3. A continuous reinforced concrete one-way slab monolithically cast with beams is given below. Service (unfactored) live load is 125 psf. Service dead load is 20 psf, excluding the self-weight of the slab. Consider the height (h=8in), effective depth (d=7in) and flexure reinforcement (As-0.31 sq.in per foot width) for your calculations. Use 3,000 psi compressive strength concrete and Grade 60 reinforcing steel. Design the slab for shear.

3. A continuous reinforced concrete one-way slab monolithically cast with beams is given below. Service (unfactored) live load is 125 psf. Service dead load is 20 psf, excluding the self-weight of the slab. Consider the height (h=8in), effective depth (d=7in) and flexure reinforcement (As-0.31 sq.in per foot width) for your calculations. Use 3,000 psi compressive strength concrete and Grade 60 reinforcing steel. Design the slab for shear.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A rectangular beam has a width of 280 mm and an effective depth of 500 mm. It has a reinforcement area of 4072 sq. mm at the bottom. fc' = 25 MPa, fy = 414 MPa. a) Determine the depth of compression block, "a".
An eight meter simply supported beam carries a superimposed dead load of 6kN/m and aservice live load of 15kN/m. The beam has a width and total depth of 400mm and 550mm respectively.It is reinforced with five diameter 25mm bars and 10mm stirrups. Material properties are fc'=27.60MPaand fy=421.60MPa. 1 Using the detailed calculation of Vc, determine the nominal shear strength of concrete at 0.60m from the support. a 133.3220 kN b 153.6610 kN c 180.3630 kN d 110.5770 kN 2 Using the detailed calculation of Vc, determine the shear carried by stirrups at 0.90m from the support. * a 53.7734 kN b 65.4637kN c 58.3913 kN d 67.2129 kN
A rectangular beam has a width of 280 mm and an effective depth of 500 mm. It has a reinforcement area of 4072 sq. mm at the bottom. fc' = 25 MPa, fy = 414 MPa. c) Determine the value of "Mu"
Design a 350 mm x 500 mm rectangular beam to resist a factored moment of 630 kN-m. Assume concrete over (measured from bar centroid) to be 70 mm in compression and 80 mm in tension. Use fy= 345 MPa and fc= 27.6 MPA
PROBLEM 2: A reinforced concrete beam has a simple span of 7m. It carries a uniformly distributed dead load (including its own weight) of 9kN/m, live load equal to 18kN/m . The beam is reinforced with 3D28mm bars and has a width of 250mm and an effective depth of 450mm. fc’=28Mpa and fy=345Mpa. Using the simplified calculation for Vc, what is the nominal shear capacity of concrete? At what section of the beam is the web reinforcement theoretically not required? At what section of the beam is the web reinforcement no longer required according to the NSCP? Draw the design details for shear of the beam from x=3m to x=3.5m.
Assume fy=345MPa and f′c=21 MPa. From the provided steel reinforcement, will the steel yield? What is the depth of the triangular compression block, measured from the extreme compressionfiber? What is the ultimate moment capacity of the section, in kN-m?
An eight meter simply supported beam carries a superimposed dead load of 6kN/m and a service live load of 15kN/m. The beam has a width and total depth of 400mm and 550mm respectively. It is reinforced with five diameter 25mm bars and 10mm stirrups. Material properties are fc'=27.60MPa and fy=421.60MPa. a. Using the detailed calculation of Vc, determine the nominal shear strength of concrete at 0.60m from the support.
Design a 350 mm x 500 mm rectangular beam to resist a factored moment of 630 kN-m. Assume concrete over (measured from bar centroid) to be 70 mm in compression and 80mm in tension. Use fy = 345 MPa and fc = 27.6 MPa.
Determine the theoretical steel areas required for tension of a rectangular section with b = 350 mm, d = 600 mm under a factored moment of 1,500 kN-m. If compression steel is required, assume it will be placed 70 mm from the compression fiber of concrete. Use fc’ = 28 Mpa and fy = 420 Mpa.Usingabar size of your choice, determine the number of bars required and design the bar lay-out.(For the purpose of laying-out, use 10mm diameter bars for stirrups.)
A doubly reinforced beam, which have a base of 310 mm, and an effective depth of 410 mm, is reinforced with steel area of 2263 sq. mm at the bottom, and 1232 sq. mm on the top. Take d' = 70 mm, fc' = 21 MPa, and fy = 345 MPa. b) What is the value of fs' (actual stress of the compression bars)
A floor systtem consist of a 75 mm concrete slab supported by continuous T beams with a span of 4.3 m spaced at 3 m on center. The beams have a web width, bw and effective depth, d. Calculate the necessary reinforcement for a typical interior beam if the applied factored load is 574 kN-m. Solve the following given a. ) bw = 400 mm; d = 500 mm; fy = 420 MPa; fc' = 28 MPa b. ) bw = 350 mm; d = 470 mm; fy = 420 MPa; fc' = 21 MPa
1. Design a rectangular reinforced concrete beam to resist service moments of 120 kNm from dead loads and 110 kNm from live loads. The beam dimension are (b x d) 0.25m x 0.6m. Assumefck = 25 N/mm2and fyk = 500 N/mm2.2. Check the design from Q1.3. A reinforced concrete beam is 0.25m x 0.450 m (b x d). The tension reinforcement provided is 2H25 (As = 982mm2). Determine the moment of resistance of the section if fck = 25 N/mm2 and fyk = 500 N/mm2.4. By using the information from Q3, calculate the actual area of reinforcement required.5. Design a rectangular reinforced concrete beam to resist service moments of 195 kNm from dead loads and 145 kNm from live loads. The beam dimension are (b x d) 250 x 500 mm. Assume fck = 30 N/mm2 and fyk = 500 N/mm2. The depth to compresssion reinforcement is 45mm.Take until 2 decimal point for each calculation.