Answered: A 3-phase induction motor is wound for…

A 3-phase induction motor is wound for 6-pole and is supplied from 50 Hz system calculate (i) the speed of the motor when slip is 6% and (ii) the rotor current frequency the motor runs at 500 r.p.m.

Electricity for Refrigeration, Heating, and Air Conditioning (MindTap Course List)

10th Edition

ISBN:9781337399128

Author:Russell E. Smith

Publisher:Russell E. Smith

Chapter8: Basic Electric Motors

Section: Chapter Questions

Problem 28RQ: What are the advantages and disadvantages of using the following types of motors? shaded-pole...

See similar textbooks

Related questions

Q: A resistor of 25 ohm is connected in series with a capacitor of 45μF. Calculate the impedance, and…

Q: John is measuring 2Vpp 1kHz waveform with settings of 500 mV/div and 100 ns/div. As it turns out,…

A: The screen of cathode ray oscilloscope is divided into a two-dimensional grid, for example, a 10×10…

Q: 3. Somebody is jumping a car and they did not connect the red cable to the red terminals (+) and the…

Q: 5. Draw the circuit corresponding to the below layout, and indicate the size for each transistor -…

Q: A 40-km, 220-kV, 60-Hz three-phase overhead transmission line has a per-phase resistance of 0.15…

A: Transmission lines are essentially a component of an electrical system that transport electrical…

Q: 20 The alternating voltage e₂ in Fig. 24a is given by the expression e₂ = 20 cos (360 ft - 0) If =…

Q: 100 kW, 250V generator is paralleled with a 300 kW, 250 V generator. Both generators have the same…

Q: Question- A permanent magnet moving coil type ammeter and moving iron type ammeter are connected in…

A: Given- moving coil ammeter & moving iron type ammeter in series. Half wave rectifier voltage…

Q: Reg. b 40 0 ww ww 70 02 5002 09

Q: Solve for VCE of Figure 431 if RB 483 kohms, Rc-2.4 kohms, RE=1.2 kohms and Vcc=18V. VCE=____V RB…

Q: 200v J25A ť ㅇ느 풍 V (E) _ ) VP I Ples= P(t) dt 류 UpIp lavo To 나들 ㅇ avp IDL에 aup Isla-음) 앞ㅋㅋ 외ㅛㅋㄱ죠 옴…

Q: An ultrasonic beam of frequency 1 Mhz and intensity 0.5 w/sq cm passes through a layer of soft…

A: We need to find out the thickness of layer for given power ratio

Q: Which switching technology will work best for high power, high voltage (greater than 6kV), high…

A: Switching frequency: Switches are used to turn ON and turn OFF the device. the switch can connect or…

Q: A voltmeter having a f.s.d. of 100V and a sensitivity of 1.6 kohm/V is used to measure voltage V1 in…

A: Given: f.s.d=100V Sensitivity=1.6kΩ/V Circuit :

Q: In a three-phase star connected alternator it is necessary to generate 1800 line voltage at…

Q: 2 a (ON) 3 14: 3 b .(.o.f...)... u coon 3 Hello expert, I need to convert the drawing from…

A: For the given circuits we need to convert in typography form from handwriting. Here I am going to…

Q: Is d/s V 3H 102 Fig. 8 2 F ing 12.5mF

Q: define engineering economics in 100 words.

A: Given: engineering economics To define: engineering economics in 100 words.

Q: Discuss the procedure of installation, direction of testing to be done, and the commissioning of the…

Q: In the circuit shown below, VDD = 3.3 V, VG=1.1 V, W/L = 9, μp Cox = 50 μA/V²,1 VTH = 0.5 V, C= 25 p…

Q: Q1) Consider a two point charges Q1-5μµc at (1,0,1), and Q2= 2 uc at (1, 180°, 1) in free space…

Q: Please explain why the waveform of information and carriers signal is different from the receiver…

A: According to the question, we need to explain why the waveform of information and carrier signal is…

Q: What is the RMS value of the square wave with an amplitude of 50 A and a period of 20 ms shown…

A: Given data, Waveform is given as,

Q: Use a Karnaugh map to simplify the following standard POS expression (X + Y + Z(X + Y + ZX + Y +…

A: The POS expression is the opposite expression to SOP form. The '0' can be placed for the given…

Q: A small household has the following appliances: a 150-W refrigerator, five 12-W LED bulbs, a 60-W…

A: Given: 150-W refrigerator, Five 12-W LED bulbs, A 60-W LED TV, Two 600-W window air conditioner, A…

Q: What type of feedback controller is shown in figure A. PD controller B. PI controller C. Type 2 D.…

Q: Given: the SISO LTI system: Determine: G(s) = s+10 s² +0.5s +1 2 a) the poles and zeros of the…

A: Since you have posted a question with multiple sub-parts, we will solve first three sub-parts for…

Q: V1 10 R5 5k R1 10k R2 M 12k R6 9k R3 10k. a R4 20k R7 15k

Q: Coal Plant = 600 MW O Industrial Power Plant Factory no no no no no 10 ≈ 30 MW City Network no no no…

A: First we have to understand basic functionality of every electricity generation plant. - coal plant-…

Q: Arrange the chronological order of the elements and its function to Digital Communication by writing…

A: Digital communication is the process of sending digital data to various locations, when analog data…

Q: Problem 8 For the amplifier circuit shown, find the following characteristics: voltage gain A =…

Q: Solve for R₁ R₁ VB 5.6 ΚΩ 34.9kohm 39.4Mohm 39.4kohm 34.9Mohm - 18 V 4.7 ΚΩ Ic oVc = 12 V 1.2 ΚΩ VE

Q: The variable resistor R in the circuit in (Figure 1) is adjusted until va equals 50 V. Suppose that…

A: We need to find out the unknown value of resistor for given circuit

Q: Explain the detailed process of Power Grid Extension

A: Extension of the transmission and distribution network to places where there is insufficient or no…

Q: DESIGN a 3-bit counter using, T-FF that counts 0-7 and repeats. I need a design, tables, logic gates…

A: Counter: It is a device that stores the number of events or processes that occurred in relation to…

Q: b- Using physical equations, is the number of photons in one joule of red light greater than, equal…

A: Given that w have to compare that no of photons in one joule of red light is greater,lesser and…

Q: 6.) A circular wire loop is oriented in the x-y plane and has a radius of r and a resistance of R. A…

A: We need to find out induced EMF and current

Q: +120 V- Vin OV -120 V 00000 2:1 00000 D₁ Si D₂ Si Va out Figure 3 8) How much is the peak load…

Q: 9) a. Use DeMorgan's Theorem to simplify the following Boolean equations: Y = ABCD b. Y= ABCDE C.…

Q: Using physical equations, is the number of photons in one joule of red light greater than, equal to,…

A: Given that w have to compare that no of photons in one joule of red light is greater,lesser and…

Q: The Fourier series coefficient of time domain signal x (t) is X[k] = jδ[k-1] – jδ[k+1] + δ[k+3] +…

Q: a) 5W b) 24 W Q11) The Va for the the circuit shown in Fig. 7 as seen from the terminal a-b can be…

A: This is a problem of circuit. The solution is given in the next step

Q: A 3-phase star connected 1000 V alternator supplies power to 500 kW delta- connected induction…

Q: Find the Laplace transforms of (a) 214 e³t (b) 4e³t cos 5t.

Q: Find the Fourier series coefficient of the signal y(t) = Even{x(t)}

A: Given,The signal function is,yt=EvenxtHere,We have to find the fourier series coefficient of the…

Q: 1. Show calculations in step by step manner. Draw a box around the final answer. Include units. 110…

Q: A moving-coil instrument gives a f.s.d. when the current is 40 mA and its resistance is 25 12.…

A: Given that Resistance of the instrument ri = 25Ω Permissible current flowing in instrument Ii= 40 mA…

Q: 04/ Answer the following questions. a-Why should the transition probability be calculated in terms…

Q: of Fig. 12 for the following questions (Q20 d) 15 V e) 24 V Q20) (0) can be found as: a)30 V b) 12.5…

A: We need to find out the voltage across capacitor

Q: A pipe contains an oil of specific gravity 0.9. A Differential manometer Connected at the two points…

Concept explainers

Three Phase Induction Motor

The induction motor is an electric motor that runs on AC (alternating current) and it is of two type single phase motor that work on single-phase power supply and three-phase motor that work on three-phase power supply.

Question

A 3-phase induction motor is wound for 6-pole and is supplied from 50 Hz system calculate (i) the speed of the motor when slip is 6% and (ii) the rotor current frequency the motor runs at 500 r.p.m.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

What are the advantages and disadvantages of using the following types of motors? shaded-pole motor PSC motor split-phase motor capacitor-start–capacitor-run motor
3-phase induction motor is wound for 8-pole and is supplied from 50 Hz system calculate (1) the synchronous speed, (ii) the speed of the motor when slip is 8% and (iii) the rotor current frequency when the motor runs at 1200 r.p.m.
A 3 phase induction motor is wound for 6 poles and is supplied fromn 50-Hz system. Calculate 1) the synchronous speed 2) the rotor speed, when slip is 2% and 3) the frequency of the rotor currents at standstill.
Q)A 3phase induction motor is wound for 6 poles and is supplied fromn 50-Hz system. Calculate 1. the synchronous speed 2. the rotor speed, when slip is 2% and 3. the frequency of the rotor currents at standstill.
A three-phase, 415V, 50Hz, six-pole, star-connected induction motor is driven from a variable voltage, variable frequency supply. The motor circuit phase parameters are as follows: R₁ = R' = 1.002, X₂=X₂ = 2.002, Xm=502 When running at full load on rated voltage and frequency, the motor takes a line current of 12A at 0.86 power factor lagging. Assuming that the motor is operating in the constant flux mode, determine the supply voltage and speed when delivering the same torque at 60Hz.
A three phase induction motor with supply frequency of 60 Hz, 8 poles. If the slip is 2.5 % at a certain load, determine (a) the synchronous speed, (b) the speed of the rotor (c) the frequency of the induced e.m.f in he rotor and (d) speed of the induction motor if the slip changes to 6 %
A four-pole, single-phase, 120 V, 60 Hz induction motor gave the following standstill impedances when tested at rated frequency:Main winding : Zm =1.5+j4 ohmsAuxiliary winding : Za =3+j6 ohmsa) Determine the value of external resistance to be inserted in series with the auxiliary winding to obtain maximum starting torque as a resistor split-phase motor.b) Determine the value of the capacitor to be inserted in series with the auxiliary winding to obtain maximum starting torque as a capacitor-start motor.c) Determine the value of the capacitor to be inserted in series with the auxiliary winding to obtain maximum starting torque per ampere of the starting current as a capacitor-start motor.d) Compare the starting torques and starting currents in parts (a), (b), and (c) expressed as per unit of the starting torque without any external element in the auxiliary circuit, when operated at 120V, 60Hz.
A 3-phase star connected induction motor has a 4-pole, stator winding. The motor runs on 50 Hz supply with 230 V between lines. The motor resistance and standstill reactance per phase are 0.25Ω and 0.8 Ω respectively. CalculateThe total torque at 5 %, The maximum torque, The speed of the maximum torque if the ratio of the rotor to stator turns is 0.67 whilst neglecting stator impedance.
A 3-phase 9-pole,50Hz, star connected induction motor has an emf 520 V(L-L). The stator winding has a synchronous reactance of 2.5 Ohms/phase. Induction machine operates at rated voltage and at a leading power factor of 0.85. Shaft power is 15 Kw and the excitation emf is 500 V. (a). Determine the load angle, armature current in per unit and the power factor of the alternator. (b). The alternator is now made to operate at another value of excitation emf which results in the same values of power output and armature current. Under these conditions, find the excitation voltage, load angle and the power factor. (c) If the excitation in (a) and that obtained in (b), which is more likely to be used in practical situations and and why? (d) With the alternator output remaining constant, the alternator excitation is increased by 15%. Find the new values of armature current, load angle and pf? (e) Calculate the total steam output of the alternator delivered to the prime mover? (f) Draw the…
A 110-V, 50-Hz single phase induction motor (split -phase) has the following constants for the main and auxiliary windings: Main winding, Zm (1.2 +j 25) ohm and auxiliary winding, Z,= (12+j 5) ohm. Determine (i) total current and power factor currents at time of starting, and (ii) phase angle between the main winding current and starting winding current.
A 3-phase induction motor is wound for 4 poles and is supplied from 50-Hz system. Calculate the synchronous speed the rotor speed, when slip is 4% and rotor frequency when rotor runs at 600 rpm.
A 3,3 kV, 50 HZ, three-phase, star connected induction motor, with an output of 100 kW, has a synchronous speed of 500 r/min. The full-load slip is 1,8 % and the full load power factor is 0,85 lagging. The stator copper loss is 2,44 kW, the stator iron loss is 3,5 kW and the rotational losses are 1,2 kW. Calculate: a) the rotor copper loss (PCuR), b) the line current and c) the full load efficiency