A 35-mm diameter rivet joins the plates that are each 150 mm wide. The allowable stresses are 200 MPa for bearing in the plate material and 80 MPa for shearing of the rivet. Determine the minimum thickness of each plate. Answer: t =

Q: Problem 4. EOM Derivation Derive the equation of motion for the following system: We want to measure…

A: The frictional torque is bω-dθdt.

Q: A projectile (mp = 59 g) traveling at v= 525 m/s strikes and becomes embedded in the block (m, = 39…

A: The given information in the problem is shown in the following attached image:

Q: True or false: The changes in the attributes of both systems may reach a particular state if there…

A: The statement appears to be describing the concept of thermal equilibrium. When two closed systems…

Q: Assume you are driving at the speed limit v0. As you approach an intersection 21.5 m wide, you see…

A: (a) Write the given data. Distance, S=21.5 mReaction time, treaction=0.690 sAcceleration, a=-2.7…

Q: A 60 B 4m 4m 4m 60 D P

A:

Q: If the resultant force of the two tugboats is required to be directed towards the positive x axis,…

A: According to the given data FA=2kN We need to find  Resultant Force  Force FB with angle

Q: Vibration is ubiquitous. It is seen in everyday life applications.  Discuss the typical applications…

A: Vibration is a mechanical phenomenon in which oscillations of particles occur about an equilibrium…

Q: Determine the tension developed in wire CA required for the equilibrium of the 11 kg cylinder. Take…

A: Equilibrium: In mechanics, equilibrium refers to a state of balance where the net force and moment…

Q: Air flows through a cylindrical combustion chamber of diameter 0.3 m and length 3 m as shown in the…

A: Given the inlet conditions of case-a as: Inlet stagnation temperature: T0 = 1,000 KInlet stagnation…

Q: A DVST, or Direct View Storage Tube, is a kind of optical storage medium.

A: Introduction A direct-view storage tube is similar to a cathode ray tube in that it employs an…

Q: 30° A 60

A: According to the given data  A load 340 N is carried by the rope A and B  We need to find Tension in…

Q: lem: Use a unit length for the gate, determine the height h (m) in fluid 2 in gure below if the…

A: Given: The distance from liquid surface to centroid of plane for fluid 1, h¯=12=0.5 m The area of…

Q: 12-6. Determine the equations of the elastic curve for th beam using the x₁ and x3 coordinates.…

A: The support reactions are : ΣFy=0Ay+RB=PΣMA=0P×3L2-RB×L=0RB=3P2Ay=P-32P=-P2

Q: In the paper mill, what six instructions lead to the manufacture of the design?

A: The specific six instructions that lead to the manufacture of a design in a paper mill can vary…

Q: You install a pumping well to recover the toluene. The pumping well is 6 inch diameter and the well…

A: Given: Pumping well diameter (D) = 6 inches = 0.5 feet Pumping well efficiency = 50% Assumed…

Q: If the magnitude of the resultant force acting on the eyebolt is 620 N and its direction measured…

A:

Q: Determine the relationship between the pressure difference and the relative density for it - For…

A: Draw the given diagram of the system.

Q: 1. If link AB rotates 360°, what is the maximum stroke (ARmax)? 2. As a rule of thumb, the…

A: It is required to determine the maximum stroke of the mechanism and it is also required to determine…

Q: In a skating jump, a skater rotates around their vertical central axis. During the jump, the…

A: Since you have posted a question with multiple sub parts, we will provide the solution only to the…

Q: 12.14 Blocks A and B weight 120 N and 200 N, respectively. Force P acts parallel to the plane, which…

A: The weight of block A is Wa=120 N The weight of block B is Wb=200 N The coefficient of friction…

Q: The Fourier heat conduction equation has been used to obtain the temperature-time response during…

A:

Q: The 2-lb collar is released from rest at A and slides down along the smooth rod as shown in (Eigure…

A: Given that: Stiffness = 4 lb/ft

Q: The A-36 steel plate has a thickness of 12 mm. If there are shoulder fillets at B and C, and allow =…

A: Given A36 steelt=12mmσallow=150MPa

Q: 4. For the structure below, draw the axial, shear and bending moment diagrams. Include the value of…

A: “Since you have posted a question with multiple sub-parts, we will provide the solution only to the…

Q: 2.) Water, with density at 1.94 slugs/ft3 and kinematic viscosity (v) at 0.000011 ft2/s, is pumped…

A:

Q: A double collar C is pin connected together such that one collar slides over a fixed rod and the…

A: At θ = 0°, the position of collar C on the rotating rod is at its highest point. Using the given…

Q: The pipe assembly is subjected to the 80-N force. Determine the moment of this force about point B,…

A: To find: The moment about the point B. Given: The force is F=80 N.

Q: For a steel alloy it has been determined that a carburizing heat treatment of 16 h duration at 731°C…

A: Given-Information:- Carbon concentration at 16hr and 731C = 0.40wt % at 3.9mm Carburizing…

Q: EXERCISE 2.53 Collar C is pushed along the guide bar defined by y= 2(1-0.25x²), where x and y have…

A: Given the angular velocity and mass of collar.  Required: Forces exerted on the collar by arm AB and…

Q: lamp=81kg, AB=5mm, BC=8mm

A:

Q: When an inductor and a resistor are connected in parallel, how many degrees out of phase are the…

A: According to Bartleby guidelines, we can solve only three sub part of a question at a time. you are…

Q: Determine the internal normal force, shear force and the moment at points C and D. 2 m 6 m C 45% 3 m…

A:

Q: Problem 4 Given: Cantilever beam with distributed loads as shown. Neglect beam self-weight. Find:…

A: According  to the given data A loading cantilever Beam We need to find Reaction at point A.

Q: has a stiff us damping A precision grinding achine is supported on constant of 4 kN-s/m. The floor…

A: The stiffness is k=2 MN/m=2*106 N/m. The viscous damping constant is c=4 kN-s/m=4*103 Ns/m. The…

Q: An ideal Otto engine, operating on the hot-air standard with k = 1.34, has a compression ratio of 5.…

A:

Q: If the fly walks away from the origin in the direction of u = i − 7j, the temperature it measures…

A:

Q: Determine the displacements at all nodes for the plane truss shown (Hint: you do not need to develop…

A: Since you have asked multiple questions, we will solve the first question for you. If you want any…

Q: The uniform pole has a weight W and is lowered slowly from a vertical position = 90° toward the…

A:

Q: The analyst in the Dorben Company wishes to assign a number of like facilities to an operator based…

A: Given-Information:- Loading machine standard time = 0.34 minutesUnloading machine standant time =…

Q: The frame ACD is hinged at A and D and is supported by a cable that passes through a ring at B and…

A: To find: The moment about the diagonal. Given: The tension in the cable is T=550 N. The frame is…

Q: For the motion given by the equations = X₁ cos wt + X₂ sin wt, x₂ = -X₁ sin wt + X₂ cos wt, x3 = (1…

A: Given That: The motion of a particle is described by the following equations: x1 = X1cos(ωt) + X2…

Q: an ericson cycle operates on 0.75 lbm ocygen from 60 psia and 1200degree F at the beginning of the…

A: To Find : The value of QA,QR,Wnet,η,Pm Given : The pressure is, P3=60Psia6.894kPa1Psia=413.64kPa The…

Q: L1=3.9m, L2=9.7m, L3=6.3m F1=8.8N, F2=5.8N, F3=7.4N calculate the sum of moments the weight of the…

A: Given

Q: 12-6. Determine the equations of the elastic curve for the beam using the x₁ and x3 coordinates.…

A: Given the loading conditions. Required: Equations of elastic curve and maximum deflection.

Q: The steel framework is used to support the reinforced stone concrete slab that is used for an…

A: To Find : The load that act along members BE and FED. Given : The thickness of slab is t=200mm. The…

Q: 200 mm 60 N D 60° -200 mm- с 60° B PROBLEM 3.71 60 Two parallel 60-N forces are applied as shown to…

A: Given data:- Parallel forces=60N Size of the square=200 mm To find:-the moment of the couple formed…

Q: The members of a truss are pin connected at joint O. Determine the magnitude of F₁ (in KN) for…

A: According to the given data F3=5kN at 30deg clockwise from -x-axis F4=7kN at third quadrant  we need…

Q: A lift cage in a mining operation has a mass of 1000kg when empty. When a fully laden with a mass of…

A: Given the mass of lift and load and speed and displacement of lift.  Required: Tension in the cable…

Q: 6. Translational Mechanical System: Find the transfer function G(s) = X₂(s)/ F(s) for each…

A: Write the given data. m=8 kgk=2 N/mc1=4 Ns/mc2=2 Ns/m Let x1(t) be the forward motion of 8 kg mass.…

Q: (a) A spherical shell is immersed in water. The density of the spherical shell is 1650 kg/m'. If the…

A: Note: As per policy, we can solve the first question from different multiple questions. Please…

Stress transformation

The term stress indicates the measure of internal forces that develop due to an external force's application on an object. When a specific external force is applied to an object, internal stress generates in the material. The value of stress can obtain by taking the ratio of the externally applied force and cross-sectional area of the object. There are different types of stress depending on the type of external force.