A 3.6 m long overhang timber beam AC with a 2.4 m span AB is to be designed to support the distributed and concentrated loads shown. a. Determine the maximum moment of the beam. b. Determine the minimum required depth of the beam if the allowable stress is 12 MPa. c. Determine the maximum shearing stress of the required beam. 20 kN 90 mm 60 kN/m d 2.4 m 1.2 m

A 3.6 m long overhang timber beam AC with a 2.4 m span AB is to be designed to support the distributed and concentrated loads shown. a. Determine the maximum moment of the beam. b. Determine the minimum required depth of the beam if the allowable stress is 12 MPa. c. Determine the maximum shearing stress of the required beam. 20 kN 90 mm 60 kN/m d 2.4 m 1.2 m

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

For the wide-flange beam with the loading shown, determine the largest load P that can be applied, knowing that the maximum normal stress is 160 MPa and the largest shearing stress is 100 MPa. W360 x 122 B
Determine the maximum load F that can be applied at the free end of a 3 m cantilever beam of universal rolled-steel beam cross-section, 356 mm deep, with a moment of inertia of 142 × 106 mm4, if the allowable stress is 76 MPa.
A log that is 2 ft in diameter is to be cut into a rectangular section for use as a simply supported beam. If the allowable bending stress is sallow = 8 ksi, determine the largest load P that can be supported if the width of the beam is b = 8 in.
A cable AB of span L and a simple beam A'B' of the same span are subjected to identical vertical loadings as shown. Show that the magnitude of the bending moment at a point C' in the beam is equal to the product T0h, where T0 is the magnitude of the horizontal component of the tension force in the cable and h is the vertical distance between point C and the chord joining the points of support A and B.
A couple M will be applied to a beam of rectangular cross section that is to be sawed from a log of circular cross section. Determine the ratio d/b for which (a) the maximum stress σm will be as small as pos-sible, (b) the radius of curvature of the beam will be maximum.
Determine (a) the distance a for which the absolute value of the bending moment in the beam is as small as possible, (b) the corresponding moximum normal stress due to bending.
A simply supported beam 4 m long has a cross section shown. Determine the maximum uniformly distributed load which can be applied over the entire length of the beam if the shearing stress is limited to 1.8 MPa. Answer must be in kN/m. Given: b 130 mm and d = 170 mm.
Knowing that the allowable normal stress for the steel used is 160 MPa, select the most economical S-shape beam to support the loading shown.
For the beam with the cross-section shown, given that: V= 100 N b= 20 cm h=20 cm The max shear stress equals:
Knowing that the allowable normal stress for the steel used is 160 MPa, select the most economical wide-flange beam to support the loading shown.
A composite beam is made by attaching the timber and steel portions shown with bolts of 12-mm diameter spaced longitudinally every 200 mm. The modulus of elasticity is 10 GPa for the wood and 200 GPa for the steel. For a vertical shear of 4 kN, determine (a) the average shearing stress in the bolts, (b) the shearing stress at the center of the cross section.
Q3 / For the beam and loading shown, determine the maximum normal stress due to bending.