Design and develop equivalent circuit model of a single phase Induction motor with th consideration of core losses present with the parameter consideration of stator resistance R1 and reactance X1 and two rotor parameters which includes r2,x2 and magnetising reactance xm. (Illustration is required) Draw by hand please

Design and develop equivalent circuit model of a single phase Induction motor with th consideration of core losses present with the parameter consideration of stator resistance R1 and reactance X1 and two rotor parameters which includes r2,x2 and magnetising reactance xm. (Illustration is required) Draw by hand please

Electricity for Refrigeration, Heating, and Air Conditioning (MindTap Course List)

10th Edition

ISBN:9781337399128

Author:Russell E. Smith

Publisher:Russell E. Smith

Chapter8: Basic Electric Motors

Section: Chapter Questions

Problem 28RQ: What are the advantages and disadvantages of using the following types of motors? shaded-pole...

See similar textbooks

Similar questions

Would a positive-rotating harmonic or a negative-rotating harmonic be more harmful to an induction motor? Explain your answer.
What are the advantages and disadvantages of using the following types of motors? shaded-pole motor PSC motor split-phase motor capacitor-start–capacitor-run motor
The rotor resistance and reactance per phase of a 4-pole, 50-Hz, 3-phase induction motor are 0.025 ohm and 0.12 ohm respectively. Make simplifying assumptions, state them and : (i) find speed at maximum torque (ii) find value of additional rotor resistance per phase required to give three-fourth of maximum torque at starting. Draw the equivalent circuit of a single-phase induction motor.
A three-phase induction motor, operating at rated voltage and frequency, has a startingtorque of 1.35 times and a maximum torque of 2.2 times, both with respect to its rated-loadtorque. Ignoring the effects of the stator resistance and rotational losses and assumingconstant rotor resistance, determine the slip rated load, and the rotor current at starting (as a percentage of the rotor current at rated load). The slip at maximum torque is 0.343 if that helps.
5.a. A motor which is designed with nonstandard operating characteristics is classified as aA. definite-purpose motor.B. special-purpose motor.C. general-purpose motor. 5.B. For a repulsion motor with bmshes set in the neutral position, what type of winding is needed to producestarting torque?A. A capacitor-phase windingB. A squirrel-cage windingC. A starting winding
Three-phase induction motor, 460 V 50 Hz, 4 poles, 50 hp with Delta, operating at 3.8% slip rated torque when receives Line Voltage 460 V, 50 Hz The parameters of the equivalent circuit per phase are as follows.R1 = 0.33, X1 = X2 = 0.42 and Xm = 30 Ohm / phase.Answer the following questions by neglecting the mechanical losses, Core losses and Stray load losses.A) Value of the rotor resistance R2 B) Maximum torque and rated speed C) line current and starting torque of motor
1. What is the formula for torque production in a single-phase induction motor? Draw a vector diagram for capacitor start single-phase induction motor.2. Which type of starter is popular for using in induction motor and why?
Q2. For a 10 kW, 380V, three-phase, four-pole, 1200 r/min, delta-connected induction motor. Adopt a specific magnetic loading of 0.4712 Wb/m2 and a specific electric loading of 23000 ampere-conductors per metre. The motor has a full-load efficiency of 85% and a full-load power factor of 0.8. A square pole design may be assumed and the stator leakage impedance voltage drop may be ignored. Assume also that the winding is full-pitched and uniformly wound. To calculate the following design parameters (a) The approximate outer diameter and length of the rotor core (b) the air gap length of the motor (c) the turns per phase (d) the number of conductors per slot, if 3 slots per pole per phase are chosen
A 50-KW, 220V, 50 Hz, squirrel-cage three-phase induction motor is needed to rotate a mine conveyor belt drive. The motor starts sometimes under load, but most of the time is needed to run at rated speed and slip of 3.5%. Propose an appropriate design of this drive motor in order to suit the application. Motivate and then illustrate your design with suitable drawings and speed (slip)-torque graphs.
3-phase 3730W, 220V, 6-pole and 50 Hz induction motor operates at full load with a slip of 0.025. The sum of the rotational losses including friction + windage losses and other (stray load) losses is 5% of the output power. Find the induced (electromagnetic) moment at full load
electrical machines Explain the load operation test by drawing the test connection diagram of the induction motor.Describe briefly drawing the loaded operating characteristic.
The air-gap flux density of a two-pole induction motor is given by B=Bm cos(ωt−θ)where Bm is the peak flux density, θ is the angular displacement around the air gap, and we have assumed clockwise rotation. Give the corresponding expression for the flux density of a four-pole induction motor; of a six-pole induction motor.