A 300mm by 600mm rectangular beam is subjected to uniform ultimate load of Wu=200kN/m over the whole span. The beam is simply supported over a span of 4m. The reinforcements are 2-28 mm diameter compression reinforcement and 4-28 mm diameter tension reinforcement. Use f'c=21MPa, fy=415MPa, stirrups=10mm, and cc=40mm.   Calculate the maximum positive moment in the beam in kN.m.0 Calculate the depth of compression block in the beam in mm.0 Calculate the stress in the compression compression reinforcement in MPa.0 Calculate the ultimate moment capacity of the beam section in kN.m.0

Q: y and 1.2 meters below. The p O Pa. If the flow rate when the at least .0126 m^3/s, what is th pipe?...

A:

Q: hm 25mm diameter 75mm 2m diameter water 200mm 600mm Mercury (SG 13.6) ---- The head lost from point ...

A: Given data,  S.G of mercury = 13.6 Head loss = 4 m To find out the velocity  at 1 and hm. 

Q: Given the following information, calculate the reactions at both supports for beam DI. Live Load, LL...

A:

Q: 4. A piece of wood contains a glued joint inclined at an angle as shown in the figure. If the dimens...

A:

Q: Pair of beams (AB) and (CDE) are connected by cable BC and subjected to the concentrated and distrib...

A:

Q: Civil Engineering A sample of soil with LL of 72.8 was found to have a liquidity index of 1.21 and w...

A: Given data  LL = 72.8 LI = 1.21 WC = 81.3      

Q: A body, with a volume of 2 cubic meter, weighs 40 KN. Determine its weight when submerged in a liqui...

A:

Q: Write the shear and moment equations (not simplified and simplified segment . the beam shown. Also d...

A:

Q: *Part C - Calculating the moment about AB using the position vector BC Using the position vector fro...

A: Given Data -

Q: Why the figure has 2.5 sg and 4 sg?

A: Here, we have to explain why the figure given has 2.5sg & 4sg .

Q: A car is to be hoisted by elevator to the fourth floor of a parking garage, which is 41.69 ft above ...

A:

Q: The concrete slab shown in the picture is subject to four forces, F1=125 lb, F2=260 lb, F3=675 lb, a...

A: Given: The value of F1 is 125 lb. The value of F2 is 260 lb. The value of F3 is 675 lb. The value of...

Q: What is the volume of the cut (m3) using the prismoidal correction formula?

A: Volume of cut using prismoidal formula is given by:- V=d/3*(A1+An+4(A2+A4+...)+2(A3+A5+...)) This fo...

Q: Draw the load and moment diagrams

A:

Q: 1. The dimension of the display window at the Georgia aquarium is 5m x 5m. Ašsum that the aquarium c...

A: Given data - To find-

Q: Problem 1. Use slope-deflection method and determine the following unknowns on the beam shown  below...

A: Given data Length of span (L) = 3.4m   0.7L = 0.7×3.4 = 2.38m  0.3L = 0.3×3.4 = 1.02m   

Q: A bottling plant has 217,427 bottles with a capacity of 475 mL, 188,700 caps and 96,345 L of beverag...

A:

Q: Investigate

A:

Q: • A concrete wall footing with a width of 0.9m and a depth of 0.6m supports a centrally placed 0.6-m...

A:

Q: Classify the following 3 soils by the AASHTO soil classification system. Sieve Analysis, % Finer No....

A: To Determine Classify the given Soil samples according to AASHTO soil classification system. Please ...

Q: 1) II) Find the depth D, in which the wood will be submerged. Is the wood cylinder stable? Show your...

A:

Q: For the punching operation shown in the figure, compute the shear stress (in GPa) in the material if...

A:

Q: Should or should not an engineer who has prepared plans and specifications for a piece of work bid o...

A: Construction bidding is the practise of a contractor offering a tender to a client as a proposal to ...

Q: Determine the horizontal force reaction at joint 1. A-9.12 in. 1-375 in. 21 A= 10.3 in 1-285 in. 1 k...

A:

Q: Determine the angle of intersection.

A: This question is related to the Simple Curve form Surveying Engineering. In this question we calcula...

Q: Enumerate the steps in determining the ultimate moment strength of a singly-reinforced RC beam. Expl...

A:

Q: What are the importance of the Code of Ethics for the Sanitary Engineers professional practice. ...

A: 1) code of ethics is important for an sanitary engineer to maintain honesty, morality and  being tru...

Q: Q2.Using LRFD procedure, investigate the shear rupture failure mode for the angle L 152*152*7.9, att...

A:

Q: 40mm L-600mm P = 20kN 20mim

A:

Q: Prob. 3): A circular shallow foundation has been constructed at depth D, of 2 m. The gross allowable...

A: Note:  As there are three problems and only one problem can be solved. So please resubmit the remain...

Q: Ellen wishes to mix candy worth $1.55 per pound with candy worth $7.14 per pound to form 26 pounds o...

A: The values given in the question are as follows: First candy worth(P1)=$1.55 per pound Second Candy ...

Q: W, L2

A:

Q: .5 Prepare a set of profile leveling notes for the survey in Figure 2-34. In addition to comput- ing...

A: Prepare a set of profile leveling notes for the survey in Figure 2-34. In addition to comput ing all...

Q: The concrete slab shown in the picture is subject to four forces, F1=125 lb, F2=260 lb, F3=675 lb, a...

A:

Q: drillpipe and 1000 ft of drill collars having a 3.0-in. ID. COmpute the following items: a capacity ...

A: Note -As per company's guidelines we are allowed to solve 1st three subparts. Kindly post the remain...

Q: The square steel tube carries 100kN of axial compressive force. Compute the compressive stress in th...

A:

Q: Problem 2: Draw the shear and moment diagram of the indeterminate beam. 15KN/m 60KN 60KN 8kN/m 7m 3m...

A: Calculation of Distribution Factors

Q: The tangents of a simple curve have bearings of N 71°22’ E and S 76°45’ E respectively. A four-degre...

A: Given - The tangents of a simple curve have bearings of N 71°22’ E and S 76°45’ E respectively. A fo...

Q: Two industries Fuzzy Chemicals and Super Agra want to discharge their wastewater into the Delaware R...

A:

Q: Consider a trapezoidal channel conveys water with bottom width of 7 m and side slope of 2:1. The bed...

A: As per rule I can give only one answer because in the second part more than two or three sub parts s...

Q: Determine the time required for a car to travel 13.039 km along a road if the car starts from rest, ...

A:

Q: .5 Prepare a set of profile leveling notes for the survey in Figure 2-34. In addition to comput- ing...

A: To Determine Prepare a set of profile leveling notes for the survey. Computing all elevations, Show ...

Q: .) A quart of SAE 30 oil at 68 °F weighs about 1.85 lb. Calculate the oil's specific weight, mass de...

A:

Q: Four forces (including the weight of the cylinder) are applied to a ring at point A as shown. Knowin...

A: Weight of the cylinder = 1000lb Angle between 750lb force and negative x axis         = tan-1(3/4) =...

Q: Calculate the amount of lime and soda required to treat tuwo million litre (M.L.) of hard water, con...

A:

Q: For a simply supported prestressed concrete beam, compute the stress in the bottom fiber at the cent...

A:

Q: In preparation of the earthworks of a proposed road, given below are the three-level cross section n...

A:

Q: The indeterminate frame below is loaded with gravity loads as shown. Using MOMENT DISTRIBUTION METHO...

A: As per our company guidelines we are supposed to answer only first 3 sub-parts. Kindly repost other ...

Q: 1. A block of wood having a volume of 0.034m3 and weighing 300N is suspended in water as shown. A wo...

A: ##DETERMINATION OF ANGLE ALPHA###  

Q: A rectangular footing 1.64 x 2.31 meters in plan. The soil supporting the foundation has a friction ...

A:

Beams

In structural engineering, a beam is a component made of a variety of materials (including steel alloys, and wood) that can resist loads applied laterally to the beam axis. Members, elements, rafters, shafts, and purlins are all terms used to describe beams.