Q.5 A 300-g cylinder C rests on cylinder D as shown. Knowing that the coefficient of static frictionu, is the same at A and B, write a computer program and use it to determine, for values of u,from 0 to 0.40 and using 0.05 increments, the largest counterclockwise couple M that can beapplied to cylinder Dif it is not to rotate.75 mmA150 mmM150 mmFig. P8.C3

Given data-μ=0.35d=75mmD=150mm

A 300-g cylinder C rests on cylinder D as shown. Knowing that the coefficient of static friction l, is the same at A and B, write a computer program and use it to determine, for values of us from 0 to 0.40 and using 0.05 increments, the largest counterclockwise couple M that can be applied to cylinder Dif it is not to rotate. 75 mm

A 300-g cylinder C rests on cylinder D as shown. Knowing that the coefficient of static friction l, is the same at A and B, write a computer program and use it to determine, for values of us from 0 to 0.40 and using 0.05 increments, the largest counterclockwise couple M that can be applied to cylinder Dif it is not to rotate. 75 mm

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter7: Dry Friction

Section: Chapter Questions

Problem 7.4P: The two homogeneous bars AB and BC are connected with a pin at B and placed between rough vertical...

See similar textbooks

Similar questions

A safety device used by workers climbing ladders fixed to high structures consists of a rail attached to the ladder and a sleeve that can slide on the flange of the rail. A chain connects the worker’s belt to the end of an eccentric cam that can be rotated about an axle attached to the sleeve at C. Determine the smallest allowable common value of the coefficient of static friction between the flange of the rail, the pins at A and B , and the eccentric cam if the sleeve is not to slide down when the chain is pulled vertically downward.
A safety device used by workers climbing ladders fixed to high structuresconsists of a rail attached to the ladder and asleeve that can slide on theflange of the rail. A chain connects the worker’s belt to the end of aneccentric cam that can be rotated about an axle attached to the sleeve at C.Determine the smallest allowable common value of the coefficient ofstatic friction between the flange of the rail, the pins at A and B, and theeccentric cam if the sleeve is not to slide down when the chain is pulledvertically downward.
Solve Prob. 8.126 assuming that 0= 75°.(Reference to Problem 8.126):The strap wrench shown is used to grip the pipe firmly without marring the external surface of the pipe. Knowing that the coefficient of static friction is the same for all surfaces of contact, determine the smallest value of μs for which the wrench will be self-locking when a = 200 mm, r=30 mm, and 0= 65°.
The position of the automobile jack shown is controlled by a screw ABC that is single-threaded at each end (right-handed thread at A, left-handed thread at C ). Each thread has a pitch of 2.5 mm and a mean diameter of 9 mm. If the coefficient of static friction is 0.15, determine the magnitude of the couple M that must be applied to raise the automobile.
Solve Prob. 8.113 assuming that the belt is looped around the pulleys in a figure eight.(Reference to Problem 8.113):A flat belt is used to transmit a couple from pulley A to pulley B . The radius of each pulley is 60 mm, and a force of magnitude P = 900 N is applied as shown to the axle of pulley A . Knowing that the coefficient of static friction is 0.35, determine (a) the largest couple that can be transmitted, (b) the corresponding maximum value of the tension in the belt.
An elevator type lift is being designed to raise a load up to 5,000pounds between floors. Twosquare-thread lead screws, 1.5 inches in (major) diameter, are used for this application. Determine the torque required to raise this lift if the moving part of the elevator weighs 800 pounds and the coefficient of friction is assumed to be 0.15.
The elevation of the end of the steel beam supported by a concrete floor is adjusted by means of the steel wedges E and F . The base plate CD has been welded to the lower flange of the beam, and the end reaction of the beam is known to be 100 kN. The coefficient of static friction is 0.30 between two steel surfaces and 0.60 between steel and concrete. If the horizontal motion of tin beam is prevented by the force Q . determine (a) the force P required to raise the beam, (b) the corresponding force Q
The square-threaded worm gear shown has a mean radius of 2 in. and a lead of 0.5 in. The large gear is subjected to a constant clockwise couple of 9.6 kip.in Knowing that the coefficient of static friction between the two gears is 0.12, determine the couple that must be applied to shaft AB in order to rotate the large gear counterclockwise. Neglect friction in the bearings at A, B, and C.
A lever AB of negligible weight is loosely fitted onto a 2.5-in.-diameter fixed shaft. Knowing that the coefficient of static friction between the fixed shaft and the lever is 0.15, determine the force P required to start the lever rotating clockwise.
A homogeneous bar AB of weight W and length L is lifted by force P that is perpendicular to bar. Determine the smallest coefficient of static friction at A thst would enable the bar to reach the position 30°
A slender steel rod with a length of 225 mm is placed inside a pipe as shown. Knowing that the coefficient of static friction between the rod and the pipe is 0.20, determine the largest value of 0 for which the rod will not fall into the pipe.
High-strength bolts are used in the construction of many steel structures. For a 1-in.-nominal-diameter bolt, the required minimum bolt tension is 51 kips. Assuming the coefficient of friction to be 0.30, determine the required couple that should be applied to the bolt and nut. The mean diameter of the thread is 0.94 in., and the lead is 0.125 in. Neglect friction between the nut and washer, and assume the bolt to be square-threaded.