A 330 gram ball is attached to one end of a rubber (Young's Modulus= 0.120 GN/m2) wire of diameter 1.32 mm and an unstretched length of 83.0 cm. The other end of the wire is attached to the top of a post. The ball rotates around the post in a horizontal plane such that the angle between the wire and the horizontal is 10.5 degrees. Find the tension in the wire and the increase in the wire's length due to the tension in the wire. Tension = 17.75 ALength cm

A 330 gram ball is attached to one end of a rubber (Young's Modulus= 0.120 GN/m2) wire of diameter 1.32 mm and an unstretched length of 83.0 cm. The other end of the wire is attached to the top of a post. The ball rotates around the post in a horizontal plane such that the angle between the wire and the horizontal is 10.5 degrees. Find the tension in the wire and the increase in the wire's length due to the tension in the wire. Tension = 17.75 ALength cm

Physics for Scientists and Engineers: Foundations and Connections

1st Edition

ISBN:9781133939146

Author:Katz, Debora M.

Publisher:Katz, Debora M.

Chapter14: Static Equilibrium, Elasticity, And Fracture

Section: Chapter Questions

Problem 33PQ: Problems 33 and 34 are paired. One end of a uniform beam that weighs 2.80 102 N is attached to a...

See similar textbooks

Similar questions

A 100-N weight is attached to a free end of a metallic wire that hangs from the ceiling. When a second 100-N weight is added to the wire, it stretches 3.0 mm. The diameter and the length of the wire are 1.0 mm and2.0 m, respectively. What is Young’s modulus of the metal used to manufacture the wire?
An aluminium (=2.7g/cm3) wire is suspended from the ceiling and hangs vertically. How long must the wire be before the stress at its upper end reaches the proportionality limit, which is 8.0107N/m2 ?
Alarge uniform cylindrical steel rod of density =7.8g/cm3 is 2.0 m long and has a diameter of 5.0 cm. the rod is fastened to a concrete floor with its long axis vertical.what is the normal stress in the rod at the cross-section located at (a)1.0 mfrom its lower end?(b)1.5 m from the lower end?
A brass wire and a steel wire, both of the same length, are extended by 1.0 mm under the same force. Is the cross-sectional radius of the brass wire more, less, or equal to the cross-sectional radius of the steel wire? Explain. Youngs moduli for brass and steel are 1.0 1010 N/m2 and 2.0 1011 N/m2, respectively.
A uniform wire (Y = 2.0 1011 N/m2) is subjected to a longitudinal tensile stress of 4.0 107 N/m2. What is the fractional change in the length of the wire?
In Example 14.3, we found that one of the steel cables supporting an airplane at the Udvar-Hazy Center was under a tension of 9.30 103 N. Assume the cable has a diameter of 2.30 era and an initial length of 8.00 m before the plane is suspended on the cable. How much longer is the cable when the plane is suspended on it?
A steel cable 2.00 m in length and with cross-sectional radius 0.350 mm is used to suspend from the ceiling a 10.0-kg model aircraft that is flying in a horizontal circle with an angular speed of 6.00 rad/s. What is the strain produced in the cable?
Two rods, one made of copper and the other of steel, have the same dimensions. If the copper rod stretches by 0.15mm under some stress, how much does the steel rod stretch under the same stress?
Problems 33 and 34 are paired. One end of a uniform beam that weighs 2.80 102 N is attached to a wall with a hinge pin. The other end is supported by a cable making the angles shown in Figure P14.33. Find the tension in the cable. FIGURE P14.33 Problems 33 and 34.
Consider two steel rods, A and B. B has three times the area and twice the length of A, so Young's modulus for B will be what factor times Young's modulus for A?
The pole in the figure is a a 90° bend in a power line and is therefore subjected to more shear force than poles in straight parts of the line. The tension in the two wires at the top of the pole is 3.5 × 104 N, and both wires are at an angle of 80° with respect to the pole. The pole is 15 m tall, has an 16 cm diameter and can be considered to have half the strength of hardwood (hardwood has a Young's modulus of 1.5×1010 N/m2 and a shear modulus of 1×010 N/m2). a) First ignore the guy wire (Tgw). Calculate the compression of the pole, in millimeters. b) Still ignoring the guy wire, Find how much it bends in mm to the right. c) Now find the tension in the guy wire used to keep the pole straight if it is attached to the top of the pole at an angle of 30° with the vertical in Newtons. (The guy wire must be in the opposite direction of the bend.)
A shaft having length equal to 10 m and diameter equal to (50 + 21) mm is simply supported at both ends. The shaft carries four masses (150 + 21) kg, (200 + 22) kg, (250 + 21) kg and (300 + 21) kg. These masses are located at a distance of 1.5 m, 2.5 m, 5.5 m and 7.5 m from the left hand side support, respectively. The modulus of elasticity, E, for the material of the shaft is 200 GN/m2 and mass density for the shaft material is 7500 kg/m3. Determine critical speed of the shaft in revolutions per minute for the following two cases: i. Effect of the mass of the shaft is neglected. ii. Effect of the mass of the shaft is considered. What is the usefulness of the answers determined in this problem?