h) the stator copper loss Psu; (i) the developed torque Td; (j) the efficiency; (k) the starting current Irs and starting torque Ts; (l) the slip for maximum torque sm; (m) the maximum developed torque in motoring, Tmm
A 3-phase, 440-V, delta-connected, 4-pole 50-Hz induction motor runs at a speed of 1447 rpm when operating at its rated load. The equivalent circuit has the following per-phase :parametersr1=0.2 Ω, x1=x2'=2 Ω , r2'=0.4 Ω, rc=200 Ω , xɸ = 40 Ω Using the approximate circuit, determine, for rated load, the values of line current and power factor, torque, output power and efficiency. The mechanical loss is 1000 watts.
A 3300-V, 50-Hz, 3-phase, 4-pole, star-connected induction motor has identical primary and referred secondary impedances of value 3 + j9 ohm per phase. The turns-ratio per phase is 3/I (stator/rotor), and the rotor winding is connected in delta and brought out to slip rings. Calculate: the full-load torque at rated slip of 5%; the maximum torque at normal voltage and frequency; the supply voltage reduction which can be withstood without the motor stalling; the maximum torque if the supply voltage and frequency both fall to half normal value; the increase in rotor-circuit resistance which, at normal voltage and frequency, will permit maximum torque to be developed at starting. Express this: as a fraction of normal R2and as (3) ohmic values to be placed in series with each of the slip-ring terminals and star connected.
A 80 kW, 480-V, 60-Hz, six pole induction motor has a slip of 5 percent when operating at fullload conditions. At full-load conditions, the friction and windage losses are 300 W, and the core losses are 400 W. For full-load conditions, compute the induced torque,T-ind, in N-m.