A 325mmx475mm (bxh) 7.75m simple beam carries a total dead load of 22KN/m and a live load of33KN/m. Clear cover is 40mm, diameter of shear reinforcement to be 10mm, concrete strengtn to be28MPA, steel strength for transverse reinforcement to be 420MPA and reinforced with 4D28mm rebar 1layer.Determine the balanced steel area in mm2.Your answerDetermine the maximum steel area using a steel strain of 0.004, mm2.Your answerDetermine the maximum moment using a steel strain of 0.005, kN-m.Your answerDetermine the design strength in kN-m.Your answer

NOTE: Since we only answer up to 3 sub-parts, we’ll answer the first 3. Please resubmit the question…

A 325mmx475mm (bxh) 7.75m simple beam carries a total dead load of 22kN/m and a live load of 33KN/m. Clear cover is 40mm, diameter of shear reinforcement to be 10mm, concrete strength to be 28MPA, steel strength for transverse reinforcement to be 420MPa and reinforced with 4028mm rebar 1 layer. Determine the balanced steel area in mm2. Your answer Determine the maximum steel area using a steel strain of 0.004, mm2. Your answer Determine the maximum moment using a steel strain of 0.005, kN-m. Your answer Determine the design strength in kN-m. Your answer

A 325mmx475mm (bxh) 7.75m simple beam carries a total dead load of 22kN/m and a live load of 33KN/m. Clear cover is 40mm, diameter of shear reinforcement to be 10mm, concrete strength to be 28MPA, steel strength for transverse reinforcement to be 420MPa and reinforced with 4028mm rebar 1 layer. Determine the balanced steel area in mm2. Your answer Determine the maximum steel area using a steel strain of 0.004, mm2. Your answer Determine the maximum moment using a steel strain of 0.005, kN-m. Your answer Determine the design strength in kN-m. Your answer

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter9: Composite Construction

Section: Chapter Questions

Problem 9.10.2P

See similar textbooks

Similar questions

Determine the numbers of rebars required for a RC beam (h=400mm, b=700mm) carrying a factored moment of 796 kPa. The concrete used has a compressive strength of 28MPa, while steel yields at 345MPa. Assume single layer of reinforcements (compression and/or tension side) and do not check for rebar spacing anymore. Other parameters: Cc = 40mm db = 20mm ds = 10mm Provide illustration if necessary and answers must be in 3 decimal places.
a simply supported beam 300mm wide, 500mm deep and spans 5.7m supports a service super imposed dead load of 8kN/m and service live load of 7kN/m. concrete strength f'c=21MPa and steel yield strength fy=415MPa. concrete cover to bar centroid is 70mm. determine the required amount of tensile reinforcement in mm^2 as per provisions of NSCP 2015.
Problem No. 3 A beam 200x450mm is reinforced by 2-32mm diameter rebar. Assume cc-50mm, stirrups-10mm, fc'-21Mpa and fy-415Mpa. Calculate the following. 18. Calculate the strain of the steel reinforcement
30" Design the reinforcement for the T-beam in the middle which carries a live load of 200 lb/ft². The length of the beam is 25 ft. In your design assume concrete with a compressive strength of 3,000 psi density 150 lb/ft³ and Grade 60 Steel. 27" 12" 10'-0" 12" 10'-0" 12"
Determine the numbers of rebars required for a RC beam (h=400mm, b=700mm) carrying a factored moment of 734 kNm. The concrete used has a compressive strength of 28MPa, while steel yields at 345MPa. Assume single layer of reinforcements (compression and/or tension side) and do not check for rebar spacing anymore. Other parameters: Cc = 40mm db = 20mm ds = 10mm
A simply supported beam is reinforced with 5-p25 mm at the bottom and 2-020 mm at the top of the beam. Concrete covering to centroid of reinforcement is 70 mm at the top and 64 mm at the bottom of the beam. The beam has a gross depth of 450 mm and gross width of 300 mm. fc'= 28 MPa, fy = 415 MPa. Assume bars laid out in single layer. Calculate the following if the limiting tensile steel strain is 0.004 for a ductile failure: Depth of the neutral axis from the extreme concrete compression fiber to the nearest whole number = mm Design strength of the beam section to the nearest whole number = kN -m Maximum service uniform live load over the entire span in addition to a DL = 20 kN/m (including the weight of the beam) if it has a span of 6 m = kN/m (to the nearest whole number)
a 450mm diameter concrete spiral column is to be designed to support a factored axial load of 3170kn. clear bar cover is 40mm and tge aggregate soze is 25mm. use nscp 2010 with fc'= 28mpa, fy= 414mpa for longitudinal steel, fyt= 414mpa for spiral steel. limit the gross percentage to 2%. which of the following most nearly gives the clear spacing of the main longitudinal reinforcements in mm.
Refer to the figure shown below. 350 Given are the following: fc 55 MPa fou 1,350 MPa Aps - 1.500 mnm2 fpy - 1,100 MPa Use bonded tendons as prestressed reinforcement. Determine the design monment capacity of the section. (kN-m)
A simply supported beam is reinforced with 5-ϕ25 mm at the bottom and 2-ϕ20 mm at the top of the beam. Concrete covering to centroid of reinforcement is 70 mm at the top and 64 mm at the bottom of the beam. The beam has a gross depth of 450 mm and gross width of 300 mm. fc’= 28 MPa, fy = 415 MPa. Assume bars laid out in single layer. Calculate the following if the limiting tensile steel strain is 0.004 for a ductile failure: Depth of the neutral axis from the extreme concrete compression fiber to the nearest whole number = __ mm
A simply supported beam is reinforced with 5-ϕ25 mm at the bottom and 2-ϕ20 mm at the top of the beam. Concrete covering to centroid of reinforcement is 70 mm at the top and 64 mm at the bottom of the beam. The beam has a gross depth of 450 mm and gross width of 300 mm. fc’= 28 MPa, fy = 415 MPa. Assume bars laid out in single layer. Calculate the following if the limiting tensile steel strain is 0.004 for a ductile failure: Depth of the neutral axis from the extreme concrete compression fiber to the nearest whole number = mm Design strength of the beam section to the nearest whole number = kN·m Maximum service uniform live load over the entire span in addition to a DL = 20 kN/m (including the weight of the beam) if it has a span of 6 m = kN/m (to the nearest whole number)
A simply supported beam is reinforced with 5-ϕ25 mm at the bottom and 2-ϕ20 mm at the top of the beam. Concrete covering to centroid of reinforcement is 70 mm at the top and 64 mm at the bottom of the beam. The beam has a gross depth of 450 mm and gross width of 300 mm. fc’= 28 MPa, fy = 415 MPa. Assume bars laid out in single layer. Calculate the following if the limiting tensile steel strain is 0.004 for a ductile failure: Maximum service uniform live load over the entire span in addition to a DL = 20 kN/m (including the weight of the beam) if it has a span of 6 m = kN/m (to the nearest whole number)
Design the shear reinforcement of the beam loaded as shown using WSD with fc’ = 20.7 MPa and fy = 276 MPa, fs = (fy/2)